* [Sysadmins] pppoe проблема
@ 2007-08-01 6:17 Igo
2007-08-01 8:17 ` Igo
0 siblings, 1 reply; 4+ messages in thread
From: Igo @ 2007-08-01 6:17 UTC (permalink / raw)
To: ALT Linux sysadmin discuss
всем привет
alm4
поставил pppoe работает, но после разрыва получаю след.:
[root@localhost ~]# service pppoe start
Bringing up PPPoE link................TIMED OUT
[root@localhost ~]# service network restart
......
Starting group 1/realphys (3 interfaces)
Starting eth0: ......OK
Starting eth1: .......OK
Starting eth2: SIOCGIFFLAGS: No such device
!FAILED
[root@localhost ~]# ls -l /etc/net/ifaces/eth2
total 4
-rw-r--r-- 1 root root 0 Jul 31 16:31 ipv4address
-rw-r--r-- 1 root root 0 Jul 17 22:23 ipv4route
-rw------- 1 root root 27 Aug 1 14:15 options
вписываю USE_HOTPLUG=yes
[root@localhost eth2]# cat options
DISABLED=no
USE_HOTPLUG=yes
[root@localhost ~]# service network restart
........
Starting eth2: skipping hotplug iface 'eth2'
SKIPPED
[FAILED]
[root@localhost ~]# tail /var/log/messages
......
Aug 1 14:11:49 localhost kernel: e1000: eth0: e1000_watchdog: NIC Link
is Up 100 Mbps Full Duplex
Aug 1 14:11:49 localhost kernel: e1000: eth0: e1000_watchdog: 10/100
speed: disabling TSO
Aug 1 14:11:49 localhost kernel: e1000: eth1: e1000_watchdog: NIC Link
is Up 100 Mbps Full Duplex
даже невидит сетевую хотя
[root@localhost ~]# pciscan
Recommended driver Description
------------------ -----------
..........
e1000 Intel Corporation 82573E Gigabit Ethernet
Controller (Copper) [Ethernet controller]
skge D-Link System Inc Gigabit Ethernet Adapter
[Ethernet controller]
e1000 Intel Corporation 82541GI Gigabit Ethernet
Controller [Ethernet controller]
[root@localhost ~]# lsmod|grep skg
skge 43536 0
если перегрузить комп то всё работает нормально до первого разрыва с
провайдером
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [Sysadmins] pppoe проблема
2007-08-01 6:17 [Sysadmins] pppoe проблема Igo
@ 2007-08-01 8:17 ` Igo
2007-08-01 8:41 ` Anton Gorlov
0 siblings, 1 reply; 4+ messages in thread
From: Igo @ 2007-08-01 8:17 UTC (permalink / raw)
To: altlinux, ALT Linux sysadmin discuss
может подскажите как хотя бы реанимировать eth2 ? очень странная ситуация
> всем привет
> alm4
> поставил pppoe работает, но после разрыва получаю след.:
>
> [root@localhost ~]# service pppoe start
> Bringing up PPPoE link................TIMED OUT
>
> [root@localhost ~]# service network restart
> ......
> Starting group 1/realphys (3 interfaces)
> Starting eth0: ......OK
> Starting eth1: .......OK
> Starting eth2: SIOCGIFFLAGS: No such device
> !FAILED
> [root@localhost ~]# ls -l /etc/net/ifaces/eth2
> total 4
> -rw-r--r-- 1 root root 0 Jul 31 16:31 ipv4address
> -rw-r--r-- 1 root root 0 Jul 17 22:23 ipv4route
> -rw------- 1 root root 27 Aug 1 14:15 options
>
> вписываю USE_HOTPLUG=yes
> [root@localhost eth2]# cat options
> DISABLED=no
> USE_HOTPLUG=yes
>
> [root@localhost ~]# service network restart
> ........
> Starting eth2: skipping hotplug iface 'eth2'
> SKIPPED
> [FAILED]
>
> [root@localhost ~]# tail /var/log/messages
> ......
> Aug 1 14:11:49 localhost kernel: e1000: eth0: e1000_watchdog: NIC Link
> is Up 100 Mbps Full Duplex
> Aug 1 14:11:49 localhost kernel: e1000: eth0: e1000_watchdog: 10/100
> speed: disabling TSO
> Aug 1 14:11:49 localhost kernel: e1000: eth1: e1000_watchdog: NIC Link
> is Up 100 Mbps Full Duplex
>
> даже невидит сетевую хотя
>
> [root@localhost ~]# pciscan
> Recommended driver Description
> ------------------ -----------
> ..........
> e1000 Intel Corporation 82573E Gigabit Ethernet
> Controller (Copper) [Ethernet controller]
> skge D-Link System Inc Gigabit Ethernet Adapter
> [Ethernet controller]
> e1000 Intel Corporation 82541GI Gigabit Ethernet
> Controller [Ethernet controller]
>
> [root@localhost ~]# lsmod|grep skg
> skge 43536 0
>
> если перегрузить комп то всё работает нормально до первого разрыва с
> провайдером
>
>
> _______________________________________________
> Sysadmins mailing list
> Sysadmins@lists.altlinux.org
> https://lists.altlinux.org/mailman/listinfo/sysadmins
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [Sysadmins] pppoe проблема
2007-08-01 8:17 ` Igo
@ 2007-08-01 8:41 ` Anton Gorlov
2007-08-01 10:54 ` Igo
0 siblings, 1 reply; 4+ messages in thread
From: Anton Gorlov @ 2007-08-01 8:41 UTC (permalink / raw)
To: sysadmins
Igo пишет:
> может подскажите как хотя бы реанимировать eth2 ? очень странная ситуация
USE_HOTPLUG=no
[root@bulevar localnet]# cat options
TYPE=eth
USE_HOTPLUG=no
MODULE=sky2
ONBOOT=yes
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [Sysadmins] pppoe проблема
2007-08-01 8:41 ` Anton Gorlov
@ 2007-08-01 10:54 ` Igo
0 siblings, 0 replies; 4+ messages in thread
From: Igo @ 2007-08-01 10:54 UTC (permalink / raw)
To: ALT Linux sysadmin discuss
пробывал как вы советуете, тоже не помогло
вот что самое странное откуда взялся eth3 непонятно. сейчас сделал не
через службу pppoe а через etcnet
[root@localhost ~]# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:15:17:23:54:B3
inet addr:192.168.100.10 Bcast:192.168.100.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:188667 errors:0 dropped:0 overruns:0 frame:0
TX packets:199021 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:32481306 (30.9 MiB) TX bytes:113490638 (108.2 MiB)
Base address:0x2000 Memory:88180000-881a0000
eth1 Link encap:Ethernet HWaddr 00:15:17:23:54:B4
inet addr:192.168.23.2 Bcast:192.168.23.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:140461 errors:0 dropped:0 overruns:0 frame:0
TX packets:132183 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:82942967 (79.1 MiB) TX bytes:17374394 (16.5 MiB)
Base address:0x1200 Memory:88020000-88040000
eth3 Link encap:Ethernet HWaddr 00:11:95:ED:11:3F
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:233
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1550 errors:0 dropped:0 overruns:0 frame:0
TX packets:1550 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:177785 (173.6 KiB) TX bytes:177785 (173.6 KiB)
venet0 Link encap:UNSPEC HWaddr
00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:672 (672.0 b) TX bytes:280 (280.0 b)
> может подскажите как хотя бы реанимировать eth2 ? очень странная ситуация
>> всем привет
>> alm4
>> поставил pppoe работает, но после разрыва получаю след.:
>>
>> [root@localhost ~]# service pppoe start
>> Bringing up PPPoE link................TIMED OUT
>>
>> [root@localhost ~]# service network restart
>> ......
>> Starting group 1/realphys (3 interfaces)
>> Starting eth0: ......OK
>> Starting eth1: .......OK
>> Starting eth2: SIOCGIFFLAGS: No such device
>> !FAILED
>> [root@localhost ~]# ls -l /etc/net/ifaces/eth2
>> total 4
>> -rw-r--r-- 1 root root 0 Jul 31 16:31 ipv4address
>> -rw-r--r-- 1 root root 0 Jul 17 22:23 ipv4route
>> -rw------- 1 root root 27 Aug 1 14:15 options
>> вписываю USE_HOTPLUG=yes
>> [root@localhost eth2]# cat options
>> DISABLED=no
>> USE_HOTPLUG=yes
>>
>> [root@localhost ~]# service network restart
>> ........
>> Starting eth2: skipping hotplug iface 'eth2'
>> SKIPPED
>> [FAILED]
>>
>> [root@localhost ~]# tail /var/log/messages
>> ......
>> Aug 1 14:11:49 localhost kernel: e1000: eth0: e1000_watchdog: NIC
>> Link is Up 100 Mbps Full Duplex
>> Aug 1 14:11:49 localhost kernel: e1000: eth0: e1000_watchdog: 10/100
>> speed: disabling TSO
>> Aug 1 14:11:49 localhost kernel: e1000: eth1: e1000_watchdog: NIC
>> Link is Up 100 Mbps Full Duplex
>>
>> даже невидит сетевую хотя
>>
>> [root@localhost ~]# pciscan
>> Recommended driver Description
>> ------------------ -----------
>> ..........
>> e1000 Intel Corporation 82573E Gigabit Ethernet
>> Controller (Copper) [Ethernet controller]
>> skge D-Link System Inc Gigabit Ethernet Adapter
>> [Ethernet controller]
>> e1000 Intel Corporation 82541GI Gigabit Ethernet
>> Controller [Ethernet controller]
>>
>> [root@localhost ~]# lsmod|grep skg
>> skge 43536 0
>>
>> если перегрузить комп то всё работает нормально до первого разрыва с
>> провайдером
>>
>>
>> _______________________________________________
>> Sysadmins mailing list
>> Sysadmins@lists.altlinux.org
>> https://lists.altlinux.org/mailman/listinfo/sysadmins
>>
>
>
>
>
> Igo пишет:
>
>> может подскажите как хотя бы реанимировать eth2 ? очень странная ситуация
>>
> USE_HOTPLUG=no
>
>
> [root@bulevar localnet]# cat options
> TYPE=eth
> USE_HOTPLUG=no
> MODULE=sky2
> ONBOOT=yes
>
> _______________________________________________
> Sysadmins mailing list
> Sysadmins@lists.altlinux.org
> https://lists.altlinux.org/mailman/listinfo/sysadmins
>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2007-08-01 10:54 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2007-08-01 6:17 [Sysadmins] pppoe проблема Igo
2007-08-01 8:17 ` Igo
2007-08-01 8:41 ` Anton Gorlov
2007-08-01 10:54 ` Igo
ALT Linux sysadmins discussion
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/sysadmins/0 sysadmins/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 sysadmins sysadmins/ http://lore.altlinux.org/sysadmins \
sysadmins@lists.altlinux.org sysadmins@lists.altlinux.ru sysadmins@lists.altlinux.com
public-inbox-index sysadmins
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.sysadmins
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git