* Re: [sisyphus] Драйвер для DWL-G520+ @ 2005-05-04 19:26 ` Vitaly Smirnov 2005-05-04 19:36 ` Vitaly Smirnov 1 sibling, 0 replies; 6+ messages in thread From: Vitaly Smirnov @ 2005-05-04 19:26 UTC (permalink / raw) To: ALT Linux Sisyphus discussion list Roman Savochenko пишет: > Vitaly Smirnov пишет: > >>>> Спасибо за пакеты. Однако есть проблемы: - нестыковка с >>>> версией пакета и именем директории пакета >>>> kernel-source-acx100-0.2.0pre8_plus_fixes_54-alt1.src.rpm - >>>> он у вас точно собирался на 2.4.26? У меня ругается, причём >>>> на двух машинах, таким образом: >>>> >> В plus_fixes54 что-то сломали и оно теперь не собиарется на ветке >> 2.4. Однако plus_fixes49 прекрасно собралось на >> 2.4.29-alt3-std-up. З0бирайте ;) >> http://www.geeks.ru/alt/kernel-source-acx100-0.2.0pre8_plus_fixes_49-alt1.src.rpm >> >> >> http://www.geeks.ru/alt/kernel-modules-acx100-std-up-0.2.0pre8_plus_fixes_49-alt1.src.rpm >> >> > > > Большое спасибо! Однако всё равно пришлось на ядре 2.6.8 поднимать. > На 2.4.26 соединяется но нет передачи и гонит ошибки с по > прерыванию. На 2.6.8 завелось но потом тоже слитело с сообщениями > типа: > Не знаю, у меня прекрасно работает сервер с DWL-G520+ на 2.4.29 ядре уже как пол года, проблем не наблюдалось, разве что пару раз вылетало сообщение о превышении мощности и приходилось перезагружать драйвер. Проверьте, то ли firmware вы скопировали, и скопировали ли его всё. > Кстати, при остановке wlan система виснит намертво. Да, по поводу > запуска. Чем вы его пускаете? # modprobe acx_pci или в /etc/modules.conf alias wlan0 acx_pci Крайне советую Вам перечитать документацию и включить дебаг, возможно проблема всплывёт. -- С уважением, Виталий Смирнов. ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [sisyphus] Драйвер для DWL-G520+ 2005-05-04 19:26 ` [sisyphus] Драйвер для DWL-G520+ Vitaly Smirnov @ 2005-05-04 19:36 ` Vitaly Smirnov 2005-05-05 5:45 ` Roman Savochenko 1 sibling, 1 reply; 6+ messages in thread From: Vitaly Smirnov @ 2005-05-04 19:36 UTC (permalink / raw) To: ALT Linux Sisyphus discussion list Roman Savochenko пишет: > Vitaly Smirnov пишет: > >>>> Спасибо за пакеты. Однако есть проблемы: - нестыковка с >>>> версией пакета и именем директории пакета >>>> kernel-source-acx100-0.2.0pre8_plus_fixes_54-alt1.src.rpm - >>>> он у вас точно собирался на 2.4.26? У меня ругается, причём >>>> на двух машинах, таким образом: >>>> >> В plus_fixes54 что-то сломали и оно теперь не собиарется на ветке >> 2.4. Однако plus_fixes49 прекрасно собралось на >> 2.4.29-alt3-std-up. З0бирайте ;) >> http://www.geeks.ru/alt/kernel-source-acx100-0.2.0pre8_plus_fixes_49-alt1.src.rpm >> >> >> http://www.geeks.ru/alt/kernel-modules-acx100-std-up-0.2.0pre8_plus_fixes_49-alt1.src.rpm >> >> > > > Большое спасибо! Однако всё равно пришлось на ядре 2.6.8 поднимать. > На 2.4.26 соединяется но нет передачи и гонит ошибки с по > прерыванию. На 2.6.8 завелось но потом тоже слитело с сообщениями > типа: > Не знаю, у меня прекрасно работает сервер с DWL-G520+ на 2.4.29 ядре уже как пол года, проблем не наблюдалось, разве что пару раз вылетало сообщение о превышении мощности и приходилось перезагружать драйвер. Проверьте, то ли firmware вы скопировали, и скопировали ли его всё. > Кстати, при остановке wlan система виснит намертво. Да, по поводу > запуска. Чем вы его пускаете? # modprobe acx_pci или в /etc/modules.conf alias wlan0 acx_pci Крайне советую Вам перечитать документацию и включить дебаг, возможно проблема всплывёт. -- С уважением, Виталий Смирнов. ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [sisyphus] Драйвер для DWL-G520+ 2005-05-04 19:36 ` Vitaly Smirnov @ 2005-05-05 5:45 ` Roman Savochenko 2005-05-05 9:13 ` Vitaly Smirnov 0 siblings, 1 reply; 6+ messages in thread From: Roman Savochenko @ 2005-05-05 5:45 UTC (permalink / raw) To: ALT Linux Sisyphus discussion list Vitaly Smirnov пишет: >>>>>Спасибо за пакеты. Однако есть проблемы: - нестыковка с >>>>>версией пакета и именем директории пакета >>>>>kernel-source-acx100-0.2.0pre8_plus_fixes_54-alt1.src.rpm - >>>>>он у вас точно собирался на 2.4.26? У меня ругается, причём >>>>>на двух машинах, таким образом: >>>>> >>> >>>В plus_fixes54 что-то сломали и оно теперь не собиарется на ветке >>>2.4. Однако plus_fixes49 прекрасно собралось на >>>2.4.29-alt3-std-up. З0бирайте ;) > http://www.geeks.ru/alt/kernel-source-acx100-0.2.0pre8_plus_fixes_49-alt1.src.rpm > http://www.geeks.ru/alt/kernel-modules-acx100-std-up-0.2.0pre8_plus_fixes_49-alt1.src.rpm >>Большое спасибо! Однако всё равно пришлось на ядре 2.6.8 поднимать. >>На 2.4.26 соединяется но нет передачи и гонит ошибки с по >>прерыванию. На 2.6.8 завелось но потом тоже слитело с сообщениями >>типа: >> > > Не знаю, у меня прекрасно работает сервер с DWL-G520+ на 2.4.29 ядре > уже как пол года, проблем не наблюдалось, разве что пару раз вылетало > сообщение о превышении мощности и приходилось перезагружать драйвер. > Проверьте, то ли firmware вы скопировали, и скопировали ли его всё. Я брал из диска с дровами для Win. Переименовал в TIACX111.BIN. А вы откуда брали? >>Кстати, при остановке wlan система виснит намертво. Да, по поводу >>запуска. Чем вы его пускаете? > # modprobe acx_pci > или в /etc/modules.conf alias wlan0 acx_pci А опции как грузите? Ну там всякие: IP, ESID, KEY, .... > Крайне советую Вам перечитать документацию и включить дебаг, возможно > проблема всплывёт. В смысле, прочитать вдумчиво. :) С уважением Роман! ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [sisyphus] Драйвер для DWL-G520+ 2005-05-05 5:45 ` Roman Savochenko @ 2005-05-05 9:13 ` Vitaly Smirnov 2005-05-06 6:42 ` Roman Savochenko 0 siblings, 1 reply; 6+ messages in thread From: Vitaly Smirnov @ 2005-05-05 9:13 UTC (permalink / raw) To: ALT Linux Sisyphus discussion list Roman Savochenko пишет: > Vitaly Smirnov пишет: > >>>>>> Спасибо за пакеты. Однако есть проблемы: - нестыковка с >>>>>> версией пакета и именем директории пакета >>>>>> kernel-source-acx100-0.2.0pre8_plus_fixes_54-alt1.src.rpm >>>>>> - он у вас точно собирался на 2.4.26? У меня ругается, >>>>>> причём на двух машинах, таким образом: >>>>>> >>>> >>>> В plus_fixes54 что-то сломали и оно теперь не собиарется на >>>> ветке 2.4. Однако plus_fixes49 прекрасно собралось на >>>> 2.4.29-alt3-std-up. З0бирайте ;) >> >> http://www.geeks.ru/alt/kernel-source-acx100-0.2.0pre8_plus_fixes_49-alt1.src.rpm >> >> >> http://www.geeks.ru/alt/kernel-modules-acx100-std-up-0.2.0pre8_plus_fixes_49-alt1.src.rpm >> >> >> >>> Большое спасибо! Однако всё равно пришлось на ядре 2.6.8 >>> поднимать. На 2.4.26 соединяется но нет передачи и гонит ошибки >>> с по прерыванию. На 2.6.8 завелось но потом тоже слитело с >>> сообщениями типа: >>> >> >> Не знаю, у меня прекрасно работает сервер с DWL-G520+ на 2.4.29 >> ядре уже как пол года, проблем не наблюдалось, разве что пару раз >> вылетало сообщение о превышении мощности и приходилось >> перезагружать драйвер. Проверьте, то ли firmware вы скопировали, >> и скопировали ли его всё. > > > Я брал из диска с дровами для Win. Переименовал в TIACX111.BIN. А > вы откуда брали? > Тоже с диска, только ничего не переименовывал, чего и Вам советую. (там было два файла, один bin один ещё что-то, что именно - уже не помню. Скопируйте оба.) >>> Кстати, при остановке wlan система виснит намертво. Да, по >>> поводу запуска. Чем вы его пускаете? >> >> # modprobe acx_pci или в /etc/modules.conf alias wlan0 acx_pci > > > А опции как грузите? Ну там всякие: IP, ESID, KEY, .... > iwconfig и компания. >> Крайне советую Вам перечитать документацию и включить дебаг, >> возможно проблема всплывёт. > > > В смысле, прочитать вдумчиво. :) Именно это и имелось в виду :-) ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [sisyphus] Драйвер для DWL-G520+ 2005-05-05 9:13 ` Vitaly Smirnov @ 2005-05-06 6:42 ` Roman Savochenko 2005-05-06 6:51 ` Vitaly Smirnov 0 siblings, 1 reply; 6+ messages in thread From: Roman Savochenko @ 2005-05-06 6:42 UTC (permalink / raw) To: ALT Linux Sisyphus discussion list Vitaly Smirnov пишет: >>>>>>>Спасибо за пакеты. Однако есть проблемы: - нестыковка с >>>>>>>версией пакета и именем директории пакета >>>>>>>kernel-source-acx100-0.2.0pre8_plus_fixes_54-alt1.src.rpm >>>>>>>- он у вас точно собирался на 2.4.26? У меня ругается, >>>>>>>причём на двух машинах, таким образом: >>>>>В plus_fixes54 что-то сломали и оно теперь не собиарется на >>>>>ветке 2.4. Однако plus_fixes49 прекрасно собралось на >>>>>2.4.29-alt3-std-up. З0бирайте ;) > http://www.geeks.ru/alt/kernel-source-acx100-0.2.0pre8_plus_fixes_49-alt1.src.rpm > http://www.geeks.ru/alt/kernel-modules-acx100-std-up-0.2.0pre8_plus_fixes_49-alt1.src.rpm >>>>Большое спасибо! Однако всё равно пришлось на ядре 2.6.8 >>>>поднимать. На 2.4.26 соединяется но нет передачи и гонит ошибки >>>>с по прерыванию. На 2.6.8 завелось но потом тоже слитело с >>>>сообщениями типа: >>>Не знаю, у меня прекрасно работает сервер с DWL-G520+ на 2.4.29 >>>ядре уже как пол года, проблем не наблюдалось, разве что пару раз >>>вылетало сообщение о превышении мощности и приходилось >>>перезагружать драйвер. Проверьте, то ли firmware вы скопировали, >>>и скопировали ли его всё. Вроде работает. Однако при попытке выгрузить модуль, после соединения, устойчиво вешает систему. Вы не пробывали выгружать модуль? >>Я брал из диска с дровами для Win. Переименовал в TIACX111.BIN. А >>вы откуда брали? > Тоже с диска, только ничего не переименовывал, чего и Вам советую. > (там было два файла, один bin один ещё что-то, что именно - уже не > помню. Скопируйте оба.) Доки говорят, что ему нужен именно TIACX111.BIN. >>>>Кстати, при остановке wlan система виснит намертво. Да, по >>>>поводу запуска. Чем вы его пускаете? >>># modprobe acx_pci или в /etc/modules.conf alias wlan0 acx_pci >>А опции как грузите? Ну там всякие: IP, ESID, KEY, .... > iwconfig и компания. А автоматизировать? :) С уважением Роман! ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [sisyphus] Драйвер для DWL-G520+ 2005-05-06 6:42 ` Roman Savochenko @ 2005-05-06 6:51 ` Vitaly Smirnov 0 siblings, 0 replies; 6+ messages in thread From: Vitaly Smirnov @ 2005-05-06 6:51 UTC (permalink / raw) To: ALT Linux Sisyphus discussion list Roman Savochenko пишет: > Вроде работает. Однако при попытке выгрузить модуль, после > соединения, устойчиво вешает систему. Вы не пробывали выгружать > модуль? > Выгружал и не раз, работает стабильно. Надеюсь вы не забыли опустить интерфейс перед выгружением драйвера? ifconfig wlan0 down > Доки говорят, что ему нужен именно TIACX111.BIN. > Доки это хорошо, но всё же попробуйте сделать так, как я Вам предложил. >>> А опции как грузите? Ну там всякие: IP, ESID, KEY, .... >> >> iwconfig и компания. > > А автоматизировать? :) Добавить /etc/sysconfig/network-scripts/ifcfg-wlan0 с необходимыми параметрами. За синтаксисом в доку. ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2005-05-06 6:51 UTC | newest] Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2005-05-04 19:26 ` [sisyphus] Драйвер для DWL-G520+ Vitaly Smirnov 2005-05-04 19:36 ` Vitaly Smirnov 2005-05-05 5:45 ` Roman Savochenko 2005-05-05 9:13 ` Vitaly Smirnov 2005-05-06 6:42 ` Roman Savochenko 2005-05-06 6:51 ` Vitaly Smirnov
ALT Linux Sisyphus discussions This inbox may be cloned and mirrored by anyone: git clone --mirror http://lore.altlinux.org/sisyphus/0 sisyphus/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 sisyphus sisyphus/ http://lore.altlinux.org/sisyphus \ sisyphus@altlinux.ru sisyphus@altlinux.org sisyphus@lists.altlinux.org sisyphus@lists.altlinux.ru sisyphus@lists.altlinux.com sisyphus@linuxteam.iplabs.ru sisyphus@list.linux-os.ru public-inbox-index sisyphus Example config snippet for mirrors. Newsgroup available over NNTP: nntp://lore.altlinux.org/org.altlinux.lists.sisyphus AGPL code for this site: git clone https://public-inbox.org/public-inbox.git