* [Comm] bonding и обычный свитч
@ 2005-08-18 5:36 Pavel Stoliarov
2005-08-18 5:49 ` Pavel Stoliarov
0 siblings, 1 reply; 2+ messages in thread
From: Pavel Stoliarov @ 2005-08-18 5:36 UTC (permalink / raw)
To: community
Всем привет .
Появилась необходимость увеличить пропускную способность с сервера .
Попалась вот эта статья :
http://www.linuxhorizon.ro/bonding.html
Интересно, а с обычным свитчем , не поддерживающим port trunc'ng это будет
работать ?
Интересны такжы режимы ( mode )
Я так понял из документации , что для моего случая подойдет mode=2
( XOR policy: Transmit based on [(source MAC address XOR'd with destination
MAC address) modulo slave count]. This selects the same slave for each
destination MAC address. This mode provides load balancing and fault
tolerance. )
--
Best regards
Pavel Stoliarov
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [Comm] bonding и обычный свитч
2005-08-18 5:36 [Comm] bonding и обычный свитч Pavel Stoliarov
@ 2005-08-18 5:49 ` Pavel Stoliarov
0 siblings, 0 replies; 2+ messages in thread
From: Pavel Stoliarov @ 2005-08-18 5:49 UTC (permalink / raw)
To: ALT Linux Community
В сообщении от Четверг 18 Август 2005 10:36 Pavel Stoliarov написал(a):
> Всем привет .
>
> Появилась необходимость увеличить пропускную способность с сервера .
> Попалась вот эта статья :
> http://www.linuxhorizon.ro/bonding.html
>
> Интересно, а с обычным свитчем , не поддерживающим port trunc'ng это будет
> работать ?
>
> Интересны такжы режимы ( mode )
> Я так понял из документации , что для моего случая подойдет mode=2
> ( XOR policy: Transmit based on [(source MAC address XOR'd with destination
> MAC address) modulo slave count]. This selects the same slave for each
> destination MAC address. This mode provides load balancing and fault
> tolerance. )
Похоже что mode=6 больше походит.. Вроде как обычный свитчи подойдут...
mode=6 (balance-alb)
Adaptive load balancing: includes balance-tlb plus receive load balancing
(rlb) for IPV4 traffic, and does not require any special switch support. The
receive load balancing is achieved by ARP negotiation. The bonding driver
intercepts the ARP Replies sent by the local system on their way out and
overwrites the source hardware address with the unique hardware address of
one of the slaves in the bond such that different peers use different
hardware addresses for the server.
--
Best regards
Pavel Stoliarov
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2005-08-18 5:49 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2005-08-18 5:36 [Comm] bonding и обычный свитч Pavel Stoliarov
2005-08-18 5:49 ` Pavel Stoliarov
ALT Linux Community general discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
public-inbox-index community
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.community
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git