* [Hardware] LSISAS1064E
@ 2007-05-13 10:52 Anton Gorlov
2007-05-13 11:55 ` Sergey Vlasov
0 siblings, 1 reply; 20+ messages in thread
From: Anton Gorlov @ 2007-05-13 10:52 UTC (permalink / raw)
To: hardware
Приехал тут 1 сервант.. на котором стоит
LSISAS1064E (AHCI 0001.0100 32 slots 6 ports 3gbps 0x3a impl raid mode)
Я так понимаю - это ведь ниразу не аппратный рейд?
или ошибаюсь?
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 10:52 [Hardware] LSISAS1064E Anton Gorlov
@ 2007-05-13 11:55 ` Sergey Vlasov
2007-05-13 12:26 ` Anton Gorlov
` (2 more replies)
0 siblings, 3 replies; 20+ messages in thread
From: Sergey Vlasov @ 2007-05-13 11:55 UTC (permalink / raw)
To: hardware
[-- Attachment #1: Type: text/plain, Size: 931 bytes --]
On Sun, May 13, 2007 at 02:52:34PM +0400, Anton Gorlov wrote:
> Приехал тут 1 сервант.. на котором стоит
> LSISAS1064E (AHCI 0001.0100 32 slots 6 ports 3gbps 0x3a impl raid mode)
LSISAS1064E - это контроллер SAS, а то, что в скобках - это SATA
(вероятно, встроенное в чипсет). Покажите lspci -vvnn полностью.
> Я так понимаю - это ведь ниразу не аппратный рейд?
Да, именно так (и драйверы, где есть какая-то поддержка этого RAID,
как обычно, бинарные).
Посмотрите в BIOS, есть ли возможность переключить этот контроллер в
режим без поддержки RAID - в этом случае LSISAS1064E должен
поддерживаться модулем mptsas (в режиме RAID у этого устройства
меняется как минимум PCI ID). В случае SATA RAID на похожих платах
модуль ahci должен подхватывать устройство и в режиме RAID, но могут
быть проблемы с загрузкой (например, BIOS может потребовать, чтобы
создали хоть какой-то массив - хотя бы из одного диска).
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 11:55 ` Sergey Vlasov
@ 2007-05-13 12:26 ` Anton Gorlov
2007-05-13 12:39 ` Anton Gorlov
2007-05-15 10:38 ` Anton Gorlov
2 siblings, 0 replies; 20+ messages in thread
From: Anton Gorlov @ 2007-05-13 12:26 UTC (permalink / raw)
To: hardware
Sergey Vlasov пишет:
>> Приехал тут 1 сервант.. на котором стоит
>> LSISAS1064E (AHCI 0001.0100 32 slots 6 ports 3gbps 0x3a impl raid mode)
> LSISAS1064E - это контроллер SAS, а то, что в скобках - это SATA
> (вероятно, встроенное в чипсет). Покажите lspci -vvnn полностью.
щас подумаю как закопипейстиь с этого сервера данные.. на нём пока нет
ничего..
>> Я так понимаю - это ведь ниразу не аппратный рейд?
> Да, именно так (и драйверы, где есть какая-то поддержка этого RAID,
> как обычно, бинарные).
:-(
> Посмотрите в BIOS, есть ли возможность переключить этот контроллер в
> режим без поддержки RAID - в этом случае LSISAS1064E должен
> поддерживаться модулем mptsas (в режиме RAID у этого устройства
> меняется как минимум PCI ID). В случае SATA RAID на похожих платах
> модуль ahci должен подхватывать устройство и в режиме RAID, но могут
> быть проблемы с загрузкой (например, BIOS может потребовать, чтобы
> создали хоть какой-то массив - хотя бы из одного диска).
Угу выбор режимов есть - рейд,сата ahci.. В редиме рпейда не видны
диски.. пробовал убунту, дебиан етч с ядром 2.6.18-4
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 11:55 ` Sergey Vlasov
2007-05-13 12:26 ` Anton Gorlov
@ 2007-05-13 12:39 ` Anton Gorlov
2007-05-13 13:12 ` Sergey Vlasov
2007-05-13 13:35 ` Konstantin A. Lepikhov
2007-05-15 10:38 ` Anton Gorlov
2 siblings, 2 replies; 20+ messages in thread
From: Anton Gorlov @ 2007-05-13 12:39 UTC (permalink / raw)
To: hardware
[-- Attachment #1: Type: text/plain, Size: 342 bytes --]
Sergey Vlasov пишет:
> On Sun, May 13, 2007 at 02:52:34PM +0400, Anton Gorlov wrote:
>> Приехал тут 1 сервант.. на котором стоит
>> LSISAS1064E (AHCI 0001.0100 32 slots 6 ports 3gbps 0x3a impl raid mode)
>
> LSISAS1064E - это контроллер SAS, а то, что в скобках - это SATA
> (вероятно, встроенное в чипсет). Покажите lspci -vvnn полностью.
[-- Attachment #2: lspci-r --]
[-- Type: text/plain, Size: 32750 bytes --]
00:00.0 Host bridge [0600]: Intel Corporation 5000P Chipset Memory Controller Hub [8086:25d8] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 0
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable-
Address: fee00000 Data: 0000
Capabilities: [6c] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Root: Correctable+ Non-Fatal+ Fatal+ PME+
00:02.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 [8086:25f7] (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=06, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: b8000000-b8afffff
Prefetchable memory behind bridge: 00000000a0000000-00000000a01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 40b9
Capabilities: [6c] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 2
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Root: Correctable+ Non-Fatal+ Fatal+ PME+
00:03.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 [8086:25e3] (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 40c1
Capabilities: [6c] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 3
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Root: Correctable- Non-Fatal- Fatal- PME-
00:04.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 [8086:25f8] (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 40c9
Capabilities: [6c] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 4
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 6, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:05.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 5 [8086:25e5] (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 40d1
Capabilities: [6c] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 5
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Root: Correctable- Non-Fatal- Fatal- PME-
00:06.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x8 Port 6-7 [8086:25f9] (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 40d9
Capabilities: [6c] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 6
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 6, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:07.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 7 [8086:25e7] (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 40e1
Capabilities: [6c] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 7
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Root: Correctable- Non-Fatal- Fatal- PME-
00:08.0 System peripheral [0880]: Intel Corporation 5000 Series Chipset DMA Engine [8086:1a38] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 1
Region 0: Memory at fe700000 (64-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: fee00000 Data: 0000
Capabilities: [6c] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM L1 Enabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
00:10.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Error Reporting Registers [8086:25f0] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:10.1 Host bridge [0600]: Intel Corporation 5000 Series Chipset Error Reporting Registers [8086:25f0] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:10.2 Host bridge [0600]: Intel Corporation 5000 Series Chipset Error Reporting Registers [8086:25f0] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:11.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved Registers [8086:25f1] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:13.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved Registers [8086:25f3] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:15.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers [8086:25f5] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:16.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers [8086:25f6] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:1d.0 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 [8086:2688] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 66
Region 4: I/O ports at 40a0 [size=32]
00:1d.1 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 [8086:2689] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 74
Region 4: I/O ports at 4080 [size=32]
00:1d.2 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #3 [8086:268a] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 66
Region 4: I/O ports at 4060 [size=32]
00:1d.3 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #4 [8086:268b] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 74
Region 4: I/O ports at 4040 [size=32]
00:1d.7 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller [8086:268c] (rev 09) (prog-if 20)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 66
Region 0: Memory at b8c00400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev d9) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: b8b00000-b8bfffff
Prefetchable memory behind bridge: 00000000b0000000-00000000b7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Intel Corporation Unknown device [8086:346d]
00:1f.0 ISA bridge [0601]: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller [8086:2670] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 631xESB/632xESB IDE Controller [8086:269e] (rev 09) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 82
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 40c0 [size=16]
00:1f.2 RAID bus controller [0104]: Intel Corporation 631xESB/632xESB SATA Storage Controller RAID [8086:2682] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 82
Region 0: I/O ports at 40d8 [size=8]
Region 1: I/O ports at 40f4 [size=4]
Region 2: I/O ports at 40d0 [size=8]
Region 3: I/O ports at 40f0 [size=4]
Region 4: I/O ports at 4020 [size=32]
Region 5: Memory at b8c00000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] #12 [0010]
00:1f.3 SMBus [0c05]: Intel Corporation 631xESB/632xESB/3100 Chipset SMBus Controller [8086:269b] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 4000 [size=32]
01:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Upstream Port [8086:3500] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=01, secondary=02, subordinate=05, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: b8000000-b89fffff
Prefetchable memory behind bridge: 00000000a0000000-00000000a01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express Upstream Port IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: SlotPowerLimit 0.000000
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Intel Corporation Unknown device [8086:346d]
01:00.3 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X Bridge [8086:350c] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=01, secondary=06, subordinate=06, sec-latency=48
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Intel Corporation Unknown device [8086:346d]
Capabilities: [d8] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
Status: Dev=00:00.3 64bit- 133MHz- SCD- USC- SCO- SRD-
Upstream: Capacity=65535 CommitmentLimit=65535
Downstream: Capacity=65535 CommitmentLimit=65535
02:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E1 [8086:3510] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: b8900000-b89fffff
Prefetchable memory behind bridge: 00000000a0000000-00000000a01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express Downstream Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn+ PwrCtrl+ MRL+ AtnInd+ PwrInd+ HotPlug+ Surpise-
Slot: Number 2, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee00000 Data: 40e9
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Intel Corporation Unknown device [8086:346d]
02:01.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E2 [8086:3514] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=02, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express Downstream Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee00000 Data: 4032
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Intel Corporation Unknown device [8086:346d]
02:02.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E3 [8086:3518] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=02, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: b8000000-b88fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express Downstream Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee00000 Data: 403a
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Intel Corporation Unknown device [8086:346d]
03:00.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic Unknown device [1000:0057] (rev 02)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at b8910000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at b8900000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at a0000000 [disabled] [size=2M]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Express Endpoint IRQ 0
Device: Supported: MaxPayload 4096 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Capabilities: [98] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [b0] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003000
05:00.0 Ethernet controller [0200]: Intel Corporation 631xESB/632xESB DPT LAN Controller Copper [8086:1096] (rev 01)
Subsystem: Intel Corporation Unknown device [8086:346c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 106
Region 0: Memory at b8820000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at b8400000 (32-bit, non-prefetchable) [size=4M]
Region 2: I/O ports at 2020 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee00000 Data: 406a
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM unknown, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
05:00.1 Ethernet controller [0200]: Intel Corporation 631xESB/632xESB DPT LAN Controller Copper [8086:1096] (rev 01)
Subsystem: Intel Corporation Unknown device [8086:346c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 98
Region 0: Memory at b8800000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at b8000000 (32-bit, non-prefetchable) [size=4M]
Region 2: I/O ports at 2000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM unknown, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
0c:0c.0 VGA compatible controller [0300]: ATI Technologies Inc ES1000 [1002:515e] (rev 02)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 1000 [size=256]
Region 2: Memory at b8b00000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fffe0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 12:39 ` Anton Gorlov
@ 2007-05-13 13:12 ` Sergey Vlasov
2007-05-13 13:23 ` Anton Gorlov
2007-05-13 13:37 ` Anton Gorlov
2007-05-13 13:35 ` Konstantin A. Lepikhov
1 sibling, 2 replies; 20+ messages in thread
From: Sergey Vlasov @ 2007-05-13 13:12 UTC (permalink / raw)
To: hardware
[-- Attachment #1: Type: text/plain, Size: 1216 bytes --]
On Sun, May 13, 2007 at 04:39:40PM +0400, Anton Gorlov wrote:
> Sergey Vlasov пишет:
> >On Sun, May 13, 2007 at 02:52:34PM +0400, Anton Gorlov wrote:
> >>Приехал тут 1 сервант.. на котором стоит
> >>LSISAS1064E (AHCI 0001.0100 32 slots 6 ports 3gbps 0x3a impl raid mode)
> 00:1f.2 RAID bus controller [0104]: Intel Corporation 631xESB/632xESB SATA Storage Controller RAID [8086:2682] (rev 09)
> Subsystem: Intel Corporation Unknown device [8086:346d]
Это SATA-"RAID", который сейчас поддерживается модулем ahci как
обычный контроллер SATA.
> 03:00.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic Unknown device [1000:0057] (rev 02)
> Subsystem: Intel Corporation Unknown device [8086:346d]
А вот это как раз и есть LSISAS1064E в режиме "RAID", для которого
драйвер отсутствует (за исключением упомянутой бинарщины). Есть ли
для него какой-то переключатель режима в настройках BIOS (или,
возможно, перемычка на плате)? В нормальном режиме этот контроллер
должен иметь PCI ID 1000:0056.
Ещё можно попробовать загрузить модуль mptsas и выполнить
echo '1000 0057' >/sys/bus/pci/drivers/mptsas/new_id
Или диски там подключены к SATA, а SAS на самом деле не используется?
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 13:12 ` Sergey Vlasov
@ 2007-05-13 13:23 ` Anton Gorlov
2007-05-13 15:20 ` Sergey Vlasov
2007-05-13 13:37 ` Anton Gorlov
1 sibling, 1 reply; 20+ messages in thread
From: Anton Gorlov @ 2007-05-13 13:23 UTC (permalink / raw)
To: hardware
Sergey Vlasov пишет:
> Это SATA-"RAID", который сейчас поддерживается модулем ahci как
> обычный контроллер SATA.
То есть как нормальный рейд он не увидится..можно забыть про эту мечту?
>> 03:00.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic Unknown device [1000:0057] (rev 02)
>> Subsystem: Intel Corporation Unknown device [8086:346d]
> А вот это как раз и есть LSISAS1064E в режиме "RAID", для которого
> драйвер отсутствует (за исключением упомянутой бинарщины). Есть ли
> для него какой-то переключатель режима в настройках BIOS (или,
> возможно, перемычка на плате)? В нормальном режиме этот контроллер
> должен иметь PCI ID 1000:0056.
Да..в биосе ест ьвыбор реима - sata,ahci,raid.
> Ещё можно попробовать загрузить модуль mptsas и выполнить
> echo '1000 0057' >/sys/bus/pci/drivers/mptsas/new_id
> Или диски там подключены к SATA, а SAS на самом деле не используется?
Да не -в рейде они в менюшке видны... и само оно гвоорит тчо из 2
дисков хандлед 1 логикал драйв.
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 12:39 ` Anton Gorlov
2007-05-13 13:12 ` Sergey Vlasov
@ 2007-05-13 13:35 ` Konstantin A. Lepikhov
2007-05-13 13:39 ` Anton Gorlov
1 sibling, 1 reply; 20+ messages in thread
From: Konstantin A. Lepikhov @ 2007-05-13 13:35 UTC (permalink / raw)
To: hardware
Hi Anton!
Sunday 13, at 04:39:40 PM you wrote:
...
> 05:00.0 Ethernet controller [0200]: Intel Corporation 631xESB/632xESB
> DPT LAN Controller Copper [8086:1096] (rev 01)
это случайно не от supermicro железка? e1000 на ней нормально 2 порта
видят?
--
WBR et al.
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 13:12 ` Sergey Vlasov
2007-05-13 13:23 ` Anton Gorlov
@ 2007-05-13 13:37 ` Anton Gorlov
1 sibling, 0 replies; 20+ messages in thread
From: Anton Gorlov @ 2007-05-13 13:37 UTC (permalink / raw)
To: hardware
Sergey Vlasov пишет:
> Ещё можно попробовать загрузить модуль mptsas и выполнить
> echo '1000 0057' >/sys/bus/pci/drivers/mptsas/new_id
В таком виде при включенном недорейде в биосе увидилсоь 2 отдельных винта.
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 13:35 ` Konstantin A. Lepikhov
@ 2007-05-13 13:39 ` Anton Gorlov
0 siblings, 0 replies; 20+ messages in thread
From: Anton Gorlov @ 2007-05-13 13:39 UTC (permalink / raw)
To: hardware
Konstantin A. Lepikhov пишет:
>> 05:00.0 Ethernet controller [0200]: Intel Corporation 631xESB/632xESB
>> DPT LAN Controller Copper [8086:1096] (rev 01)
> это случайно не от supermicro железка? e1000 на ней нормально 2 порта
> видят?
Наврядли..это чисто интеловсая железка..
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 13:23 ` Anton Gorlov
@ 2007-05-13 15:20 ` Sergey Vlasov
2007-05-13 17:50 ` Anton Gorlov
0 siblings, 1 reply; 20+ messages in thread
From: Sergey Vlasov @ 2007-05-13 15:20 UTC (permalink / raw)
To: hardware
[-- Attachment #1: Type: text/plain, Size: 2338 bytes --]
On Sun, May 13, 2007 at 05:23:06PM +0400, Anton Gorlov wrote:
> >> 00:1f.2 RAID bus controller [0104]: Intel Corporation 631xESB/632xESB SATA Storage Controller RAID [8086:2682] (rev 09)
> > Это SATA-"RAID", который сейчас поддерживается модулем ahci как
> > обычный контроллер SATA.
> То есть как нормальный рейд он не увидится..можно забыть про эту мечту?
Обычный SoftRAID, аппаратно там ничего не реализовано.
На самом деле для похожих SATA существует как минимум 3 разных
реализации SoftRAID - "родная" от Intel, от Adaptec (на некоторых
платах от Supermicro в BIOS предусмотрены оба варианта), и вот эта от
LSI. В Linux ни один из этих вариантов нормально не поддерживается
(вроде бы для старых Intel была какая-то поддержка в dmraid, но пишут,
что с новыми версиями чипсетов и BIOS эта поддержка уже не работает).
> >> 03:00.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic Unknown device [1000:0057] (rev 02)
> >> Subsystem: Intel Corporation Unknown device [8086:346d]
> > А вот это как раз и есть LSISAS1064E в режиме "RAID", для которого
> > драйвер отсутствует (за исключением упомянутой бинарщины). Есть ли
> > для него какой-то переключатель режима в настройках BIOS (или,
> > возможно, перемычка на плате)? В нормальном режиме этот контроллер
> > должен иметь PCI ID 1000:0056.
> Да..в биосе ест ьвыбор реима - sata,ahci,raid.
Если это одна опция с тремя возможными значениями, она явно относится
не к этому контроллеру, а к встроенному в чипсет AHCI. Хотя в
принципе там могли и как-то скомбинировать это переключение режимов -
закрытый драйвер для поддержки этого SoftRAID общий для SATA и SAS
(несмотря на то, что аппаратно это совершенно различные устройства).
> > Ещё можно попробовать загрузить модуль mptsas и выполнить
> > echo '1000 0057' >/sys/bus/pci/drivers/mptsas/new_id
> > Или диски там подключены к SATA, а SAS на самом деле не используется?
> В таком виде при включенном недорейде в биосе увидилсоь 2 отдельных винта.
Значит, диски всё-таки подключены к SAS - тогда ahci можно просто
игнорировать.
А что происходит при выключенном RAID в BIOS - диски в Linux видны
сразу (или хотя бы после загрузки mptsas, если по каким-то причинам он
не загружается автоматически)? Что при этом в lspci - по-прежнему
1000:0057, или всё-таки 1000:0056?
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 15:20 ` Sergey Vlasov
@ 2007-05-13 17:50 ` Anton Gorlov
2007-05-13 19:11 ` Sergey Vlasov
2007-05-15 21:21 ` Michael Shigorin
0 siblings, 2 replies; 20+ messages in thread
From: Anton Gorlov @ 2007-05-13 17:50 UTC (permalink / raw)
To: hardware
Sergey Vlasov пишет:
> Обычный SoftRAID, аппаратно там ничего не реализовано.
Угу..так ид умал. Тепеь осталось найти оффициальную какую-нибудь инфу
чтоб успокоить начальство..
> Если это одна опция с тремя возможными значениями, она явно относится
> не к этому контроллеру, а к встроенному в чипсет AHCI. Хотя в
> принципе там могли и как-то скомбинировать это переключение режимов -
> закрытый драйвер для поддержки этого SoftRAID общий для SATA и SAS
> (несмотря на то, что аппаратно это совершенно различные устройства).
ЯА больше никаких опций там и нет..и меню рейда появилсоь толькопосле
того как в биосе включил.
> А что происходит при выключенном RAID в BIOS - диски в Linux видны
> сразу (или хотя бы после загрузки mptsas, если по каким-то причинам он
> не загружается автоматически)?
Сразу.. вывод lspci смогу только завтра закинуть.
--
np: silence
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 17:50 ` Anton Gorlov
@ 2007-05-13 19:11 ` Sergey Vlasov
2007-05-14 6:06 ` Anton Gorlov
2007-05-15 21:21 ` Michael Shigorin
1 sibling, 1 reply; 20+ messages in thread
From: Sergey Vlasov @ 2007-05-13 19:11 UTC (permalink / raw)
To: hardware
[-- Attachment #1: Type: text/plain, Size: 2078 bytes --]
On Sun, May 13, 2007 at 09:50:19PM +0400, Anton Gorlov wrote:
> Sergey Vlasov пишет:
>
> > Обычный SoftRAID, аппаратно там ничего не реализовано.
> Угу..так ид умал. Тепеь осталось найти оффициальную какую-нибудь инфу
> чтоб успокоить начальство..
http://www.intel.com/support/ru/motherboards/server/sb/CS-023481.htm
(если я правильно угадал, что это какая-то из вариаций на тему S5000*)
SW RAID = Intel Embedded Server RAID Technology II, utilizing system
processor(s) and memory.
HW RAID = Intel Integrated RAID, utilizing dedicated Intel IO Processor 333
and dedicated memory for outstanding performance and reliability.
И HW RAID там имеется только в модели S5000PSLROMB, причём требует
дополнительной покупки ключа активации и модуля памяти.
Особенно "радует" новый способ отъёма денег у покупателя - этот их
SW RAID, помимо обычно встречающихся в подобных случаях RAID 0/1/10,
поддерживает ещё и RAID 5, но для этого требуется докупить "ключ
активации" за $100.
> > Если это одна опция с тремя возможными значениями, она явно относится
> > не к этому контроллеру, а к встроенному в чипсет AHCI. Хотя в
> > принципе там могли и как-то скомбинировать это переключение режимов -
> > закрытый драйвер для поддержки этого SoftRAID общий для SATA и SAS
> > (несмотря на то, что аппаратно это совершенно различные устройства).
> А больше никаких опций там и нет..и меню рейда появилсоь толькопосле
> того как в биосе включил.
Вроде бы пишут, что опции для SATA и SAS отдельные:
http://www.intel.com/support/ru/motherboards/server/sb/CS-025445.htm
> > А что происходит при выключенном RAID в BIOS - диски в Linux видны
> > сразу (или хотя бы после загрузки mptsas, если по каким-то причинам он
> > не загружается автоматически)?
>
> Сразу.. вывод lspci смогу только завтра закинуть.
Тогда, видимо, такой вариант и стоит использовать, если нет желания
возиться с бинарным драйвером (который, как обычно, имеет невнятную
лицензию - непонятно, можно ли его вообще выкладывать в собранном для
нашего ядра виде).
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 19:11 ` Sergey Vlasov
@ 2007-05-14 6:06 ` Anton Gorlov
0 siblings, 0 replies; 20+ messages in thread
From: Anton Gorlov @ 2007-05-14 6:06 UTC (permalink / raw)
To: hardware
Sergey Vlasov пишет:
>>> А что происходит при выключенном RAID в BIOS - диски в Linux видны
>>> сразу (или хотя бы после загрузки mptsas, если по каким-то причинам он
>>> не загружается автоматически)?
>> Сразу.. вывод lspci смогу только завтра закинуть.
> Тогда, видимо, такой вариант и стоит использовать, если нет желания
> возиться с бинарным драйвером (который, как обычно, имеет невнятную
> лицензию - непонятно, можно ли его вообще выкладывать в собранном для
> нашего ядра виде).
Вот тут вроде чтто в исходных кодак есть.. бинарей в архиве невидно
http://www.lsi.com/storage_home/products_home/standard_product_ics/sas_ics/lsisas1064e/index.html
А если бинарный откуда можно стянуть,если что?
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 11:55 ` Sergey Vlasov
2007-05-13 12:26 ` Anton Gorlov
2007-05-13 12:39 ` Anton Gorlov
@ 2007-05-15 10:38 ` Anton Gorlov
2 siblings, 0 replies; 20+ messages in thread
From: Anton Gorlov @ 2007-05-15 10:38 UTC (permalink / raw)
To: hardware
[-- Attachment #1: Type: text/plain, Size: 315 bytes --]
В чём может быть проблема -при загрузке доходит до сообщений:
snpchp: standart hot plug pci controller driver version 0.1
real time clock driver v1.12ac
input: PC Speaker as /class/input/input1
после чего на сервере рсабатывает алярма..и он умирает..перестаёт
реагировать на клаву и загрузка тоже останавливается.
[-- Attachment #2: lspci-r --]
[-- Type: text/plain, Size: 32751 bytes --]
00:00.0 Host bridge [0600]: Intel Corporation 5000P Chipset Memory Controller Hub [8086:25d8] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 0
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable-
Address: fee00000 Data: 0000
Capabilities: [6c] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Root: Correctable+ Non-Fatal+ Fatal+ PME+
00:02.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 [8086:25f7] (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=06, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: b8000000-b8afffff
Prefetchable memory behind bridge: 00000000a0000000-00000000a01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 40b9
Capabilities: [6c] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 2
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Root: Correctable+ Non-Fatal+ Fatal+ PME+
00:03.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 [8086:25e3] (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 40c1
Capabilities: [6c] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 3
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Root: Correctable- Non-Fatal- Fatal- PME-
00:04.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 [8086:25f8] (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 40c9
Capabilities: [6c] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 4
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 6, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:05.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 5 [8086:25e5] (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 40d1
Capabilities: [6c] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 5
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Root: Correctable- Non-Fatal- Fatal- PME-
00:06.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x8 Port 6-7 [8086:25f9] (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 40d9
Capabilities: [6c] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 6
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 6, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:07.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 7 [8086:25e7] (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable+
Address: fee00000 Data: 40e1
Capabilities: [6c] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 7
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Root: Correctable- Non-Fatal- Fatal- PME-
00:08.0 System peripheral [0880]: Intel Corporation 5000 Series Chipset DMA Engine [8086:1a38] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 1
Region 0: Memory at fe700000 (64-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: fee00000 Data: 0000
Capabilities: [6c] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM L1 Enabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
00:10.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Error Reporting Registers [8086:25f0] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:10.1 Host bridge [0600]: Intel Corporation 5000 Series Chipset Error Reporting Registers [8086:25f0] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:10.2 Host bridge [0600]: Intel Corporation 5000 Series Chipset Error Reporting Registers [8086:25f0] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:11.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved Registers [8086:25f1] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:13.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved Registers [8086:25f3] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:15.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers [8086:25f5] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:16.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers [8086:25f6] (rev b1)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:1d.0 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 [8086:2688] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 66
Region 4: I/O ports at 40a0 [size=32]
00:1d.1 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 [8086:2689] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 74
Region 4: I/O ports at 4080 [size=32]
00:1d.2 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #3 [8086:268a] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 66
Region 4: I/O ports at 4060 [size=32]
00:1d.3 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #4 [8086:268b] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 74
Region 4: I/O ports at 4040 [size=32]
00:1d.7 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller [8086:268c] (rev 09) (prog-if 20)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 66
Region 0: Memory at b8c00400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev d9) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: b8b00000-b8bfffff
Prefetchable memory behind bridge: 00000000b0000000-00000000b7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Intel Corporation Unknown device [8086:346d]
00:1f.0 ISA bridge [0601]: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller [8086:2670] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 631xESB/632xESB IDE Controller [8086:269e] (rev 09) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 82
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 40c0 [size=16]
00:1f.2 RAID bus controller [0104]: Intel Corporation 631xESB/632xESB SATA Storage Controller RAID [8086:2682] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 82
Region 0: I/O ports at 40d8 [size=8]
Region 1: I/O ports at 40f4 [size=4]
Region 2: I/O ports at 40d0 [size=8]
Region 3: I/O ports at 40f0 [size=4]
Region 4: I/O ports at 4020 [size=32]
Region 5: Memory at b8c00000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] #12 [0010]
00:1f.3 SMBus [0c05]: Intel Corporation 631xESB/632xESB/3100 Chipset SMBus Controller [8086:269b] (rev 09)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 4000 [size=32]
01:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Upstream Port [8086:3500] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=01, secondary=02, subordinate=05, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: b8000000-b89fffff
Prefetchable memory behind bridge: 00000000a0000000-00000000a01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express Upstream Port IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: SlotPowerLimit 0.000000
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Intel Corporation Unknown device [8086:346d]
01:00.3 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X Bridge [8086:350c] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=01, secondary=06, subordinate=06, sec-latency=48
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Intel Corporation Unknown device [8086:346d]
Capabilities: [d8] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
Status: Dev=00:00.3 64bit- 133MHz- SCD- USC- SCO- SRD-
Upstream: Capacity=65535 CommitmentLimit=65535
Downstream: Capacity=65535 CommitmentLimit=65535
02:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E1 [8086:3510] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: b8900000-b89fffff
Prefetchable memory behind bridge: 00000000a0000000-00000000a01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express Downstream Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn+ PwrCtrl+ MRL+ AtnInd+ PwrInd+ HotPlug+ Surpise-
Slot: Number 2, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee00000 Data: 40e9
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Intel Corporation Unknown device [8086:346d]
02:01.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E2 [8086:3514] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=02, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express Downstream Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee00000 Data: 4032
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Intel Corporation Unknown device [8086:346d]
02:02.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E3 [8086:3518] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=02, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: b8000000-b88fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express Downstream Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee00000 Data: 403a
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Subsystem: Intel Corporation Unknown device [8086:346d]
03:00.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic Unknown device [1000:0057] (rev 02)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at b8910000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at b8900000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at a0000000 [disabled] [size=2M]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Express Endpoint IRQ 0
Device: Supported: MaxPayload 4096 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Capabilities: [98] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [b0] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003000
05:00.0 Ethernet controller [0200]: Intel Corporation 631xESB/632xESB DPT LAN Controller Copper [8086:1096] (rev 01)
Subsystem: Intel Corporation Unknown device [8086:346c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 106
Region 0: Memory at b8820000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at b8400000 (32-bit, non-prefetchable) [size=4M]
Region 2: I/O ports at 2020 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee00000 Data: 406a
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM unknown, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
05:00.1 Ethernet controller [0200]: Intel Corporation 631xESB/632xESB DPT LAN Controller Copper [8086:1096] (rev 01)
Subsystem: Intel Corporation Unknown device [8086:346c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 98
Region 0: Memory at b8800000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at b8000000 (32-bit, non-prefetchable) [size=4M]
Region 2: I/O ports at 2000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM unknown, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
0c:0c.0 VGA compatible controller [0300]: ATI Technologies Inc ES1000 [1002:515e] (rev 02)
Subsystem: Intel Corporation Unknown device [8086:346d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 1000 [size=256]
Region 2: Memory at b8b00000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fffe0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-13 17:50 ` Anton Gorlov
2007-05-13 19:11 ` Sergey Vlasov
@ 2007-05-15 21:21 ` Michael Shigorin
2007-05-16 8:32 ` Anton Gorlov
1 sibling, 1 reply; 20+ messages in thread
From: Michael Shigorin @ 2007-05-15 21:21 UTC (permalink / raw)
To: hardware
On Sun, May 13, 2007 at 09:50:19PM +0400, Anton Gorlov wrote:
> > Обычный SoftRAID, аппаратно там ничего не реализовано.
> Угу..так ид умал. Тепеь осталось найти оффициальную
> какую-нибудь инфу чтоб успокоить начальство..
Здрасьте, "вот сгорит этот хрентроллер и куда мы будем
подвешивать диски, чтобы информацию выцарапать?".
Линуксовый md хоть от этого страхует.
--
---- WBR, Michael Shigorin <mike@altlinux.ru>
------ Linux.Kiev http://www.linux.kiev.ua/
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-15 21:21 ` Michael Shigorin
@ 2007-05-16 8:32 ` Anton Gorlov
2007-05-22 12:54 ` Alex
0 siblings, 1 reply; 20+ messages in thread
From: Anton Gorlov @ 2007-05-16 8:32 UTC (permalink / raw)
To: hardware
Michael Shigorin пишет:
>> Угу..так ид умал. Тепеь осталось найти оффициальную
>> какую-нибудь инфу чтоб успокоить начальство..
> Здрасьте, "вот сгорит этот хрентроллер и куда мы будем
> подвешивать диски, чтобы информацию выцарапать?".
> Линуксовый md хоть от этого страхует.
Там оказалось всё ещё хуже.. линукс вообще на этой плате не заводится :-(
S5000PAL
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-16 8:32 ` Anton Gorlov
@ 2007-05-22 12:54 ` Alex
2007-05-22 19:30 ` Michael Shigorin
0 siblings, 1 reply; 20+ messages in thread
From: Alex @ 2007-05-22 12:54 UTC (permalink / raw)
To: hardware, Anton Gorlov
Антон, вы не поделитесь, чем все завершилось у вас с этим железом.
А то тут имеются вот 2 брата близнеца...."спецы" по RHEL пятерку свою не смогли
нормально туда взгромоздить....причем я не понял почему.
Браться мне пробовать ставить туда server 4.0?
On Wed, 16 May 2007 12:32:14 +0400
Anton Gorlov wrote:
>
> Там оказалось всё ещё хуже.. линукс вообще на этой плате не заводится :-(
> S5000PAL
Алекс.
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-22 12:54 ` Alex
@ 2007-05-22 19:30 ` Michael Shigorin
2007-05-23 11:32 ` Alex
0 siblings, 1 reply; 20+ messages in thread
From: Michael Shigorin @ 2007-05-22 19:30 UTC (permalink / raw)
To: hardware
On Tue, May 22, 2007 at 04:54:24PM +0400, Alex wrote:
> Браться мне пробовать ставить туда server 4.0?
Пробуйте, я про какую-то 5000 ещё осенью отчёт слал
(работало, разве что на 2.6.16 пришлось сбэкпортить
e1000 из 2.6.17 -- было внесено в пакет, а с тех пор
уже и неактуально).
--
---- WBR, Michael Shigorin <mike@altlinux.ru>
------ Linux.Kiev http://www.linux.kiev.ua/
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-22 19:30 ` Michael Shigorin
@ 2007-05-23 11:32 ` Alex
2007-05-23 11:39 ` Konstantin A. Lepikhov
0 siblings, 1 reply; 20+ messages in thread
From: Alex @ 2007-05-23 11:32 UTC (permalink / raw)
To: hardware; +Cc: shigorin
Не, не получилось ничего. Софтрайд пишет что время синка 10Г раздела - 1000минут :)
Перепробовал все комбинации опций в биосе.
S5000PAL.
On Tue, 22 May 2007 22:30:19 +0300
Michael Shigorin wrote:
> On Tue, May 22, 2007 at 04:54:24PM +0400, Alex wrote:
> > Браться мне пробовать ставить туда server 4.0?
>
> Пробуйте, я про какую-то 5000 ещё осенью отчёт слал
> (работало, разве что на 2.6.16 пришлось сбэкпортить
> e1000 из 2.6.17 -- было внесено в пакет, а с тех пор
> уже и неактуально).
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [Hardware] LSISAS1064E
2007-05-23 11:32 ` Alex
@ 2007-05-23 11:39 ` Konstantin A. Lepikhov
0 siblings, 0 replies; 20+ messages in thread
From: Konstantin A. Lepikhov @ 2007-05-23 11:39 UTC (permalink / raw)
To: hardware
<цитата от="Alex">
> Не, не получилось ничего. Софтрайд пишет что время синка 10Г раздела -
> 1000минут :)
> Перепробовал все комбинации опций в биосе.
> S5000PAL.
а hdparm -tT что по этим дискам показывает? Может, просто скорость
синхронизации понижена.
--
WBR et al.
^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2007-05-23 11:39 UTC | newest]
Thread overview: 20+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2007-05-13 10:52 [Hardware] LSISAS1064E Anton Gorlov
2007-05-13 11:55 ` Sergey Vlasov
2007-05-13 12:26 ` Anton Gorlov
2007-05-13 12:39 ` Anton Gorlov
2007-05-13 13:12 ` Sergey Vlasov
2007-05-13 13:23 ` Anton Gorlov
2007-05-13 15:20 ` Sergey Vlasov
2007-05-13 17:50 ` Anton Gorlov
2007-05-13 19:11 ` Sergey Vlasov
2007-05-14 6:06 ` Anton Gorlov
2007-05-15 21:21 ` Michael Shigorin
2007-05-16 8:32 ` Anton Gorlov
2007-05-22 12:54 ` Alex
2007-05-22 19:30 ` Michael Shigorin
2007-05-23 11:32 ` Alex
2007-05-23 11:39 ` Konstantin A. Lepikhov
2007-05-13 13:37 ` Anton Gorlov
2007-05-13 13:35 ` Konstantin A. Lepikhov
2007-05-13 13:39 ` Anton Gorlov
2007-05-15 10:38 ` Anton Gorlov
ALT Linux hardware support
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/hardware/0 hardware/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 hardware hardware/ http://lore.altlinux.org/hardware \
hardware@altlinux.ru hardware@lists.altlinux.org hardware@lists.altlinux.ru hardware@lists.altlinux.com hardware@altlinux.org
public-inbox-index hardware
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.hardware
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git