* [sisyphus] Cups и HP LazerJet 1018 @ 2007-09-12 13:15 Nikolay 2007-09-12 13:24 ` Motsyo Gennadi aka Drool 0 siblings, 1 reply; 25+ messages in thread From: Nikolay @ 2007-09-12 13:15 UTC (permalink / raw) To: sisyphus Доброго дня. При попытке запустить HP LazerJet 1018 с сегодняшним сизифом получаю нерабочую систему - выражается в том что задания ставятся и печатаются - печатаются в никуда - принтер молчит. lpq выводит список - и через некоторое время показывает пустой. В логах /var/log/messages При попытке hp-setup Sep 12 17:56:48 term python: hp-setup[2875]: error: Device busy: hp:/usb/HP_LaserJet_1018?serial=KP1NXX3 Sep 12 17:56:48 term python: hp-setup[2875]: error: Unable to print to printer.Please check device and try again. Устройств он не видит - если руками указать - то определяет нормально. При печати ... Sep 12 17:58:43 term kernel: lp0: using parport0 (interrupt-driven). Sep 12 17:58:43 term kernel: lp0: console ready Sep 12 17:58:56 term hpijs: WARNING: printmode mismatch with pen, tray, etc. Sep 12 17:58:56 term hpijs: STATE: -marker-supply-low-warning Sep 12 17:58:56 term HP_LaserJet_1018?serial=KP1NXX3: INFO: Printing... Sep 12 18:05:47 term HP_LaserJet_1018?serial=KP1NXX3: INFO: Printing... Собственно printers.conf <Printer 1> Info HP LaserJet Location 1 DeviceURI hp:/usb/HP_LaserJet_1018?serial=KP1NXX3 State Stopped StateMessage Paused StateTime 1189610142 Accepting Yes Shared Yes JobSheets none none QuotaPeriod 0 PageLimit 0 KLimit 0 OpPolicy default ErrorPolicy stop-printer </Printer> Подскажите пожалуйста - где я собственно не прав ? -- С уважением, Николай ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-12 13:15 [sisyphus] Cups и HP LazerJet 1018 Nikolay @ 2007-09-12 13:24 ` Motsyo Gennadi aka Drool 2007-09-12 13:27 ` Nikolay 0 siblings, 1 reply; 25+ messages in thread From: Motsyo Gennadi aka Drool @ 2007-09-12 13:24 UTC (permalink / raw) To: ALT Linux Sisyphus discussions Nikolay пишет: > Доброго дня. > При попытке запустить HP LazerJet 1018 с сегодняшним сизифом получаю > нерабочую систему - выражается в том что задания ставятся и печатаются - > печатаются в никуда - принтер молчит. А этому принтеру случайно не нужно подкидывать firmware? На 1015 я подкидывал... И специальный драйвер с непроизносимым названием для него установлен? ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-12 13:24 ` Motsyo Gennadi aka Drool @ 2007-09-12 13:27 ` Nikolay 2007-09-12 13:40 ` Андрей Черепанов 0 siblings, 1 reply; 25+ messages in thread From: Nikolay @ 2007-09-12 13:27 UTC (permalink / raw) To: ALT Linux Sisyphus discussions В сообщении от 12 сентября 2007 Motsyo Gennadi aka Drool написал(a): > Nikolay пишет: > > Доброго дня. > > При попытке запустить HP LazerJet 1018 с сегодняшним сизифом получаю > > нерабочую систему - выражается в том что задания ставятся и печатаются - > > печатаются в никуда - принтер молчит. > > А этому принтеру случайно не нужно подкидывать firmware? На 1015 я > подкидывал... И специальный драйвер с непроизносимым названием для него > установлен? Если можно - опишите пожалуйста процесс. - рядом похожий 1010 посети работает на ура. :( -- С уважением, Николай ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-12 13:27 ` Nikolay @ 2007-09-12 13:40 ` Андрей Черепанов 2007-09-12 13:58 ` Nikolay 2007-09-12 14:19 ` Евгений 0 siblings, 2 replies; 25+ messages in thread From: Андрей Черепанов @ 2007-09-12 13:40 UTC (permalink / raw) To: ALT Linux Sisyphus discussions 12 сентября 2007 Nikolay написал: > В сообщении от 12 сентября 2007 Motsyo Gennadi aka Drool написал(a): > > Nikolay пишет: > > > Доброго дня. > > > При попытке запустить HP LazerJet 1018 с сегодняшним сизифом получаю > > > нерабочую систему - выражается в том что задания ставятся и печатаются > > > - печатаются в никуда - принтер молчит. > > > > А этому принтеру случайно не нужно подкидывать firmware? На 1015 я > > подкидывал... И специальный драйвер с непроизносимым названием для него > > установлен? > > Если можно - опишите пожалуйста процесс. > - рядом похожий 1010 посети работает на ура. :( Кстати, если подключить к Linux HP 1010 напрямую из-за кривого firmware на борту принтера через 3-5 заданий он прекращает печатать. -- Андрей Черепанов ALT Linux Solutions cas@altlinux.ru ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-12 13:40 ` Андрей Черепанов @ 2007-09-12 13:58 ` Nikolay 2007-09-12 14:23 ` Евгений 2007-09-12 14:19 ` Евгений 1 sibling, 1 reply; 25+ messages in thread From: Nikolay @ 2007-09-12 13:58 UTC (permalink / raw) To: ALT Linux Sisyphus discussions В сообщении от 12 сентября 2007 Андрей Черепанов написал(a): > 12 сентября 2007 Nikolay написал: > > В сообщении от 12 сентября 2007 Motsyo Gennadi aka Drool написал(a): > > > Nikolay пишет: > > > > Доброго дня. > > > > При попытке запустить HP LazerJet 1018 с сегодняшним сизифом получаю > > > > нерабочую систему - выражается в том что задания ставятся и > > > > печатаются - печатаются в никуда - принтер молчит. > > > > > > А этому принтеру случайно не нужно подкидывать firmware? На 1015 я > > > подкидывал... И специальный драйвер с непроизносимым названием для него > > > установлен? Спасибо !!! - установка foo2zjs помогла. -- С уважением, Николай ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-12 13:58 ` Nikolay @ 2007-09-12 14:23 ` Евгений 2007-09-12 14:26 ` Nikolay 2007-09-16 19:46 ` Michael Shigorin 0 siblings, 2 replies; 25+ messages in thread From: Евгений @ 2007-09-12 14:23 UTC (permalink / raw) To: ALT Linux Sisyphus discussions Nikolay пишет: > В сообщении от 12 сентября 2007 Андрей Черепанов написал(a): >> 12 сентября 2007 Nikolay написал: >>> В сообщении от 12 сентября 2007 Motsyo Gennadi aka Drool написал(a): >>>> Nikolay пишет: >>>>> Доброго дня. >>>>> При попытке запустить HP LazerJet 1018 с сегодняшним сизифом получаю >>>>> нерабочую систему - выражается в том что задания ставятся и >>>>> печатаются - печатаются в никуда - принтер молчит. >>>> А этому принтеру случайно не нужно подкидывать firmware? На 1015 я >>>> подкидывал... И специальный драйвер с непроизносимым названием для него >>>> установлен? > Спасибо !!! - установка foo2zjs помогла. Да, вот только пересобрать бы его (foo2zjs). С текущим foomatic конфликт поймал по поводу hp1022. Похоже в foomatic для этого принтера драйвера появились, а foo2zjs конфликтует. ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-12 14:23 ` Евгений @ 2007-09-12 14:26 ` Nikolay 2007-09-13 4:24 ` Шишков Евгений 2007-09-16 19:46 ` Michael Shigorin 1 sibling, 1 reply; 25+ messages in thread From: Nikolay @ 2007-09-12 14:26 UTC (permalink / raw) To: ALT Linux Sisyphus discussions В сообщении от 12 сентября 2007 Евгений написал(a): > > Да, вот только пересобрать бы его (foo2zjs). С текущим foomatic конфликт > поймал по поводу hp1022. Похоже в foomatic для этого принтера драйвера > появились, а foo2zjs конфликтует. Да мне пришлось снести foomatic-db и зависимости его . -- С уважением, Николай ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-12 14:26 ` Nikolay @ 2007-09-13 4:24 ` Шишков Евгений 0 siblings, 0 replies; 25+ messages in thread From: Шишков Евгений @ 2007-09-13 4:24 UTC (permalink / raw) To: ALT Linux Sisyphus discussions Nikolay пишет: > В сообщении от 12 сентября 2007 Евгений написал(a): > >> Да, вот только пересобрать бы его (foo2zjs). С текущим foomatic конфликт >> поймал по поводу hp1022. Похоже в foomatic для этого принтера драйвера >> появились, а foo2zjs конфликтует. > Да мне пришлось снести foomatic-db и зависимости его . Мне тоже. ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-12 14:23 ` Евгений 2007-09-12 14:26 ` Nikolay @ 2007-09-16 19:46 ` Michael Shigorin 1 sibling, 0 replies; 25+ messages in thread From: Michael Shigorin @ 2007-09-16 19:46 UTC (permalink / raw) To: ALT Linux Sisyphus discussions On Wed, Sep 12, 2007 at 06:23:53PM +0400, Евгений wrote: > > Спасибо !!! - установка foo2zjs помогла. > Да, вот только пересобрать бы его (foo2zjs). С текущим foomatic > конфликт поймал по поводу hp1022. Похоже в foomatic для этого > принтера драйвера появились, а foo2zjs конфликтует. Сейчас попробую добраться наконец. Там вечный кайф с кочеванием драйверов из откуда ни возьмись в foomatic, причём для случая, когда всё равно для этих .ppd нужен пакет со специфическим драйвером, я не уверен в правильности такого переноса. Но "принято"(c) переносить, поскольку никто пока это всё обдумать не добрался. [#12749 fixed] -- ---- WBR, Michael Shigorin <mike@altlinux.ru> ------ Linux.Kiev http://www.linux.kiev.ua/ ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-12 13:40 ` Андрей Черепанов 2007-09-12 13:58 ` Nikolay @ 2007-09-12 14:19 ` Евгений 2007-09-16 19:47 ` Michael Shigorin 2007-09-18 9:10 ` Nikolay 1 sibling, 2 replies; 25+ messages in thread From: Евгений @ 2007-09-12 14:19 UTC (permalink / raw) To: ALT Linux Sisyphus discussions Андрей Черепанов пишет: > 12 сентября 2007 Nikolay написал: >> В сообщении от 12 сентября 2007 Motsyo Gennadi aka Drool написал(a): >>> Nikolay пишет: >>>> Доброго дня. >>>> При попытке запустить HP LazerJet 1018 с сегодняшним сизифом получаю >>>> нерабочую систему - выражается в том что задания ставятся и печатаются >>>> - печатаются в никуда - принтер молчит. >>> А этому принтеру случайно не нужно подкидывать firmware? На 1015 я >>> подкидывал... И специальный драйвер с непроизносимым названием для него >>> установлен? >> Если можно - опишите пожалуйста процесс. >> - рядом похожий 1010 посети работает на ура. :( > Кстати, если подключить к Linux HP 1010 напрямую из-за кривого firmware на > борту принтера через 3-5 заданий он прекращает печатать. Не подтверждаю. Прекрасно работает. В работе HP 1010,1015,1018,1022. ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-12 14:19 ` Евгений @ 2007-09-16 19:47 ` Michael Shigorin 2007-09-18 9:10 ` Nikolay 1 sibling, 0 replies; 25+ messages in thread From: Michael Shigorin @ 2007-09-16 19:47 UTC (permalink / raw) To: ALT Linux Sisyphus discussions On Wed, Sep 12, 2007 at 06:19:31PM +0400, Евгений wrote: > Прекрасно работает. В работе HP 1010,1015,1018,1022. Евгений, если вдруг созреете майнтейнить пакет -- черкните, мне его сейчас тестить не на чем, а собиралось с поддержкой нужного HP10xx из одесского представительства заказчика полтора года тому :) -- ---- WBR, Michael Shigorin <mike@altlinux.ru> ------ Linux.Kiev http://www.linux.kiev.ua/ ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-12 14:19 ` Евгений 2007-09-16 19:47 ` Michael Shigorin @ 2007-09-18 9:10 ` Nikolay 2007-09-18 9:57 ` Motsyo Gennadi aka Drool 1 sibling, 1 reply; 25+ messages in thread From: Nikolay @ 2007-09-18 9:10 UTC (permalink / raw) To: ALT Linux Sisyphus discussions В сообщении от 12 сентября 2007 Евгений написал(a): > >> Если можно - опишите пожалуйста процесс. > >> - рядом похожий 1010 посети работает на ура. :( > > > > Кстати, если подключить к Linux HP 1010 напрямую из-за кривого firmware > > на борту принтера через 3-5 заданий он прекращает печатать. > > Не подтверждаю. > Прекрасно работает. В работе HP 1010,1015,1018,1022. Нет - работает только до выключения принтера. Далее если принтер выключить и потом включить ( речь о 1018) то печать идёт в никуда а принтеру какимто макаром нада подгружать паршивку. Если ктотот может подскажите - как делать автоматом ... Список установленых пакетов могу предоставить. Система - текущий сизиф. > _______________________________________________ > Sisyphus mailing list > Sisyphus@lists.altlinux.org > https://lists.altlinux.org/mailman/listinfo/sisyphus -- С уважением, Николай ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-18 9:10 ` Nikolay @ 2007-09-18 9:57 ` Motsyo Gennadi aka Drool 2007-09-18 10:11 ` Nikolay 0 siblings, 1 reply; 25+ messages in thread From: Motsyo Gennadi aka Drool @ 2007-09-18 9:57 UTC (permalink / raw) To: ALT Linux Sisyphus discussions Nikolay пишет: > В сообщении от 12 сентября 2007 Евгений написал(a): > >>>> Если можно - опишите пожалуйста процесс. >>>> - рядом похожий 1010 посети работает на ура. :( >>> Кстати, если подключить к Linux HP 1010 напрямую из-за кривого firmware >>> на борту принтера через 3-5 заданий он прекращает печатать. >> Не подтверждаю. >> Прекрасно работает. В работе HP 1010,1015,1018,1022. > Нет - работает только до выключения принтера. > Далее если принтер выключить и потом включить ( речь о 1018) то печать идёт в > никуда а принтеру какимто макаром нада подгружать паршивку. > Если ктотот может подскажите - как делать автоматом ... > Список установленых пакетов могу предоставить. > Система - текущий сизиф. Тут что-то не так. В тех самых драйверах, которые я никак не могу запомнить :-) есть (была - точно) автодергалка, что-то типа своего собственного udev-а, которая при включении принтера подгружала прошивку из четко фиксированной папочки. Знаю точно, так как на АЛМ-2,4 я эту драйверуху как-то портировал и работал вроде именно 1018. ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-18 9:57 ` Motsyo Gennadi aka Drool @ 2007-09-18 10:11 ` Nikolay 2007-09-18 10:47 ` Igor Vlasenko 0 siblings, 1 reply; 25+ messages in thread From: Nikolay @ 2007-09-18 10:11 UTC (permalink / raw) To: ALT Linux Sisyphus discussions В сообщении от 18 сентября 2007 Motsyo Gennadi aka Drool написал(a): > Тут что-то не так. В тех самых драйверах, которые я никак не могу > запомнить :-) есть (была - точно) автодергалка, что-то типа своего > собственного udev-а, которая при включении принтера подгружала прошивку > из четко фиксированной папочки. Знаю точно, так как на АЛМ-2,4 я эту > драйверуху как-то портировал и работал вроде именно 1018. Всё так - и она есть /etc/udev/rules.d/11-hplj10xx.rules Если я правильно понимаю. НО - там /etc/hotplug/usb/hplj1000 в итоге а в нём мило DEV=/dev/usb/lp0 а cups у меня настроен на DeviceURI hp:/usb/HP_LaserJet_1018?serial=KP1NXX3 Если я правильно понимаю при появлении устройства дёргается именно /etc/hotplug/usb/hplj1000 - если так - то я постараюсь заставить его разбирать printers.conf для своего локального случая - да и всё. -- С уважением, Николай ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-18 10:11 ` Nikolay @ 2007-09-18 10:47 ` Igor Vlasenko 2007-09-18 11:16 ` Nikolay 2007-09-18 11:17 ` [sisyphus] Cups и HP LazerJet 1005 Шишков Евгений 0 siblings, 2 replies; 25+ messages in thread From: Igor Vlasenko @ 2007-09-18 10:47 UTC (permalink / raw) To: ALT Linux Sisyphus discussions On Tue, Sep 18, 2007 at 01:11:18PM +0300, Nikolay wrote: > В сообщении от 18 сентября 2007 Motsyo Gennadi aka Drool написал(a): > > Тут что-то не так. В тех самых драйверах, которые я никак не могу > > запомнить :-) есть (была - точно) автодергалка, что-то типа своего > > собственного udev-а, которая при включении принтера подгружала прошивку > > из четко фиксированной папочки. Знаю точно, так как на АЛМ-2,4 я эту > > драйверуху как-то портировал и работал вроде именно 1018. > Всё так - и она есть > /etc/udev/rules.d/11-hplj10xx.rules > Если я правильно понимаю. > НО - там > /etc/hotplug/usb/hplj1000 > в итоге а в нём мило DEV=/dev/usb/lp0 > а cups у меня настроен на > DeviceURI hp:/usb/HP_LaserJet_1018?serial=KP1NXX3 Судя по DeviceURI, вы (пытаетесь) печатать через hplip? > Если я правильно понимаю при появлении устройства дёргается именно > /etc/hotplug/usb/hplj1000 > - если так - то я постараюсь заставить его разбирать printers.conf для своего > локального случая - да и всё. -- Dr. Igor Vlasenko -------------------- Topology Department Institute of Math Kiev, Ukraine ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-18 10:47 ` Igor Vlasenko @ 2007-09-18 11:16 ` Nikolay 2007-09-18 11:25 ` Igor Vlasenko 2007-09-18 11:17 ` [sisyphus] Cups и HP LazerJet 1005 Шишков Евгений 1 sibling, 1 reply; 25+ messages in thread From: Nikolay @ 2007-09-18 11:16 UTC (permalink / raw) To: ALT Linux Sisyphus discussions В сообщении от 18 сентября 2007 Igor Vlasenko написал(a): > > DeviceURI hp:/usb/HP_LaserJet_1018?serial=KP1NXX3 > > Судя по DeviceURI, вы (пытаетесь) печатать через hplip? Да установлено hplip-foomatic-2.7.7-alt1 hplip-2.7.7-alt1 hplip-common-2.7.7-alt1 hplip-hpijs-2.7.7-alt1 hplip-gui-2.7.7-alt1 hplip-PPDs-2.7.7-alt1 hplip-foomatic-2.7.7-alt1 foomatic-filters-3.0.2-alt5 foomatic-db-engine-3.0.2-alt3 Собственно непонятно как надо ? -- С уважением, Николай ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1018 2007-09-18 11:16 ` Nikolay @ 2007-09-18 11:25 ` Igor Vlasenko 0 siblings, 0 replies; 25+ messages in thread From: Igor Vlasenko @ 2007-09-18 11:25 UTC (permalink / raw) To: ALT Linux Sisyphus discussions On Tue, Sep 18, 2007 at 02:16:08PM +0300, Nikolay wrote: > В сообщении от 18 сентября 2007 Igor Vlasenko написал(a): > > > DeviceURI hp:/usb/HP_LaserJet_1018?serial=KP1NXX3 > > > > Судя по DeviceURI, вы (пытаетесь) печатать через hplip? > Да установлено > hplip-foomatic-2.7.7-alt1 > hplip-2.7.7-alt1 > hplip-common-2.7.7-alt1 > hplip-hpijs-2.7.7-alt1 > hplip-gui-2.7.7-alt1 > hplip-PPDs-2.7.7-alt1 > hplip-foomatic-2.7.7-alt1 > foomatic-filters-3.0.2-alt5 > foomatic-db-engine-3.0.2-alt3 > > Собственно непонятно как надо ? Рекомендуется через foo2zjs. -- Dr. Igor Vlasenko -------------------- Topology Department Institute of Math Kiev, Ukraine ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1005 2007-09-18 10:47 ` Igor Vlasenko 2007-09-18 11:16 ` Nikolay @ 2007-09-18 11:17 ` Шишков Евгений 2007-09-18 11:21 ` Motsyo Gennadi aka Drool 2007-09-18 11:49 ` Nikolay 1 sibling, 2 replies; 25+ messages in thread From: Шишков Евгений @ 2007-09-18 11:17 UTC (permalink / raw) To: ALT Linux Sisyphus discussions Igor Vlasenko пишет: > On Tue, Sep 18, 2007 at 01:11:18PM +0300, Nikolay wrote: >> В сообщении от 18 сентября 2007 Motsyo Gennadi aka Drool написал(a): >>> Тут что-то не так. В тех самых драйверах, которые я никак не могу >>> запомнить :-) есть (была - точно) автодергалка, что-то типа своего >>> собственного udev-а, которая при включении принтера подгружала прошивку >>> из четко фиксированной папочки. Знаю точно, так как на АЛМ-2,4 я эту >>> драйверуху как-то портировал и работал вроде именно 1018. >> Всё так - и она есть >> /etc/udev/rules.d/11-hplj10xx.rules >> Если я правильно понимаю. >> НО - там >> /etc/hotplug/usb/hplj1000 >> в итоге а в нём мило DEV=/dev/usb/lp0 >> а cups у меня настроен на >> DeviceURI hp:/usb/HP_LaserJet_1018?serial=KP1NXX3 > > Судя по DeviceURI, вы (пытаетесь) печатать через hplip? > >> Если я правильно понимаю при появлении устройства дёргается именно >> /etc/hotplug/usb/hplj1000 >> - если так - то я постараюсь заставить его разбирать printers.conf для своего >> локального случая - да и всё. Немножко изменю тему и расскажу как я вчера заводил HP1005. Ставим foo2zjs. Устанавливаем драйвер принтера (естественно выбираем foo2zjs) Далее нам надо загрузить в него микропрогу. Но её надо скачать. Делаем getweb 1005 (нужно wget ещё поставить) Запустится утилька и скачает img файл. Из этого файла нам надо сделать dl файл. Делаем. #arm2hpdl sihp1005.img > ship1005.dl И получаем dl файл. Он должен лежать в /usr/share/foo2zjs/firmware Далее делаем #cat /usr/share/foo2zjs/firmware/sihp1005.dl > /dev/usb/lp0 Насколько понял последняя команда даётся один раз. Т.к. после выключения питания и перезагрузки компьютера у меня всё продолжает работать. Утильки getweb и arm2hpdl ставятся с пакетом foo2zjs. Всё!!!!. ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1005 2007-09-18 11:17 ` [sisyphus] Cups и HP LazerJet 1005 Шишков Евгений @ 2007-09-18 11:21 ` Motsyo Gennadi aka Drool 2007-09-18 11:24 ` Motsyo Gennadi aka Drool 2007-09-18 11:29 ` Шишков Евгений 2007-09-18 11:49 ` Nikolay 1 sibling, 2 replies; 25+ messages in thread From: Motsyo Gennadi aka Drool @ 2007-09-18 11:21 UTC (permalink / raw) To: ALT Linux Sisyphus discussions Шишков Евгений пишет: > Далее делаем > #cat /usr/share/foo2zjs/firmware/sihp1005.dl > /dev/usb/lp0 > > Насколько понял последняя команда даётся один раз. Т.к. после выключения питания и > перезагрузки компьютера у меня всё продолжает работать. Да, так как эта самая команда присутствует во внутренних скриптах драйверов. Вручную Вы ее запускали потому-что не захотели перегружать систему ;-) После перезагрузки, а возможно и при простом передергивани USB-кабеля модема она должна была сработать сама. Когда я портировал на АЛМ-2.4 foo2zjs - я в постинсталл-скриптах самого rpm-пакета по-моему прописывал сие действие. ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1005 2007-09-18 11:21 ` Motsyo Gennadi aka Drool @ 2007-09-18 11:24 ` Motsyo Gennadi aka Drool 2007-09-18 11:29 ` Шишков Евгений 1 sibling, 0 replies; 25+ messages in thread From: Motsyo Gennadi aka Drool @ 2007-09-18 11:24 UTC (permalink / raw) To: ALT Linux Sisyphus discussions Motsyo Gennadi aka Drool пишет: > USB-кабеля модема она должна была сработать сама. Фу, блин, модема :-) Принтера! P.S. Тяжело быть чиновником :-( ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1005 2007-09-18 11:21 ` Motsyo Gennadi aka Drool 2007-09-18 11:24 ` Motsyo Gennadi aka Drool @ 2007-09-18 11:29 ` Шишков Евгений 2007-09-18 11:33 ` Motsyo Gennadi aka Drool 1 sibling, 1 reply; 25+ messages in thread From: Шишков Евгений @ 2007-09-18 11:29 UTC (permalink / raw) To: ALT Linux Sisyphus discussions Motsyo Gennadi aka Drool пишет: > Шишков Евгений пишет: >> Далее делаем >> #cat /usr/share/foo2zjs/firmware/sihp1005.dl > /dev/usb/lp0 >> >> Насколько понял последняя команда даётся один раз. Т.к. после выключения питания и >> перезагрузки компьютера у меня всё продолжает работать. > > Да, так как эта самая команда присутствует во внутренних скриптах > драйверов. Вручную Вы ее запускали потому-что не захотели перегружать > систему ;-) После перезагрузки, а возможно и при простом передергивани > USB-кабеля модема она должна была сработать сама. > Когда я портировал на АЛМ-2.4 foo2zjs - я в постинсталл-скриптах самого > rpm-пакета по-моему прописывал сие действие. Ну а как прописывать сиё действие, если не знаешь, какой принтер подключится? Да и прошивок то нет. Их качать надо. А передёргивать/перезагружать не стал потому, что просто доку почитал. Там всё написано на америкосовом языке (тудыт их). foo2zjs брал из сизифа. Правда половину foomatic'а снести пришлось из-за конфликта. ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1005 2007-09-18 11:29 ` Шишков Евгений @ 2007-09-18 11:33 ` Motsyo Gennadi aka Drool 0 siblings, 0 replies; 25+ messages in thread From: Motsyo Gennadi aka Drool @ 2007-09-18 11:33 UTC (permalink / raw) To: ALT Linux Sisyphus discussions Шишков Евгений пишет: > Ну а как прописывать сиё действие, если не знаешь, какой принтер подключится? Сам драйвер знает какому принтеру какую прошивку. > Да и прошивок то нет. Их качать надо. Я нужный файлик нашел на диске с виндявыми дровами (img) и сконвертил в нужный формат как было указано в соседнем письме ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1005 2007-09-18 11:17 ` [sisyphus] Cups и HP LazerJet 1005 Шишков Евгений 2007-09-18 11:21 ` Motsyo Gennadi aka Drool @ 2007-09-18 11:49 ` Nikolay 2007-09-18 12:06 ` Шишков Евгений 2007-09-26 6:10 ` [sisyphus] а теперь на wiki pls :) " Michael Shigorin 1 sibling, 2 replies; 25+ messages in thread From: Nikolay @ 2007-09-18 11:49 UTC (permalink / raw) To: ALT Linux Sisyphus discussions В сообщении от 18 сентября 2007 Шишков Евгений написал(a): > Ставим foo2zjs. > Устанавливаем драйвер принтера (естественно выбираем foo2zjs) > Далее нам надо загрузить в него микропрогу. > Но её надо скачать. Делаем getweb 1005 (нужно wget ещё поставить) > Запустится утилька и скачает img файл. > Из этого файла нам надо сделать dl файл. > Делаем. > > #arm2hpdl sihp1005.img > ship1005.dl ВОТ ! - спасибо данную операцию проглядел. а так foo2zjs установлен foo2zjs-20060523-alt0.4 и > Далее делаем > #cat /usr/share/foo2zjs/firmware/sihp1005.dl > /dev/usb/lp0 сделал cat /usr/share/foo2zjs/firmware/sihp1018.dl > /dev/hplj1018%e Счастье случилось. Принтер - выключил включил печать работает. Спасибо за консультацию. -- С уважением, Николай ^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [sisyphus] Cups и HP LazerJet 1005 2007-09-18 11:49 ` Nikolay @ 2007-09-18 12:06 ` Шишков Евгений 2007-09-26 6:10 ` [sisyphus] а теперь на wiki pls :) " Michael Shigorin 1 sibling, 0 replies; 25+ messages in thread From: Шишков Евгений @ 2007-09-18 12:06 UTC (permalink / raw) To: ALT Linux Sisyphus discussions Nikolay пишет: > В сообщении от 18 сентября 2007 Шишков Евгений написал(a): >> Ставим foo2zjs. >> Устанавливаем драйвер принтера (естественно выбираем foo2zjs) >> Далее нам надо загрузить в него микропрогу. >> Но её надо скачать. Делаем getweb 1005 (нужно wget ещё поставить) >> Запустится утилька и скачает img файл. >> Из этого файла нам надо сделать dl файл. >> Делаем. >> >> #arm2hpdl sihp1005.img > ship1005.dl > ВОТ ! - спасибо данную операцию проглядел. > а так foo2zjs установлен > foo2zjs-20060523-alt0.4 > и >> Далее делаем >> #cat /usr/share/foo2zjs/firmware/sihp1005.dl > /dev/usb/lp0 > сделал cat /usr/share/foo2zjs/firmware/sihp1018.dl > /dev/hplj1018%e > Счастье случилось. > Принтер - выключил включил печать работает. > Спасибо за консультацию. > Пожалуйста. ^ permalink raw reply [flat|nested] 25+ messages in thread
* [sisyphus] а теперь на wiki pls :) Re: Cups и HP LazerJet 1005 2007-09-18 11:49 ` Nikolay 2007-09-18 12:06 ` Шишков Евгений @ 2007-09-26 6:10 ` Michael Shigorin 1 sibling, 0 replies; 25+ messages in thread From: Michael Shigorin @ 2007-09-26 6:10 UTC (permalink / raw) To: ALT Linux Sisyphus discussions On Tue, Sep 18, 2007 at 03:17:41PM +0400, Шишков Евгений wrote: > Немножко изменю тему и расскажу как я вчера заводил HP1005. Евгений (или Николай?), а не хотите создать страничку http://www.freesource.info/wiki/HCL/Periferija/Printery/HP? Туда бы и про те, которые foo2zjs, и hplip, и честные PCL/PS можно было написать, чтоб по архивам рассылки не рыскать. On Tue, Sep 18, 2007 at 03:29:18PM +0400, Шишков Евгений wrote: > Ну а как прописывать сиё действие, если не знаешь, какой > принтер подключится? Да и прошивок то нет. Их качать надо. Кстати, никто не хочет черкнуть в HP (да, я понимаю, что мне-то с их публичных никто и никогда ещё живой не отвечал...) -- поинтересоваться, можно ли "для линукса" распространять их firmware? > foo2zjs брал из сизифа. Правда половину foomatic'а снести > пришлось из-за конфликта. Уже (опять/пока) fixed. On Tue, Sep 18, 2007 at 02:49:22PM +0300, Nikolay wrote: > > Но её надо скачать. Делаем getweb 1005 (нужно wget ещё > > поставить) Запустится утилька и скачает img файл. > > Из этого файла нам надо сделать dl файл. Делаем. > > #arm2hpdl sihp1005.img > ship1005.dl > ВОТ ! - спасибо данную операцию проглядел. И это туда же не забыть. *Жирным*. :) (я обдумывал сделать какую-то автоматизацию getweb или посмотреть условия распространения прошивок, но времени завершить это всё не хватило -- оставил как есть) -- ---- WBR, Michael Shigorin <mike@altlinux.ru> ------ Linux.Kiev http://www.linux.kiev.ua/ ^ permalink raw reply [flat|nested] 25+ messages in thread
end of thread, other threads:[~2007-09-26 6:10 UTC | newest] Thread overview: 25+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2007-09-12 13:15 [sisyphus] Cups и HP LazerJet 1018 Nikolay 2007-09-12 13:24 ` Motsyo Gennadi aka Drool 2007-09-12 13:27 ` Nikolay 2007-09-12 13:40 ` Андрей Черепанов 2007-09-12 13:58 ` Nikolay 2007-09-12 14:23 ` Евгений 2007-09-12 14:26 ` Nikolay 2007-09-13 4:24 ` Шишков Евгений 2007-09-16 19:46 ` Michael Shigorin 2007-09-12 14:19 ` Евгений 2007-09-16 19:47 ` Michael Shigorin 2007-09-18 9:10 ` Nikolay 2007-09-18 9:57 ` Motsyo Gennadi aka Drool 2007-09-18 10:11 ` Nikolay 2007-09-18 10:47 ` Igor Vlasenko 2007-09-18 11:16 ` Nikolay 2007-09-18 11:25 ` Igor Vlasenko 2007-09-18 11:17 ` [sisyphus] Cups и HP LazerJet 1005 Шишков Евгений 2007-09-18 11:21 ` Motsyo Gennadi aka Drool 2007-09-18 11:24 ` Motsyo Gennadi aka Drool 2007-09-18 11:29 ` Шишков Евгений 2007-09-18 11:33 ` Motsyo Gennadi aka Drool 2007-09-18 11:49 ` Nikolay 2007-09-18 12:06 ` Шишков Евгений 2007-09-26 6:10 ` [sisyphus] а теперь на wiki pls :) " Michael Shigorin
ALT Linux Sisyphus discussions This inbox may be cloned and mirrored by anyone: git clone --mirror http://lore.altlinux.org/sisyphus/0 sisyphus/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 sisyphus sisyphus/ http://lore.altlinux.org/sisyphus \ sisyphus@altlinux.ru sisyphus@altlinux.org sisyphus@lists.altlinux.org sisyphus@lists.altlinux.ru sisyphus@lists.altlinux.com sisyphus@linuxteam.iplabs.ru sisyphus@list.linux-os.ru public-inbox-index sisyphus Example config snippet for mirrors. Newsgroup available over NNTP: nntp://lore.altlinux.org/org.altlinux.lists.sisyphus AGPL code for this site: git clone https://public-inbox.org/public-inbox.git