[Comm] nut (UPS фирмы POWERCOM)

[Comm] nut (UPS фирмы POWERCOM)

[Дворников Михаил]

Установлены nut(1.4.0),nut-server,knutclient
UPS фирмы "POWERCOM" KING-625AP.
com-порт на компьютере только один.
Как я понял upsd не запустился.

/etc/nut/ups.conf
[Powercom]
         driver = powercom
         port = /dev/ttyS0
         desc = "KING-625AP"

/var/log/messages
  upsdrvctl: Serial port read timed out
  upsdrvctl: Network UPS Tools - UPS driver controller 1.4.0
  upsdrvctl: Startup timer elapsed, continuing...
  upsd: Starting UPS drivers:  succeeded
  upsd[1212]: Can't connect to UPS [Powercom] (powercom-ttyS0): 
Connection refused
  upsd: Can't connect to UPS [Powercom] (powercom-ttyS0): Connection refused
  upsd[1212]: /usr/share/cmdvartab not found - disabling descriptions
  upsd: /usr/share/cmdvartab not found - disabling descriptions
  upsd: Network UPS Tools upsd 1.4.0
  upsd: Synchronizing...
  upsd: .
  last message repeated 3 times
  upsd: . giving up
  upsd: upsd startup succeeded
  upsd[1213]: Startup successful
-- 
С уважением, Дворников Михаил.

Re: [Comm] nut (UPS фирмы POWERCOM)

[Alexey Morsov]

Дворников Михаил wrote:
> Установлены nut(1.4.0),nut-server,knutclient
> UPS фирмы "POWERCOM" KING-625AP.
> com-порт на компьютере только один.
> Как я понял upsd не запустился.
Ну вот у меня Powercom kingpro-625 - с apcupsd прекрасно работает

-- 
Всего наилучшего,
Системный Администратор ЗАО "ИК "РИКОМ-ТРАСТ"
Алексей Морсов
ICQ: 196766290
Jabber: Samurai@jabber.ru
http://www.ricom.ru
http://www.fondmarket.ru

Re: [Comm] nut (UPS фирмы POWERCOM)

[Mike Lykov]

В сообщении от Четверг 30 Сентябрь 2004 11:56 Дворников Михаил написал:

> [Powercom]
>          driver = powercom
>          port = /dev/ttyS0
>   upsd[1212]: Can't connect to UPS [Powercom] (powercom-ttyS0):
> Connection refused

а в чем вопрос-то? разберитесь, почему это connection -то refused

-- 
Mike Lykov
Samara, "Vesna" parfum company, System administrator 

Re: [Comm] nut (UPS фирмы POWERCOM)

[Дворников Михаил]

Mike Lykov пишет:
> а в чем вопрос-то? разберитесь, почему это connection -то refused
А это и есть главный вопрос :)
Кабель подключен, настройки сделаны, а он refused...
Может KING-625AP не дружит с nut?
-- 
С уважением, Дворников Михаил.

Re: [Comm] nut (UPS фирмы POWERCOM)

[Antonio]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

On Thu, 30 Sep 2004, Дворников Михаил wrote:

> UPS фирмы "POWERCOM" KING-625AP.
>
> /etc/nut/ups.conf
> [Powercom]
>          driver = powercom
>          port = /dev/ttyS0
>          desc = "KING-625AP"

desc -- нафиг, играйте с параметром type. К примеру, для
KIN-525AP это будет KIN525AP. Для вашего, возможно, подойдут
KP625AP или какой-то другой.

Когда будете пробовать различные варианты, надо вручную убивать
всё, относящееся к предыдущему запуску (оно запускается, но
ничего не делает).

Возможно, что где-то напутано с правами.

- -- 
Best regards,
	Tony.			mailto:obidos@mail.ru
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.0 (GNU/Linux)

iD8DBQFBW7bx2gaLrWRbr5URAtuyAJ90d9SdAVWuvLbWdE6cMykjiY0YzwCeJzI+
kouv0fyz/pK7e5qILN74b1E=
=61yf
-----END PGP SIGNATURE-----

Re: [Comm] nut (UPS фирмы POWERCOM)

[Дворников Михаил]

Alexey Morsov пишет:
> 
> Дворников Михаил wrote:
> 
>> Установлены nut(1.4.0),nut-server,knutclient
>> UPS фирмы "POWERCOM" KING-625AP.
>> com-порт на компьютере только один.
>> Как я понял upsd не запустился.
> 
> Ну вот у меня Powercom kingpro-625 - с apcupsd прекрасно работает
> 
Внимательнее посмотрел оказывается тоже KING PRO (KIN-625AP).
У Вас наверно тоже KIN-625AP. KIN-625 без порта RS-232.
Покажите, plz, конфиги apcupsd.

На ночь выключают электричество. Как можно сделать, чтобы компьютер
включался при появлении питания. На старых компах с механической
кнопкой включения такое проходило.
В KIN-625AP - есть только таймер отключения :(

С UPS идет программа upsmon для Linux, проверил нормально работает.
Но она не rpm ;)
-- 
С уважением, Дворников Михаил.

Re: [Comm] nut (UPS фирмы POWERCOM)

[Alexey Morsov]

[-- Attachment #1: Type: text/plain, Size: 470 bytes --]


Дворников Михаил wrote:

> С UPS идет программа upsmon для Linux, проверил нормально работает.
> Но она не rpm ;)
То что там идет я даже не смотрел - у нас разные упс и на всех 
стоит apcupsd

Конфиг прилагаю.

Оно кстаит и выключает комп при отсутствии электричества в 
течении указанного времени.

-- 
Всего наилучшего,
Системный Администратор ЗАО "ИК "РИКОМ-ТРАСТ"
Алексей Морсов
ICQ: 196766290
Jabber: Samurai@jabber.ru
http://www.ricom.ru
http://www.fondmarket.ru

[-- Attachment #2: apcupsd.conf --]
[-- Type: text/plain, Size: 10690 bytes --]

## apcupsd.conf v1.1 ##
# 
#  for apcupsd release 3.10.13 (16 April 2004) - redhat
#
# "apcupsd" POSIX config file
#
# ========= General configuration parameters ============
#
# UPSNAME xxx
#   Use this to give your UPS a name in log files and such. This
#   is particulary useful if you have multiple UPSes.  This does not
#   set the EEPROM.
#UPSNAME
#
# UPSCABLE [ simple    | smart     | ether     | usb |
#            940-0119A | 940-0127A | 940-0128A | 940-0020B |
#            940-0020C | 940-0023A | 940-0024B | 940-0024C |
#            940-1524C | 940-0024G | 940-0095A | 940-0095B |
#            940-0095C | M-04-02-2000 ]
#
# defines the type of cable that you have.
UPSCABLE smart
#
# Old types, still valid, are mapped to the new drivers
# 
#           keyword       driver used     
# UPSTYPE [ backups        dumb
#         | sharebasic     dumb
#         | netups         dumb
#         | backupspro     apcsmart
#         | smartvsups     apcsmart
#         | newbackupspro  apcsmart
#         | backupspropnp  apcsmart
#         | smartups       apcsmart
#         | matrixups      apcsmart
#         | sharesmart     apcsmart
#
# *** New driver names. They can be used directly 
#       rather than using one of the above aliases.
#
# UPSTYPE [ dumb | apcsmart | net | usb | snmp | test]
#
# defines the type of UPS you have.
UPSTYPE smartups
#
#
#DEVICE <string> /dev/<serial port>
# name of your UPS device
#
# Here a table of the possible devices related with the UPS drivers.
#
#   NOTE!!! for USB devices, please use a form indicated below 
#      including the [0-15] as written!
#
# Driver   Device                    Description
# dumb     /dev/tty**                Serial character device
# apcsmart /dev/tty**                Serial character device
# usb      /dev/usb/hiddev[0-15]     On most systems
# net      hostname:port             Network link to a master apcupsd
#                                    through NIS
# snmp     hostname:port:vendor:community
#                                    SNMP Network link to an SNMP-enabled
#                                    UPS device. Vendor is the MIB used by
#                                    the UPS device: can be "APC" or "RFC"
#                                    where APC is the powernet MIB and RFC
#                                    is the IETF's rfc1628 UPS-MIB.
#                                    Port is usually 161.
DEVICE /dev/ttyS0
#
#LOCKFILE <path to lockfile>
# path for serial port lock file
LOCKFILE /var/lock
#
#
#
# ======== configuration parameters used during power failures ==========
#
# The ONBATTERYDELAY is the time in seconds from when a power failure
#   is detected until we react to it with an onbattery event.
#
#   This means that, apccontrol will be called with the powerout argument
#   immediately when a power failure is detected.  However, the
#   onbattery argument is passed to apccontrol only after the 
#   ONBATTERYDELAY time.  If you don't want to be annoyed by short
#   powerfailures, make sure that apccontrol powerout does nothing
#   i.e. comment out the wall.
ONBATTERYDELAY 6
# 
# Note: BATTERYLEVEL, MINUTES, and TIMEOUT work in conjunction, so
# the first that occurs will cause the initation of a shutdown.
#
# If during a power failure, the remaining battery percentage
# (as reported by the UPS) is below or equal to BATTERYLEVEL, 
# apcupsd will initiate a system shutdown.
BATTERYLEVEL 10
#
#
# If during a power failure, the remaining runtime in minutes 
# (as calculated internally by the UPS) is below or equal to MINUTES,
# apcupsd, will initiate a system shutdown.
MINUTES 3
#
#
# If during a power failure, the UPS has run on batteries for TIMEOUT
# many seconds or longer, apcupsd will initiate a system shutdown.
# A value of 0 disables this timer.
#
#  Note, if you have a Smart UPS, you will most likely want to disable
#    this timer by setting it to zero. That way, you UPS will continue
#    on batteries until either the % charge remaing drops to or below BATTERYLEVEL,
#    or the remaining battery runtime drops to or below MINUTES.  Of course,
#    if you are testing, setting this to 60 causes a quick system shutdown
#    if you pull the power plug.   
#  If you have an older dumb UPS, you will want to set this to less than
#    the time you know you can run on batteries.
TIMEOUT 0
#
#
#  Time in seconds between annoying users to signoff prior to
#  system shutdown. 0 disables.
ANNOY 300
#
# Initial delay after power failure before warning users to get
# off the system.
ANNOYDELAY 60
#
# The condition which determines when users are prevented from
# logging in during a power failure.
# NOLOGON <string> [ disable | timeout | percent | minutes | always ]
NOLOGON disable
#
#
# If killdelay is set, apcupsd will continue running after a
# shutdown has been requested, and after the specified time in
# seconds attempt to kill the power.  This is for use on systems
# where apcupsd cannot regain control after a shutdown.
# KILLDELAY <seconds>  0 disables
KILLDELAY 0
#
#
# ==== Configuration statements the network information server =========
#
# NETSERVER [ on | off ] on enables, off disables the network
#  information server. If netstatus is on, a network information
#  server process will be started for serving the STATUS and
#  EVENT data over the network (used by CGI programs).
NETSERVER on
#
# NISIP <dotted notation ip address>
#  IP address on which NIS server will listen for incoming connections.
#  Default value is 0.0.0.0 that means any incoming request will be
#  serviced but if you want it to listen to a single subnet you can
#  set it up to that subnet address, for example 192.168.10.0
#  Additionally you can listen for a single IP like 192.168.10.1
NISIP 0.0.0.0
#
# NISPORT <port> default is 3551 as registered with the IANA
#  port to use for sending STATUS and EVENTS data over the network.
#  It is not used unless NETSERVER is on. If you change this port,
#  you will need to change the corresponding value in the cgi directory
#  and rebuild the cgi programs.
NISPORT 3551
#
# If you want the last few EVENTS to be available over the network
# by the network information server, you must define an EVENTSFILE.
EVENTSFILE /var/log/apcupsd.events
#
# EVENTSFILEMAX <kilobytes>
#  By default, the size of the EVENTSFILE will be not be allowed to exceed
#  10 kilobytes.  When the file grows beyond this limit, older EVENTS will
#  be removed from the beginning of the file (first in first out).  The
#  parameter EVENTSFILEMAX can be set to a different kilobyte value, or set
#  to zero to allow the EVENTSFILE to grow without limit.
EVENTSFILEMAX 10
#
# ========== Configuration statements used if sharing =============
#            a UPS and controlling it via the network              
#
#      The configuration statements below are used if you
#      want to share one UPS to power multiple machines and have them
#      communicate by the network. Obviously, the master is connected
#      to the UPS via the serial cable, and it communicates to the
#      "slaves" via the network -- i.e. the slaves get their info
#      concerning the UPS via the ethernet.
#
# UPSCLASS [ standalone | shareslave | sharemaster | netslave | netmaster ]
# normally standalone unless you share a UPS with multiple machines.
UPSCLASS standalone
#
# Unless you want to share the UPS (power multiple machines).
#  this should be disable
# UPSMODE [ disable | share | net | sharenet ]
UPSMODE disable
#
# NETTIME <int>
#NETTIME 100
#
# NETPORT <int>
#NETPORT 6666
#
# MASTER <machine-name>
#MASTER
#
# SLAVE <machine-name>
#SLAVE slave1
#SLAVE slave2
#
# USERMAGIC <string>
#USERMAGIC
#
#
#
#
# ===== Configuration statements to control apcupsd system logging ========
#
# Time interval in seconds between writing the STATUS file; 0 disables
STATTIME 0
#
# Location of STATUS file (written to only if STATTIME is non-zero)
STATFILE /var/log/apcupsd.status
#
#
# LOGSTATS [ on | off ] on enables, off disables
# Note! This generates a lot of output, so if         
#       you turn this on, be sure that the
#       file defined in syslog.conf for LOG_NOTICE is a named pipe.
#  You probably do not want this on.
LOGSTATS off
#
#
# Time interval in seconds between writing the DATA records to
#   the log file. 0 disables.
DATATIME 0
#
# FACILITY defines the logging facility (class) for logging to syslog. 
#          If not specified, it defaults to "daemon". This is useful 
#          if you want to separate the data logged by apcupsd from other
#          programs.
#FACILITY DAEMON
#
#
#
#
# ========== Configuration statements used in updating the UPS EPROM =========
#
# UPS name, max 8 characters  -- used only during -n or --rename-ups
#UPSNAME UPS_IDEN
#
# Battery date - 8 characters -- used only during -u or --update-battery-date
#BATTDATE mm/dd/yy
#
#  The following items are set during -c or --configure
#                       
# Sensitivity to line voltage quality (H cause faster transfer to batteries)  
# SENSITIVITY H M L        (default = H)
#SENSITIVITY H
#
# UPS delay after power return (seconds)
# WAKEUP 000 060 180 300   (default = 0)
#WAKEUP 60
#
# UPS Grace period after request to power off (seconds)
# SLEEP 020 180 300 600    (default = 20)
#SLEEP 180
#
#
# Low line voltage causing transfer to batteries
# The permitted values depend on your model as defined by last letter 
#  of FIRMWARE or APCMODEL. Some representative values are:
#    D 106 103 100 097
#    M 177 172 168 182
#    A 092 090 088 086
#    I 208 204 200 196     (default = 0 => not valid)
LOTRANSFER 200
#
# High line voltage causing transfer to batteries
# The permitted values depend on your model as defined by last letter 
#  of FIRMWARE or APCMODEL. Some representative values are:
#    D 127 130 133 136
#    M 229 234 239 224
#    A 108 110 112 114
#    I 253 257 261 265     (default = 0 => not valid)
#HITRANSFER 253
#
# Battery change needed to restore power
# RETURNCHARGE 00 15 50 90 (default = 15)
#RETURNCHARGE 15
#
# Alarm delay 
# 0 = zero delay after pwr fail, T = power fail + 30 sec, L = low battery, N = never
# BEEPSTATE 0 T L N        (default = 0)
BEEPSTATE T
#
# Low battery warning delay in minutes
# LOWBATT 02 05 07 10      (default = 02)
#LOWBATT 2
#
# UPS Output voltage when running on batteries
# The permitted values depend on your model as defined by last letter 
#  of FIRMWARE or APCMODEL. Some representative values are:
#    D 115
#    M 208
#    A 100
#    I 230 240 220 225     (default = 0 => not valid)
#OUTPUTVOLTS 230
#
# Self test interval in hours 336=2 weeks, 168=1 week, ON=at power on
# SELFTEST 336 168 ON OFF  (default = 336)
#SELFTEST 336
#
#

[Comm] Re: nut (UPS фирмы POWERCOM)

[Konstantin A. Lepikhov]

Hi Дворников!

Thursday 30, at 05:25:32 PM you wrote:

> На ночь выключают электричество. Как можно сделать, чтобы компьютер
> включался при появлении питания. На старых компах с механической
> кнопкой включения такое проходило.
> В KIN-625AP - есть только таймер отключения :(
на новых с ATX тоже проходит - посмотрите на пункты power after fail в
BIOS, там можно поставить on - оно и будет включаться при подаче питания.

-- 
WBR, Konstantin	      chat with ==>ICQ: 109916175
     Lepikhov,	      speak  to ==>JID: lakostis@jabber.org
aka L.A. Kostis       write  to ==>mailto:lakostis@pisem.net.nospam

...The information is like the bank... 			  (c) EC8OR

Re: [Comm] nut (UPS фирмы POWERCOM)

[Дворников Михаил]

Alexey Morsov пишет:
> 
> Дворников Михаил wrote:
> 
>> С UPS идет программа upsmon для Linux, проверил нормально работает.
>> Но она не rpm ;)
> 
> То что там идет я даже не смотрел - у нас разные упс и на всех стоит 
> apcupsd
> 
> Конфиг прилагаю.
> 
> Оно кстаит и выключает комп при отсутствии электричества в течении 
> указанного времени.

Не судьба ...
На корпусе UPS написано KIN-625AP.
C типом кабеля "UPSCABLE smart" сразу не запускается.
С остальными вроде запускается, но работу от аккумуляторов не видит.
Попробовал nut. Запускается, но после полминуты работы в логах пишет 
проверьте драйвер.