From: Aleksey Avdeev <solo@solin.spb.ru>
To: hardware@lists.altlinux.org
Subject: Re: [Hardware] Q: SAS RAID Vitesse VSC7250: Кто нибудь сталкивался?
Date: Thu, 01 Nov 2007 16:22:12 +0300
Message-ID: <4729D304.4060906@solin.spb.ru> (raw)
In-Reply-To: <47284CA8.10906@solin.spb.ru>
[-- Attachment #1: Type: text/plain, Size: 554 bytes --]
Aleksey Avdeev пишет:
> Sergey Vlasov пишет:
>> On Tue, Oct 30, 2007 at 02:37:50PM +0300, Aleksey Avdeev wrote:
>>> Sergey Vlasov пишет:
>>>> On Tue, Oct 30, 2007 at 02:16:05PM +0300, Aleksey Avdeev wrote:
>>>>> lspci.txt приложен (с загруженным i2o-block).
>>>> Не вижу...
>>> Сорри...
>> Там ничего нет, кроме чипсета и двух устройств моста PCI-X. Либо этот
>> RAID-контроллер выключен в настройках BIOS, либо вообще не работает;
>
> Похоже, отключён перемычкой...
Включил. Результаты pciscan и lspci приложены.
--
С уважением. Алексей.
[-- Attachment #2: lspci.2.txt --]
[-- Type: text/plain, Size: 30178 bytes --]
00:00.0 RAM memory [0500]: nVidia Corporation MCP55 Memory Controller [10de:0369] (rev a2)
Subsystem: nVidia Corporation Unknown device [10de:cb84]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 1.0GHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [dc] HyperTransport: MSI Mapping
00:01.0 ISA bridge [0601]: nVidia Corporation MCP55 LPC Bridge [10de:0364] (rev a3)
Subsystem: nVidia Corporation Unknown device [10de:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: I/O ports at 1c00 [size=128]
00:01.1 SMBus [0c05]: nVidia Corporation MCP55 SMBus [10de:0368] (rev a3)
Subsystem: nVidia Corporation Unknown device [10de:cb84]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 255
Region 4: I/O ports at 3040 [size=64]
Region 5: I/O ports at 3000 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.0 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller [10de:036c] (rev a1) (prog-if 10 [OHCI])
Subsystem: nVidia Corporation Unknown device [10de:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at b8040000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller [10de:036d] (rev a2) (prog-if 20 [EHCI])
Subsystem: nVidia Corporation Unknown device [10de:cb84]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at b8041000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 IDE interface [0101]: nVidia Corporation MCP55 IDE [10de:036e] (rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: nVidia Corporation Unknown device [10de:cb84]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at 3080 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:05.0 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller [10de:037f] (rev a3) (prog-if 85 [Master SecO PriO])
Subsystem: nVidia Corporation Unknown device [10de:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 30d0 [size=8]
Region 1: I/O ports at 30c4 [size=4]
Region 2: I/O ports at 30c8 [size=8]
Region 3: I/O ports at 30c0 [size=4]
Region 4: I/O ports at 3090 [size=16]
Region 5: Memory at b8042000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping
00:05.1 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller [10de:037f] (rev a3) (prog-if 85 [Master SecO PriO])
Subsystem: nVidia Corporation Unknown device [10de:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at 30e8 [size=8]
Region 1: I/O ports at 30dc [size=4]
Region 2: I/O ports at 30e0 [size=8]
Region 3: I/O ports at 30d8 [size=4]
Region 4: I/O ports at 30a0 [size=16]
Region 5: Memory at b8043000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping
00:05.2 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller [10de:037f] (rev a3) (prog-if 85 [Master SecO PriO])
Subsystem: nVidia Corporation Unknown device [10de:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 19
Region 0: I/O ports at 3400 [size=8]
Region 1: I/O ports at 30f4 [size=4]
Region 2: I/O ports at 30f8 [size=8]
Region 3: I/O ports at 30f0 [size=4]
Region 4: I/O ports at 30b0 [size=16]
Region 5: Memory at b8044000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping
00:06.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI bridge [10de:0370] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00004000-00004fff
Memory behind bridge: b8100000-b81fffff
Prefetchable memory behind bridge: c0000000-c7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [b8] Subsystem: Gammagraphx, Inc. Unknown device [0000:0000]
Capabilities: [8c] HyperTransport: MSI Mapping
00:08.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a3)
Subsystem: nVidia Corporation Unknown device [10de:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at b8045000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 3408 [size=8]
Region 2: Memory at b8041800 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at b8041400 (32-bit, non-prefetchable) [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [70] MSI-X: Enable- Mask- TabSize=8
Vector table: BAR=2 offset=00000000
PBA: BAR=3 offset=00000000
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/3 Enable-
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping
00:09.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a3)
Subsystem: nVidia Corporation Unknown device [10de:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at b8047000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 3410 [size=8]
Region 2: Memory at b8046000 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at b8041c00 (32-bit, non-prefetchable) [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [70] MSI-X: Enable- Mask- TabSize=8
Vector table: BAR=2 offset=00000000
PBA: BAR=3 offset=00000000
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/3 Enable-
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping
00:0a.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0376] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Subsystem: nVidia Corporation Unknown device [10de:0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 5
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:0b.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0374] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Subsystem: nVidia Corporation Unknown device [10de:0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x0, ASPM L0s L1, Port 4
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:0c.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0374] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Subsystem: nVidia Corporation Unknown device [10de:0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x0, ASPM L0s L1, Port 3
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:0d.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0378] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=07, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: b8200000-b83fffff
Prefetchable memory behind bridge: 00000000b4000000-00000000b40fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Subsystem: nVidia Corporation Unknown device [10de:0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 2
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:0e.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0375] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Subsystem: nVidia Corporation Unknown device [10de:0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 1
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:0f.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0377] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
I/O behind bridge: 00006000-00006fff
Memory behind bridge: b8400000-b84fffff
Prefetchable memory behind bridge: 00000000c8000000-00000000c80fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Subsystem: nVidia Corporation Unknown device [10de:0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x2
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]
01:06.0 VGA compatible controller [0300]: ATI Technologies Inc ES1000 [1002:515e] (rev 02) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc ES1000 [1002:515e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 4000 [size=256]
Region 2: Memory at b8100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at b8120000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:00.0 PCI bridge [0604]: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge [1033:0125] (rev 06) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=05, secondary=06, subordinate=06, sec-latency=70
I/O behind bridge: 00005000-00005fff
Memory behind bridge: b8300000-b83fffff
Prefetchable memory behind bridge: 00000000b4000000-00000000b40fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <4us, L1 <16us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Capabilities: [54] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
Status: Dev=05:00.0 64bit- 133MHz- SCD- USC- SCO- SRD-
Upstream: Capacity=32 CommitmentLimit=32
Downstream: Capacity=16 CommitmentLimit=16
Capabilities: [64] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=55mA PME(D0+,D1+,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
05:00.1 PCI bridge [0604]: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge [1033:0125] (rev 06) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Region 0: Memory at b8200000 (64-bit, non-prefetchable) [size=128]
Bus: primary=05, secondary=07, subordinate=07, sec-latency=4
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <4us, L1 <16us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Capabilities: [54] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
Status: Dev=05:00.1 64bit- 133MHz- SCD- USC- SCO- SRD-
Upstream: Capacity=32 CommitmentLimit=32
Downstream: Capacity=16 CommitmentLimit=16
Capabilities: [64] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=55mA PME(D0+,D1+,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [6c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [7c] #0c [0009]
06:02.0 Ethernet controller [0200]: Intel Corporation 82557/8/9 Ethernet Pro 100 [8086:1229] (rev 0d)
Subsystem: Intel Corporation EtherExpress PRO/100 S Desktop Adapter [8086:0040]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at b8320000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 5000 [size=64]
Region 2: Memory at b8300000 (32-bit, non-prefetchable) [size=128K]
[virtual] Expansion ROM at b4000000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
09:00.0 RAID bus controller [0104]: Promise Technology, Inc. Unknown device [105a:7250] (rev 03)
Subsystem: Promise Technology, Inc. Unknown device [105a:1001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at b8400000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at c8000000 (64-bit, prefetchable) [size=64K]
Region 4: I/O ports at 6000 [size=256]
Expansion ROM at c8010000 [disabled] [size=64K]
Capabilities: [40] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <128ns, L1 <2us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled RCB 128 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x2
Capabilities: [58] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [e0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable-
Address: 0000000000000000 Data: 0000
[-- Attachment #3: pciscan.txt --]
[-- Type: text/plain, Size: 2534 bytes --]
Recommended driver Description
------------------ -----------
unknown nVidia Corporation MCP55 Memory Controller [RAM memory]
unknown nVidia Corporation MCP55 LPC Bridge [ISA bridge]
i2c-nforce2 nVidia Corporation MCP55 SMBus [SMBus]
ohci-hcd nVidia Corporation MCP55 USB Controller [OHCI USB Controller]
ehci-hcd nVidia Corporation MCP55 USB Controller [EHCI USB Controller]
amd74xx nVidia Corporation MCP55 IDE [IDE interface storage controller]
sata_nv nVidia Corporation MCP55 SATA Controller [IDE interface storage controller]
sata_nv nVidia Corporation MCP55 SATA Controller [IDE interface storage controller]
sata_nv nVidia Corporation MCP55 SATA Controller [IDE interface storage controller]
shpchp nVidia Corporation MCP55 PCI bridge [PCI bridge Normal decode]
forcedeth nVidia Corporation MCP55 Ethernet [Bridge]
forcedeth nVidia Corporation MCP55 Ethernet [Bridge]
shpchp nVidia Corporation MCP55 PCI Express bridge [PCI bridge Normal decode]
shpchp nVidia Corporation MCP55 PCI Express bridge [PCI bridge Normal decode]
shpchp nVidia Corporation MCP55 PCI Express bridge [PCI bridge Normal decode]
shpchp nVidia Corporation MCP55 PCI Express bridge [PCI bridge Normal decode]
shpchp nVidia Corporation MCP55 PCI Express bridge [PCI bridge Normal decode]
shpchp nVidia Corporation MCP55 PCI Express bridge [PCI bridge Normal decode]
unknown Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [Host bridge]
unknown Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [Host bridge]
unknown Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [Host bridge]
k8temp Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [Host bridge]
radeonfb ATI Technologies Inc ES1000 [VGA compatible controller]
shpchp NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge [PCI bridge Normal decode]
shpchp NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge [PCI bridge Normal decode]
eepro100 Intel Corporation 82557/8/9 Ethernet Pro 100 [Ethernet controller]
unknown Promise Technology, Inc. Unknown device 7250 [RAID bus controller]
next prev parent reply other threads:[~2007-11-01 13:22 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-10-29 15:45 [Hardware] Q: SAS RAID Vitesse VSC7250: Ктонибудь сталкивался? Aleksey Avdeev
2007-10-29 16:09 ` Michael Shigorin
2007-10-29 18:54 ` Sergey Vlasov
2007-10-31 19:14 ` [Hardware] о разных LSI SAS1068 и SAS1064 Michael Shigorin
2007-10-29 18:44 ` [Hardware] Q: SAS RAID Vitesse VSC7250: Ктонибудь сталкивался? Sergey Vlasov
2007-10-30 11:16 ` [Hardware] Q: SAS RAID Vitesse VSC7250: Кто нибудь сталкивался? Aleksey Avdeev
2007-10-30 11:33 ` Sergey Vlasov
2007-10-30 11:37 ` Aleksey Avdeev
2007-10-30 12:58 ` Sergey Vlasov
2007-10-31 9:36 ` Aleksey Avdeev
2007-11-01 13:22 ` Aleksey Avdeev [this message]
2007-11-01 15:38 ` Sergey Vlasov
2007-11-01 20:29 ` Aleksey Avdeev
2007-11-02 11:05 ` Sergey Vlasov
2007-11-02 11:42 ` Michael Shigorin
2007-11-02 12:29 ` Aleksey Avdeev
2007-11-02 12:39 ` Michael Shigorin
2007-10-30 11:50 ` Aleksey Avdeev
2007-10-31 18:40 ` [Hardware] Q: SAS RAID Vitesse VSC7250: Ктонибудь сталкивался? Michael Shigorin
2007-10-30 9:29 ` Mike Lykov
2007-10-30 9:44 ` Mike Lykov
2007-10-31 9:46 ` Aleksey Avdeev
2007-10-31 18:45 ` Michael Shigorin
2007-10-31 19:38 ` Aleksey Avdeev
2007-10-31 19:46 ` Maks Re
2007-10-31 19:59 ` Aleksey Avdeev
2007-10-31 19:48 ` Michael Shigorin
2007-10-31 20:12 ` Aleksey Avdeev
2007-10-31 11:09 ` Mike Lykov
2007-10-31 11:27 ` Aleksey Avdeev
2007-10-30 10:04 ` Mike Lykov
2007-10-30 10:43 ` Sergey Vlasov
2007-10-31 7:31 ` Mike Lykov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4729D304.4060906@solin.spb.ru \
--to=solo@solin.spb.ru \
--cc=hardware@lists.altlinux.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
ALT Linux hardware support
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/hardware/0 hardware/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 hardware hardware/ http://lore.altlinux.org/hardware \
hardware@altlinux.ru hardware@lists.altlinux.org hardware@lists.altlinux.ru hardware@lists.altlinux.com hardware@altlinux.org
public-inbox-index hardware
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.hardware
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git