From: Nikolay <sn_kirovograd_sub@rambler.ru>
To: Sysadmins@lists.altlinux.org
Subject: [Sysadmins] QLogic Fibre Channel HBA
Date: Fri, 17 Aug 2007 10:11:16 +0300
Message-ID: <200708171011.16908.sn_kirovograd_sub@rambler.ru> (raw)
Доброго дня.
Возможно немного не по теме но всёже.
Решили мы познять сервер с REL 3.0 до REL 4.0 всё чудесно прошло - но теперь
система не видит LUN B адаптера - и соответственно небольшой кусочек БД на
нём. При борьбе с данной неприятностью был прочитан
http://download.qlogic.com/drivers/54333/README_qla2xxx2-6U3.htm
и /etc/modprobe.conf был приведён в следующий вид
options scsi_mod max_scsi_luns=255
alias eth0 e1000
alias eth1 e1000
alias eth2 e100
alias scsi_hostadapter aic79xx
alias scsi_hostadapter2 megaraid_mbox
alias usb-controller ohci-hcd
alias scsi_hostadapter1 qla2300 ql2xsuspendcount=12 displayConfig=1
alias scsi_hostadapter3 qla2300 ql2xsuspendcount=12 displayConfig=1
alias scsi_hostadapter4 qla2300_conf ql2xsuspendcount=12 displayConfig=1
options scsi_mod max_scsi_luns=255 scsi_allow_ghost_devices=1
последняя строка - так на всякий случай ..
но всё одно - при старте или
modprobe qla2300
мы видим следующее
Aug 17 10:02:07 app kernel: ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 23
(level, low) -> IRQ 201
Aug 17 10:02:07 app kernel: qla2300 0000:02:04.0: Found an ISP2312, irq 201,
iobase 0xf8844000
Aug 17 10:02:07 app kernel: qla2300 0000:02:04.0: Configuring PCI space...
Aug 17 10:02:07 app kernel: qla2300 0000:02:04.0: Configure NVRAM
parameters...
Aug 17 10:02:07 app kernel: qla2300 0000:02:04.0: Verifying loaded RISC
code...
Aug 17 10:02:07 app kernel: qla2300 0000:02:04.0: LIP reset occured (f8f7).
Aug 17 10:02:07 app kernel: qla2300 0000:02:04.0: Waiting for LIP to
complete...
Aug 17 10:02:07 app kernel: qla2300 0000:02:04.0: LIP occured (f8f7).
Aug 17 10:02:08 app kernel: qla2300 0000:02:04.0: LOOP UP detected (2 Gbps).
Aug 17 10:02:08 app kernel: qla2300 0000:02:04.0: Topology - (Loop), Host Loop
address 0x0
Aug 17 10:02:08 app kernel: scsi9 : qla2xxx
Aug 17 10:02:08 app kernel: qla2300 0000:02:04.0:
Aug 17 10:02:08 app kernel: QLogic Fibre Channel HBA Driver: 8.01.04-d7
Aug 17 10:02:08 app kernel: QLogic QLA2340 -
Aug 17 10:02:08 app kernel: ISP2312: PCI-X (100 MHz) @ 0000:02:04.0 hdma+,
host#=9, fw=3.03.20 IPX
Aug 17 10:02:08 app kernel: Vendor: EUROLOGC Model: FC2502 Rev:
7902
Aug 17 10:02:08 app kernel: Type: Direct-Access ANSI
SCSI revision: 02
Aug 17 10:02:08 app kernel: qla2300 0000:02:04.0: scsi(9:0:0:0): Enabled
tagged queuing, queue depth 32.
Aug 17 10:02:08 app kernel: SCSI device sdb: 824926208 512-byte hdwr sectors
(422362 MB)
Aug 17 10:02:08 app kernel: SCSI device sdb: drive cache: write back
Aug 17 10:02:08 app kernel: SCSI device sdb: 824926208 512-byte hdwr sectors
(422362 MB)
Aug 17 10:02:08 app kernel: SCSI device sdb: drive cache: write back
Aug 17 10:02:08 app kernel: sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 >
Aug 17 10:02:08 app kernel: Attached scsi disk sdb at scsi9, channel 0, id 0,
lun 0
Aug 17 10:02:08 app kernel: Attached scsi generic sg2 at scsi9, channel 0, id
0, lun 0, type 0
Aug 17 10:02:08 app scsi.agent[29125]: disk
at /devices/pci0000:02/0000:02:04.0/host9/target9:0:0/9:0:0:0
lsmod| grep qla
qla2300 129857 0
qla2xxx 164453 1 qla2300
scsi_transport_fc 12097 1 qla2xxx
scsi_mod 117709 6
qla2xxx,scsi_transport_fc,sg,megaraid_mbox,aic79xx,sd_mod
Если у кого нибуть есть опыт борьбы с данного вида криворукостью -
поделитесь .
При этом вывод REL 3.0
qla2x00_detect num_hosts=0
scsi1 : QLogic QLA2312 PCI to Fibre Channel Host Adapter: bus 2 device 4 irq
23
Firmware version: 3.03.01, Driver version 7.01.01
blk: queue f7319e18, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
Vendor: EUROLOGC Model: FC2502 Rev: 7902
Type: Direct-Access ANSI SCSI revision: 02
blk: queue f7319c18, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
Vendor: EUROLOGC Model: FC2502 Rev: 7902
Type: Direct-Access ANSI SCSI revision: 02
blk: queue f7319a18, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
scsi(1:0:0:0): Enabled tagged queuing, queue depth 32.
scsi(1:0:0:1): Enabled tagged queuing, queue depth 32.
Attached scsi disk sdc at scsi1, channel 0, id 0, lun 0
Attached scsi disk sdd at scsi1, channel 0, id 0, lun 1
Что и где я проморгал ?
--
С уважением, Николай
next reply other threads:[~2007-08-17 7:11 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-08-17 7:11 Nikolay [this message]
2007-08-17 12:39 ` Dmitry Lebkov
2007-08-17 15:40 ` Dmitry Lebkov
2007-08-20 10:05 ` Nikolay
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200708171011.16908.sn_kirovograd_sub@rambler.ru \
--to=sn_kirovograd_sub@rambler.ru \
--cc=Sysadmins@lists.altlinux.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
ALT Linux sysadmins discussion
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/sysadmins/0 sysadmins/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 sysadmins sysadmins/ http://lore.altlinux.org/sysadmins \
sysadmins@lists.altlinux.org sysadmins@lists.altlinux.ru sysadmins@lists.altlinux.com
public-inbox-index sysadmins
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.sysadmins
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git