* [sisyphus] hp sj2200c and sane @ 2006-04-25 9:05 Alexey Morsov 2006-04-25 19:11 ` Vitaly Lipatov 0 siblings, 1 reply; 11+ messages in thread From: Alexey Morsov @ 2006-04-25 9:05 UTC (permalink / raw) To: Sisyphus [-- Attachment #1: Type: text/plain, Size: 2097 bytes --] Привет, Еще одна поптыка заставить работать сканер работавший в сизифе какое-то время. Сканер HP ScanJet 2200c (USB). В мастере (и в сизифе одно время) работал. На сайте sane давно давно в списке полностью поддерживаемых. Ныне (уже несколько месяцев) он не работает. Посколько я не знаю как нынче все с usb сканерами устроено (а гугление выводит только на /dev/usbscanner или права на /proc/bus/usb/... И так имеем: morsov@alexey ~ $ sane-find-scanner # sane-find-scanner will now attempt to detect your scanner. If the # result is different from what you expected, first make sure your # scanner is powered up and properly connected to your computer. # No SCSI scanners found. If you expected something different, make sure that # you have loaded a kernel SCSI driver for your SCSI adapter. # Also you need support for SCSI Generic (sg) in your operating system. # If using Linux, try "modprobe sg". found USB scanner (vendor=0x03f0 [Hewlett-Packard], product=0x0605 [HP ScanJet 2200C], chip=LM9832/3) at libusb:001:014 morsov@alexey ~ $ ll -d /proc/bus/usb/001/014 -rw-rw---- 1 root scanner 57 Апр 25 12:51 /proc/bus/usb/001/014 Судя по информации с сайта sane для этого сканера используется plustek.conf В нем у меня device auto. Пробовал туда прописывать vendor/product id - не помогает. Пробовал закоментировать в dll.conf все кроме plustek. Тоже не помогает. Пользователь включен в группу scanner (да и из под рута тоже не видит). scanimage -L уверяет что устройства не найдено (и xsane), но оно есть, оно обнаруживается пересоздается в /proc/bus/usb и в логах тоже его при передергивании видно отчетливо. Вопрос что делать куда копать? Хочу сканер (задолбало уже ради сканирования странички грузить vmware с оффтопиком). -- С уважением, Алексей Морсов системный администратор ЗАО "ИК "Риком-Траст" ICQ: 196-766-290 Jabber: samurai@www.fondmarket.ru www.ricom.ru www.fondmarket.ru [playing] Yoko Kanno - ARJUNA into the another world - (2001) Я почти уверен, что проблема не в этом. -- ldv in devel@ [-- Attachment #2: Digital signature --] [-- Type: application/pgp-signature, Size: 481 bytes --] ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [sisyphus] hp sj2200c and sane 2006-04-25 9:05 [sisyphus] hp sj2200c and sane Alexey Morsov @ 2006-04-25 19:11 ` Vitaly Lipatov 2006-04-26 7:29 ` Alexey Morsov 0 siblings, 1 reply; 11+ messages in thread From: Vitaly Lipatov @ 2006-04-25 19:11 UTC (permalink / raw) To: ALT Linux Sisyphus discussion list On Tuesday 25 April 2006 13:05, Alexey Morsov wrote: > > scanimage -L уверяет что устройства не найдено (и xsane), но Покажите из-под root: # SANE_DEBUG_PLUSTEK=20 scanimage -L И grep -v "^#" /etc/sane.d/plustek.conf -- Lav Виталий Липатов Санкт-Петербург GNU! ALT Linux Team! WINE! LaTeX! LyX! http://freesource.info ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [sisyphus] hp sj2200c and sane 2006-04-25 19:11 ` Vitaly Lipatov @ 2006-04-26 7:29 ` Alexey Morsov 2006-04-26 20:40 ` Vitaly Lipatov 0 siblings, 1 reply; 11+ messages in thread From: Alexey Morsov @ 2006-04-26 7:29 UTC (permalink / raw) To: sisyphus [-- Attachment #1: Type: text/plain, Size: 12859 bytes --] On Tue, Apr 25, 2006 at 11:11:34PM +0400, Vitaly Lipatov wrote: > On Tuesday 25 April 2006 13:05, Alexey Morsov wrote: > > > > scanimage -L уверяет что устройства не найдено (и xsane), но > Покажите из-под root: > # SANE_DEBUG_PLUSTEK=20 scanimage -L > > И grep -v "^#" /etc/sane.d/plustek.conf root@alexey ~ # SANE_DEBUG_PLUSTEK=20 scanimage -L [sanei_debug] Setting debug level of plustek to 20. [plustek] Plustek backend V0.50-7, part of sane-backends 1.0.17 [plustek] Retrieving all supported and conntected devices [plustek] Checking for 0x07b3-0x0010 [plustek] Checking for 0x07b3-0x0011 [plustek] Checking for 0x07b3-0x0017 [plustek] Checking for 0x07b3-0x0015 [plustek] Checking for 0x07b3-0x0017 [plustek] Checking for 0x07b3-0x0013 [plustek] Checking for 0x07b3-0x0013 [plustek] Checking for 0x07b3-0x0011 [plustek] Checking for 0x07b3-0x0010 [plustek] Checking for 0x07b3-0x0014 [plustek] Checking for 0x07b3-0x0015 [plustek] Checking for 0x07b3-0x0014 [plustek] Checking for 0x07b3-0x0016 [plustek] Checking for 0x07b3-0x0017 [plustek] Checking for 0x07b3-0x0017 [plustek] Checking for 0x07b3-0x0007 [plustek] Checking for 0x07b3-0x000f [plustek] Checking for 0x07b3-0x000f [plustek] Checking for 0x07b3-0x0005 [plustek] Checking for 0x07b3-0x0014 [plustek] Checking for 0x07b3-0x0012 [plustek] Checking for 0x0400-0x1000 [plustek] Checking for 0x0400-0x1001 [plustek] Checking for 0x0400-0x1001 [plustek] Checking for 0x0458-0x2007 [plustek] Checking for 0x0458-0x2008 [plustek] Checking for 0x0458-0x2009 [plustek] Checking for 0x0458-0x2013 [plustek] Checking for 0x0458-0x2015 [plustek] Checking for 0x0458-0x2016 [plustek] Checking for 0x03f0-0x0505 [plustek] Checking for 0x03f0-0x0605 [plustek] Checking for 0x04b8-0x010f [plustek] Checking for 0x04b8-0x011d [plustek] Checking for 0x1606-0x0050 [plustek] Checking for 0x1606-0x0060 [plustek] Checking for 0x1606-0x0160 [plustek] Checking for 0x049f-0x001a [plustek] Checking for 0x04a9-0x2206 [plustek] Checking for 0x04a9-0x2207 [plustek] Checking for 0x04a9-0x2208 [plustek] Checking for 0x04a9-0x220d [plustek] Checking for 0x04a9-0x220e [plustek] Checking for 0x04a9-0x2220 [plustek] Available and supported devices: [plustek] Device: >libusb:001:003< - 0x03f0x0x0605 [plustek] ># Plustek-SANE Backend configuration file< [plustek] ># For use with LM9831/2/3 based USB scanners< [plustek] >#< [plustek] >< [plustek] ># each device needs at least two lines:< [plustek] ># - [usb] vendor-ID and product-ID< [plustek] ># - device devicename< [plustek] ># i.e. for Plustek (0x07B3) UT12/16/24 (0x0017)< [plustek] ># [usb] 0x07B3 0x0017< [plustek] ># device /dev/usbscanner< [plustek] ># or< [plustek] ># device libusb:bbb:ddd< [plustek] ># where bbb is the busnumber and ddd the device number< [plustek] ># make sure that your user has access to /proc/bus/usb/bbb/ddd< [plustek] >#< [plustek] ># additionally you can specify some options< [plustek] ># warmup, lOffOnEnd, lampOff< [plustek] >#< [plustek] ># For autodetection use< [plustek] ># [usb]< [plustek] ># device /dev/usbscanner< [plustek] >#< [plustek] ># or simply< [plustek] ># [usb]< [plustek] >#< [plustek] ># or if you want a specific device but you have no idea about the< [plustek] ># device node or you use libusb, simply set vendor- and product-ID< [plustek] ># [usb] 0x07B3 0x0017< [plustek] ># device auto< [plustek] >#< [plustek] ># NOTE: autodetection is safe, as it uses the info it got< [plustek] ># from the USB subsystem. If you're not using the< [plustek] ># autodetection, you MUST have attached that device< [plustek] ># at your USB-port, that you have specified...< [plustek] >#< [plustek] >< [plustek] >[usb] 0x03f0 0x0605< [plustek] next device is a USB device (0x03F0-0x0605) [plustek] ... next device [plustek] >< [plustek] >#< [plustek] ># options for the previous USB entry< [plustek] >#< [plustek] ># switch lamp off after xxx secs, 0 disables the feature< [plustek] ># (can also be set via frontend)< [plustek] >option lampOff 300< [plustek] Decoding option >lampOff< [plustek] >< [plustek] ># warmup period in seconds, 0 means no warmup, -1 means auto-warmup< [plustek] ># (can also be set via frontend)< [plustek] >option warmup -1< [plustek] Decoding option >warmup< [plustek] >< [plustek] ># 0 means leave lamp-status untouched, not 0 means switch off< [plustek] ># on sane_close< [plustek] ># (can also be set via frontend)< [plustek] >option lOffOnEnd 1< [plustek] Decoding option >lOffOnEnd< [plustek] >< [plustek] >#< [plustek] ># options to tweak the image start-position< [plustek] ># (WARNING: there's no internal range check!!!)< [plustek] >#< [plustek] ># for the normal scan area< [plustek] >#< [plustek] >option posOffX 0< [plustek] Decoding option >posOffX< [plustek] >option posOffY 0< [plustek] Decoding option >posOffY< [plustek] >< [plustek] ># for transparencies< [plustek] >option tpaOffX 0< [plustek] Decoding option >tpaOffX< [plustek] >option tpaOffY 0< [plustek] Decoding option >tpaOffY< [plustek] >< [plustek] ># for negatives< [plustek] >option negOffX 0< [plustek] Decoding option >negOffX< [plustek] >option negOffY 0< [plustek] Decoding option >negOffY< [plustek] >< [plustek] >#< [plustek] ># for setting the calibration strip position< [plustek] ># (WARNING: there's no internal range check!!!)< [plustek] ># -1 means use built in< [plustek] ># (can also be set via frontend)< [plustek] >option posShadingY -1< [plustek] Decoding option >posShadingY< [plustek] >option tpaShadingY -1< [plustek] Decoding option >tpaShadingY< [plustek] >option negShadingY -1< [plustek] Decoding option >negShadingY< [plustek] >< [plustek] >#< [plustek] ># to invert the negatives, 0 disables the feature< [plustek] >#< [plustek] >option invertNegatives 0< [plustek] Decoding option >invertNegatives< [plustek] >< [plustek] >#< [plustek] ># to disable the internal sensor speedup function,< [plustek] ># 1 disables the feature< [plustek] >#< [plustek] >option disableSpeedup 0< [plustek] Decoding option >disableSpeedup< [plustek] >< [plustek] >#< [plustek] ># to save/restore coarse calibration data< [plustek] ># (can also be set via frontend)< [plustek] >option cacheCalData 0< [plustek] Decoding option >cacheCalData< [plustek] >< [plustek] >#< [plustek] ># use alternate calibration routines< [plustek] >#< [plustek] >option altCalibration 0< [plustek] Decoding option >altCalibration< [plustek] >< [plustek] >#< [plustek] ># for skipping whole calibration step< [plustek] >#< [plustek] >option skipCalibration 0< [plustek] Decoding option >skipCalibration< [plustek] >< [plustek] >#< [plustek] ># for skipping entire fine calibration step< [plustek] ># coarse calibration is done< [plustek] >#< [plustek] >option skipFine 0< [plustek] Decoding option >skipFine< [plustek] >< [plustek] >#< [plustek] ># discard the result of the fine white calibration< [plustek] >#< [plustek] >option skipFineWhite 0< [plustek] Decoding option >skipFineWhite< [plustek] >< [plustek] ># for replacing the gain values found during coarse< [plustek] ># calibration< [plustek] ># (can also be set via frontend)< [plustek] >option red_gain -1< [plustek] Decoding option >red_gain< [plustek] >option green_gain -1< [plustek] Decoding option >green_gain< [plustek] >option blue_gain -1< [plustek] Decoding option >blue_gain< [plustek] >< [plustek] ># for replacing the offset values found during coarse< [plustek] ># calibration< [plustek] ># (can also be set via frontend)< [plustek] >option red_offset -1< [plustek] Decoding option >red_offset< [plustek] >option green_offset -1< [plustek] Decoding option >green_offset< [plustek] >option blue_offset -1< [plustek] Decoding option >blue_offset< [plustek] >< [plustek] >#< [plustek] ># for replacing the default lampoff settings, this< [plustek] ># works only for CIS devices like CanoScan LiDE20< [plustek] ># (can also be set via frontend)< [plustek] >option red_lampoff -1< [plustek] Decoding option >red_lampoff< [plustek] >option green_lampoff -1< [plustek] Decoding option >green_lampoff< [plustek] >option blue_lampoff -1< [plustek] Decoding option >blue_lampoff< [plustek] >< [plustek] >#< [plustek] ># for adjusting the default gamma values< [plustek] ># (can also be set via frontend)< [plustek] >option redGamma 1.0< [plustek] Decoding option >redGamma< [plustek] >option greenGamma 1.0< [plustek] Decoding option >greenGamma< [plustek] >option blueGamma 1.0< [plustek] Decoding option >blueGamma< [plustek] >option grayGamma 1.0< [plustek] Decoding option >grayGamma< [plustek] >< [plustek] >#< [plustek] ># to enable TPA (EPSON or UMAX, if autodetection fails)< [plustek] ># 0 means default behaviour as specified in the internal tables< [plustek] ># 1 means enable (needed for UMAX 3450)< [plustek] >option enableTPA 0< [plustek] Decoding option >enableTPA< [plustek] >< [plustek] >#< [plustek] ># model override functionality, currently only available for< [plustek] ># Mustek devices, using NSCs' vendor ID: 0x0400 and< [plustek] ># also their product ID: 0x1000 (LM9831) 0x1001 (LM9832)< [plustek] >#< [plustek] ># mov/PID | 0x1000 | 0x1001< [plustek] ># ---------------------------------------< [plustek] ># 0 (default)| BearPaw1200 | BearPaw 2400< [plustek] ># 1 | ignored | BearPaw 1200< [plustek] >#< [plustek] >option mov 0< [plustek] Decoding option >mov< [plustek] >< [plustek] >#< [plustek] ># and of course the device-name< [plustek] >#< [plustek] ># device /dev/usbscanner< [plustek] >device auto< [plustek] Decoding device name >auto< [plustek] >< [plustek] >#< [plustek] ># to define a new device, start with a new section:< [plustek] ># [usb]< [plustek] >#< [plustek] attach (auto, 0xafd86350, (nil)) [plustek] Device configuration: [plustek] device name : >auto< [plustek] USB-ID : >0x03F0-0x0605< [plustek] model ovr. : 0 [plustek] warmup : -1s [plustek] lampOff : 300 [plustek] lampOffOnEnd : yes [plustek] cacheCalData : no [plustek] altCalibrate : no [plustek] skipCalibr. : no [plustek] skipFine : no [plustek] skipFineWhite: no [plustek] invertNegs. : no [plustek] dis.Speedup : no [plustek] pos_x : 0 [plustek] pos_y : 0 [plustek] pos_shading_y: -1 [plustek] neg_x : 0 [plustek] neg_y : 0 [plustek] neg_shading_y: -1 [plustek] tpa_x : 0 [plustek] tpa_y : 0 [plustek] tpa_shading_y: -1 [plustek] red gain : -1 [plustek] green gain : -1 [plustek] blue gain : -1 [plustek] red offset : -1 [plustek] green offset : -1 [plustek] blue offset : -1 [plustek] red lampoff : -1 [plustek] green lampoff: -1 [plustek] blue lampoff : -1 [plustek] red Gamma : 1.00 [plustek] green Gamma : 1.00 [plustek] blue Gamma : 1.00 [plustek] gray Gamma : 1.00 [plustek] --------------------- [plustek] usbDev_open(auto,0x03F0-0x0605) - 0x806ded8 [plustek] sanei_access_lock failed: 11 [plustek] open failed: -1 [plustek] sane_get_devices (0xafd88478, 0) No scanners were identified. If you were expecting something different, check that the scanner is plugged in, turned on and detected by the sane-find-scanner tool (if appropriate). Please read the documentation which came with this software (README, FAQ, manpages). [plustek] sane_exit root@alexey ~ # grep -v "^#" /etc/sane.d/plustek.conf [usb] 0x03f0 0x0605 option lampOff 300 option warmup -1 option lOffOnEnd 1 option posOffX 0 option posOffY 0 option tpaOffX 0 option tpaOffY 0 option negOffX 0 option negOffY 0 option posShadingY -1 option tpaShadingY -1 option negShadingY -1 option invertNegatives 0 option disableSpeedup 0 option cacheCalData 0 option altCalibration 0 option skipCalibration 0 option skipFine 0 option skipFineWhite 0 option red_gain -1 option green_gain -1 option blue_gain -1 option red_offset -1 option green_offset -1 option blue_offset -1 option red_lampoff -1 option green_lampoff -1 option blue_lampoff -1 option redGamma 1.0 option greenGamma 1.0 option blueGamma 1.0 option grayGamma 1.0 option enableTPA 0 option mov 0 device auto -- С уважением, Алексей Морсов системный администратор ЗАО "ИК "Риком-Траст" ICQ: 196-766-290 Jabber: samurai@www.fondmarket.ru www.ricom.ru www.fondmarket.ru [playing] Yoko Kanno - Cowboy Bebop - Ask DNA Single - AsK DNA (2001) Ставить отдельные пакеты из Сизифа на Мастер 2.4 - верный путь к подрыву системы. Правда, иногда apt'у удаётся это предупредить. -- ktirf in sisyphus@ [-- Attachment #2: Digital signature --] [-- Type: application/pgp-signature, Size: 481 bytes --] ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [sisyphus] hp sj2200c and sane 2006-04-26 7:29 ` Alexey Morsov @ 2006-04-26 20:40 ` Vitaly Lipatov 2006-04-27 8:07 ` Alexey Morsov 0 siblings, 1 reply; 11+ messages in thread From: Vitaly Lipatov @ 2006-04-26 20:40 UTC (permalink / raw) To: ALT Linux Sisyphus discussion list On Wednesday 26 April 2006 11:29, Alexey Morsov wrote: > [plustek] sanei_access_lock failed: 11 > [plustek] open failed: -1 Проблема в невозможности установить блокировку. Покажите $ rpm -q sane $ ls -l /var/lock/sane и # SANE_DEBUG_SANEI_ACCESS=4 scanimage -L -- Lav Виталий Липатов Санкт-Петербург GNU! ALT Linux Team! WINE! LaTeX! LyX! http://freesource.info ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [sisyphus] hp sj2200c and sane 2006-04-26 20:40 ` Vitaly Lipatov @ 2006-04-27 8:07 ` Alexey Morsov 2006-04-27 9:49 ` Anton Farygin 2006-04-27 19:40 ` Vitaly Lipatov 0 siblings, 2 replies; 11+ messages in thread From: Alexey Morsov @ 2006-04-27 8:07 UTC (permalink / raw) To: sisyphus [-- Attachment #1: Type: text/plain, Size: 2536 bytes --] On Thu, Apr 27, 2006 at 12:40:55AM +0400, Vitaly Lipatov wrote: > On Wednesday 26 April 2006 11:29, Alexey Morsov wrote: > > > [plustek] sanei_access_lock failed: 11 > > [plustek] open failed: -1 > Проблема в невозможности установить блокировку. > Покажите > $ rpm -q sane > $ ls -l /var/lock/sane morsov@alexey ~ $ rpm -q sane sane-1.0.17-alt0.1 morsov@alexey ~ $ ls -l /var/lock/sane итого 0 > и > # SANE_DEBUG_SANEI_ACCESS=4 scanimage -L t@alexey ~ # ls -l /var/lock/sane total 0 root@alexey ~ # SANE_DEBUG_SANEI_ACCESS=4 scanimage -L [sanei_debug] Setting debug level of sanei_access to 4. [sanei_access] sanei_access_init: >plustek< [sanei_access] sanei_access_lock: devname >libusb:001:003<, timeout: 5 [sanei_access] sanei_access: lockfile name >/var/lock/sane/sane/LCK..libusb:001:003< [sanei_access] sanei_access_lock: open >/var/lock/sane/sane/LCK..libusb:001:003< failed: No such file or directory Соответственно (не знаю уж почему ее там нет), сделал: root@alexey ~ # mkdir -m 775 /var/lock/sane/sane root@alexey ~ # chown root.scanner /var/lock/sane/sane root@alexey ~ # ls -l /var/lock/sane total 0 drwxrwxr-x 2 root scanner 6 Apr 27 12:05 sane root@alexey ~ # SANE_DEBUG_SANEI_ACCESS=4 scanimage -L [sanei_debug] Setting debug level of sanei_access to 4. [sanei_access] sanei_access_init: >plustek< [sanei_access] sanei_access_lock: devname >libusb:001:003<, timeout: 5 [sanei_access] sanei_access: lockfile name >/var/lock/sane/sane/LCK..libusb:001:003< [sanei_access] sanei_access_lock: success [sanei_access] sanei_access_unlock: devname >libusb:001:003< [sanei_access] sanei_access: lockfile name >/var/lock/sane/sane/LCK..libusb:001:003< [sanei_access] sanei_access_unlock: devname >libusb:001:003< [sanei_access] sanei_access: lockfile name >/var/lock/sane/sane/LCK..libusb:001:003< device `plustek:libusb:001:003' is a Hewlett-Packard Scanjet 2200c USB flatbed scanner Теперь снова все работает. Спасибо. Это у меня такая бяка была или это кто-то чего-то недосоздал (багу вешать)? -- С уважением, Алексей Морсов системный администратор ЗАО "ИК "Риком-Траст" ICQ: 196-766-290 Jabber: samurai@www.fondmarket.ru www.ricom.ru www.fondmarket.ru [playing] Yoko Kanno - Cowboy Bebop - Ask DNA Single - COSMIC DARE (PRETTY WITH A PISTOL) (2001) > Но дам неплохой совет - прежде чем тестировать патчи нужно > вытащить mysql из chroot... Но прежде чем использовать - втащить обратно в чрут. -- ldv in sisyphus@ [-- Attachment #2: Digital signature --] [-- Type: application/pgp-signature, Size: 481 bytes --] ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [sisyphus] hp sj2200c and sane 2006-04-27 8:07 ` Alexey Morsov @ 2006-04-27 9:49 ` Anton Farygin 2006-04-27 10:37 ` Alexey Morsov 2006-04-27 19:40 ` Vitaly Lipatov 1 sibling, 1 reply; 11+ messages in thread From: Anton Farygin @ 2006-04-27 9:49 UTC (permalink / raw) To: sisyphus Alexey Morsov wrote: > On Thu, Apr 27, 2006 at 12:40:55AM +0400, Vitaly Lipatov wrote: >> On Wednesday 26 April 2006 11:29, Alexey Morsov wrote: >> >>> [plustek] sanei_access_lock failed: 11 >>> [plustek] open failed: -1 >> Проблема в невозможности установить блокировку. >> Покажите >> $ rpm -q sane > >> $ ls -l /var/lock/sane > morsov@alexey ~ $ rpm -q sane > sane-1.0.17-alt0.1 > morsov@alexey ~ $ ls -l /var/lock/sane > итого 0 > >> и >> # SANE_DEBUG_SANEI_ACCESS=4 scanimage -L > > t@alexey ~ # ls -l /var/lock/sane > total 0 > root@alexey ~ # SANE_DEBUG_SANEI_ACCESS=4 scanimage -L > [sanei_debug] Setting debug level of sanei_access to 4. > [sanei_access] sanei_access_init: >plustek< > [sanei_access] sanei_access_lock: devname >libusb:001:003<, timeout: 5 > [sanei_access] sanei_access: lockfile name >/var/lock/sane/sane/LCK..libusb:001:003< > [sanei_access] sanei_access_lock: open >/var/lock/sane/sane/LCK..libusb:001:003< failed: No such file or directory > > Соответственно (не знаю уж почему ее там нет), сделал: > > root@alexey ~ # mkdir -m 775 /var/lock/sane/sane > root@alexey ~ # chown root.scanner /var/lock/sane/sane > root@alexey ~ # ls -l /var/lock/sane > total 0 > drwxrwxr-x 2 root scanner 6 Apr 27 12:05 sane > root@alexey ~ # SANE_DEBUG_SANEI_ACCESS=4 scanimage -L > [sanei_debug] Setting debug level of sanei_access to 4. > [sanei_access] sanei_access_init: >plustek< > [sanei_access] sanei_access_lock: devname >libusb:001:003<, timeout: 5 > [sanei_access] sanei_access: lockfile name >/var/lock/sane/sane/LCK..libusb:001:003< > [sanei_access] sanei_access_lock: success > [sanei_access] sanei_access_unlock: devname >libusb:001:003< > [sanei_access] sanei_access: lockfile name >/var/lock/sane/sane/LCK..libusb:001:003< > [sanei_access] sanei_access_unlock: devname >libusb:001:003< > [sanei_access] sanei_access: lockfile name >/var/lock/sane/sane/LCK..libusb:001:003< > device `plustek:libusb:001:003' is a Hewlett-Packard Scanjet 2200c USB flatbed scanner > > Теперь снова все работает. Спасибо. > Это у меня такая бяка была или это кто-то чего-то недосоздал (багу вешать)? Вешать багу. Rgds, Rider ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [sisyphus] hp sj2200c and sane 2006-04-27 9:49 ` Anton Farygin @ 2006-04-27 10:37 ` Alexey Morsov 2006-04-27 11:16 ` Anton Farygin 0 siblings, 1 reply; 11+ messages in thread From: Alexey Morsov @ 2006-04-27 10:37 UTC (permalink / raw) To: sisyphus [-- Attachment #1: Type: text/plain, Size: 537 bytes --] On Thu, Apr 27, 2006 at 01:49:52PM +0400, Anton Farygin wrote: > Вешать багу. Хотелось бы уточнитьна кого? На sane или libsane ? -- С уважением, Алексей Морсов системный администратор ЗАО "ИК "Риком-Траст" ICQ: 196-766-290 Jabber: samurai@www.fondmarket.ru www.ricom.ru www.fondmarket.ru [paused] Yoko Kanno - Cowboy Bebop: Vitaminless - Doggy Dog () > Кстати, а зачем нам вообще ещё нужен 2.9x в Сизифе? > Может выкинуть их вообще? Хотя бы затем, чтобы не забыть про проблему с apt'ом. :) -- ldv in devel@ [-- Attachment #2: Digital signature --] [-- Type: application/pgp-signature, Size: 481 bytes --] ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [sisyphus] hp sj2200c and sane 2006-04-27 10:37 ` Alexey Morsov @ 2006-04-27 11:16 ` Anton Farygin 2006-04-27 14:50 ` Alexey Morsov 0 siblings, 1 reply; 11+ messages in thread From: Anton Farygin @ 2006-04-27 11:16 UTC (permalink / raw) To: sisyphus Alexey Morsov wrote: > On Thu, Apr 27, 2006 at 01:49:52PM +0400, Anton Farygin wrote: >> Вешать багу. > Хотелось бы уточнитьна кого? > На sane или libsane ? Явно на libsane Rgds, Rider ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [sisyphus] hp sj2200c and sane 2006-04-27 11:16 ` Anton Farygin @ 2006-04-27 14:50 ` Alexey Morsov 0 siblings, 0 replies; 11+ messages in thread From: Alexey Morsov @ 2006-04-27 14:50 UTC (permalink / raw) To: sisyphus [-- Attachment #1: Type: text/plain, Size: 597 bytes --] On Thu, Apr 27, 2006 at 03:16:36PM +0400, Anton Farygin wrote: > Явно на libsane #9481 -- С уважением, Алексей Морсов системный администратор ЗАО "ИК "Риком-Траст" ICQ: 196-766-290 Jabber: samurai@www.fondmarket.ru www.ricom.ru www.fondmarket.ru [playing] Yoko Kanno - Cowboy Bebop - Ask DNA Single - AsK DNA (2001) > [...] использовать в пакетах /etc/ld.so.conf.d/ ВМЕСТО > традиционных записей в /etc/ld.so.conf пока рано. Ok. Некоторые из нас уже успели заиспользовать "ВМЕСТО" эту функциональность. В связи с этим ждите новую сборку XFree86. -- rider in devel@ [-- Attachment #2: Digital signature --] [-- Type: application/pgp-signature, Size: 481 bytes --] ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [sisyphus] hp sj2200c and sane 2006-04-27 8:07 ` Alexey Morsov 2006-04-27 9:49 ` Anton Farygin @ 2006-04-27 19:40 ` Vitaly Lipatov 2006-04-28 8:17 ` Alexey Morsov 1 sibling, 1 reply; 11+ messages in thread From: Vitaly Lipatov @ 2006-04-27 19:40 UTC (permalink / raw) To: ALT Linux Sisyphus discussion list On Thursday 27 April 2006 12:07, Alexey Morsov wrote: > On Thu, Apr 27, 2006 at 12:40:55AM +0400, Vitaly Lipatov wrote: > > On Wednesday 26 April 2006 11:29, Alexey Morsov wrote: > > > [plustek] sanei_access_lock failed: 11 > > > [plustek] open failed: -1 > > > > Проблема в невозможности установить блокировку. > > Покажите > > $ rpm -q sane > > > > $ ls -l /var/lock/sane > > morsov@alexey ~ $ rpm -q sane > sane-1.0.17-alt0.1 ... > Теперь снова все работает. Спасибо. > Это у меня такая бяка была или это кто-то чего-то недосоздал > (багу вешать)? У вас старый sane, в Сизифе уже 2 месяца как всё исправлено. -- Lav Виталий Липатов Санкт-Петербург GNU! ALT Linux Team! WINE! LaTeX! LyX! http://freesource.info ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [sisyphus] hp sj2200c and sane 2006-04-27 19:40 ` Vitaly Lipatov @ 2006-04-28 8:17 ` Alexey Morsov 0 siblings, 0 replies; 11+ messages in thread From: Alexey Morsov @ 2006-04-28 8:17 UTC (permalink / raw) To: sisyphus [-- Attachment #1: Type: text/plain, Size: 627 bytes --] On Thu, Apr 27, 2006 at 11:40:15PM +0400, Vitaly Lipatov wrote: > У вас старый sane, в Сизифе уже 2 месяца как всё исправлено. Слава богу если так. А при dist-update таки он бы поправил бы пути к lock файлу (ведь пакет уже стоит)? -- С уважением, Алексей Морсов системный администратор ЗАО "ИК "Риком-Траст" ICQ: 196-766-290 Jabber: samurai@www.fondmarket.ru www.ricom.ru www.fondmarket.ru [playing] Yoko Kanno - Cowboy Bebop - Tank! THE! BEST! - PIANO BLACK (2004) > Штатно - vmware-config.pl не видит хидеров штатно - использовать kernel-modules-vmware от wrar@ -- lakostis in devel-kernel@ [-- Attachment #2: Digital signature --] [-- Type: application/pgp-signature, Size: 481 bytes --] ^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2006-04-28 8:17 UTC | newest] Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2006-04-25 9:05 [sisyphus] hp sj2200c and sane Alexey Morsov 2006-04-25 19:11 ` Vitaly Lipatov 2006-04-26 7:29 ` Alexey Morsov 2006-04-26 20:40 ` Vitaly Lipatov 2006-04-27 8:07 ` Alexey Morsov 2006-04-27 9:49 ` Anton Farygin 2006-04-27 10:37 ` Alexey Morsov 2006-04-27 11:16 ` Anton Farygin 2006-04-27 14:50 ` Alexey Morsov 2006-04-27 19:40 ` Vitaly Lipatov 2006-04-28 8:17 ` Alexey Morsov
ALT Linux Sisyphus discussions This inbox may be cloned and mirrored by anyone: git clone --mirror http://lore.altlinux.org/sisyphus/0 sisyphus/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 sisyphus sisyphus/ http://lore.altlinux.org/sisyphus \ sisyphus@altlinux.ru sisyphus@altlinux.org sisyphus@lists.altlinux.org sisyphus@lists.altlinux.ru sisyphus@lists.altlinux.com sisyphus@linuxteam.iplabs.ru sisyphus@list.linux-os.ru public-inbox-index sisyphus Example config snippet for mirrors. Newsgroup available over NNTP: nntp://lore.altlinux.org/org.altlinux.lists.sisyphus AGPL code for this site: git clone https://public-inbox.org/public-inbox.git