* Re: [Hardware] UDMA5
2006-03-01 9:33 ` Sergey Vlasov
@ 2006-03-01 12:18 ` Eugene Prokopiev
2006-03-01 13:30 ` Sergey Vlasov
0 siblings, 1 reply; 6+ messages in thread
From: Eugene Prokopiev @ 2006-03-01 12:18 UTC (permalink / raw)
To: hardware
Sergey Vlasov пишет:
> On Wed, Mar 01, 2006 at 11:59:09AM +0300, Eugene Prokopiev wrote:
>
>>Есть 2 винта, про которых в биосе написано:
>>
>>Drive Installed: ST40014A
>>PIO Mode: Mode 4
>>Ultra DMA: Mode 5
>>Cable Detected: 80 Conductor
>>
>>Однако:
>>
>># hdparm -i /dev/hda
>
>
> А hdparm -I что пишет?
>
> [skip]
>
>># hdparm -Xudma5 /dev/hdc
>>
>>/dev/hdc:
>> setting xfermode to 69 (UltraDMA mode5)
>> HDIO_DRIVE_CMD(setxfermode) failed: Input/output error
>
>
> Какой контроллер? lspci, dmesg?
# hdparm -I /dev/hda
/dev/hda:
ATA device, with non-removable media
Model Number: ST340014A
Serial Number: 3JX1LYA5
Firmware Revision: 3.06
Standards:
Used: ATA/ATAPI-6 T13 1410D revision 2
Supported: 6 5 4 3
Configuration:
Logical max current
cylinders 16383 65535
heads 16 1
sectors/track 63 63
--
CHS current addressable sectors: 4128705
LBA user addressable sectors: 78165360
LBA48 user addressable sectors: 78165360
device size with M = 1024*1024: 38166 MBytes
device size with M = 1000*1000: 40020 MBytes (40 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Standard
R/W multiple sector transfer: Max = 16 Current = 16
Recommended acoustic management value: 128, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct
# hdparm -I /dev/hdc
/dev/hdc:
ATA device, with non-removable media
Model Number: ST340014A
Serial Number: 5JXKSS6C
Firmware Revision: 8.01
Standards:
Used: ATA/ATAPI-6 T13 1410D revision 2
Supported: 6 5 4 3
Configuration:
Logical max current
cylinders 16383 65535
heads 16 1
sectors/track 63 63
--
CHS current addressable sectors: 4128705
LBA user addressable sectors: 78165360
LBA48 user addressable sectors: 78165360
device size with M = 1024*1024: 38166 MBytes
device size with M = 1000*1000: 40020 MBytes (40 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Standard, no device specific
minimum
R/W multiple sector transfer: Max = 16 Current = 16
Recommended acoustic management value: 128, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
* General Purpose Logging feature set
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- below Vih
Device num = 0 determined by the jumper
Checksum: correct
Но:
# hdparm -i /dev/hda
/dev/hda:
Model=ST340014A, FwRev=3.06, SerialNo=3JX1LYA5
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:
* signifies the current active mode
# hdparm -i /dev/hdc
/dev/hdc:
Model=ST340014A, FwRev=8.01, SerialNo=5JXKSS6C
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:
* signifies the current active mode
# lspci
00:00.0 Host bridge: Intel Corp. 82845G/GL[Brookdale-G]/GE/PE DRAM
Controller/Host-Hub Interface (rev 01)
00:02.0 VGA compatible controller: Intel Corp. 82845G/GL[Brookdale-G]/GE
Chipset Integrated Graphics Device (rev 01)
00:1d.0 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #1 (rev 01)
00:1d.1 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #2 (rev 01)
00:1d.2 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #3 (rev 01)
00:1d.7 USB Controller: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller
(rev 01)
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB/ER Hub interface to PCI
Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corp. 82801DB (ICH4) LPC Bridge (rev 01)
00:1f.1 IDE interface: Intel Corp. 82801DB (ICH4) Ultra ATA 100 Storage
Controller (rev 01)
00:1f.3 SMBus: Intel Corp. 82801DB/DBM (ICH4) SMBus Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corp. 82801DB (ICH4) AC'97
Audio Controller (rev 01)
01:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado]
(rev 78)
01:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
# dmesg
2.3 present.
62 structures occupying 2310 bytes.
DMI table at 0x000FC610.
BIOS Vendor: Intel Corp.
BIOS Version: LY84510A.86A.0029.P11.0212121810
BIOS Release: 12/12/2002
System Vendor:
Product Name:
Version:
Serial Number:
Board Vendor: Intel Corporation
Board Name: D845GLAD
Board Version: AAA86713-207
ACPI: RSDP (v000 ACPIAM ) @ 0x000f7210
ACPI: RSDT (v001 INTEL D845GLAD 0x12000212 MSFT 0x00000097) @ 0x1fe40000
ACPI: FADT (v002 INTEL D845GLAD 0x12000212 MSFT 0x00000097) @ 0x1fe40200
ACPI: MADT (v001 INTEL D845GLAD 0x12000212 MSFT 0x00000097) @ 0x1fe40300
ACPI: ASF! (v016 AMIASF I845GASF 0x00000001 MSFT 0x0100000d) @ 0x1fe444b0
ACPI: DSDT (v001 INTEL D845GLAD 0x0000010a MSFT 0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 Pentium 4(tm) XEON(tm) APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 1
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Using ACPI (MADT) for SMP configuration information
Kernel command line: auto BOOT_IMAGE=linux-smp ro root=3a00 ramdisk=8192
splash=off
Initializing CPU#0
Detected 2399.770 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 4784.12 BogoMIPS
Memory: 511496k/522496k available (1358k kernel code, 10612k reserved,
542k data, 152k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU0: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 07
per-CPU timeslice cutoff: 1462.99 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22,
1-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2399.7104 MHz.
..... host bus clock speed is 99.9878 MHz.
cpu: 0, clocks: 999878, slice: 499939
CPU0<T0:999872,T1:499920,D:13,S:499939,C:999878>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
ACPI: Subsystem revision 20040326
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
Looking for DSDT in initrd ... not found!
ACPI-1132: *** Error: Method execution failed [\GPRW] (Node
c160da20), AE_NOT_EXIST
ACPI-1132: *** Error: Method execution failed
[\_SB_.PCI0.P0P1._PRW] (Node c160dda0), AE_NOT_EXIST
ACPI-0153: *** Error: Method execution failed
[\_SB_.PCI0.P0P1._PRW] (Node c160dda0), AE_NOT_EXIST
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
PCI: Probing PCI hardware
00:00:1d[A] -> 1-16 -> IRQ 16 level low
00:00:1d[B] -> 1-19 -> IRQ 19 level low
00:00:1d[C] -> 1-18 -> IRQ 18 level low
00:00:1d[D] -> 1-23 -> IRQ 23 level low
00:00:1f[B] -> 1-17 -> IRQ 17 level low
00:01:08[A] -> 1-20 -> IRQ 20 level low
00:01:00[A] -> 1-21 -> IRQ 21 level low
00:01:00[B] -> 1-22 -> IRQ 22 level low
number of MP IRQ sources: 15.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 A9
11 001 01 1 1 0 1 0 1 1 C9
12 001 01 1 1 0 1 0 1 1 B9
13 001 01 1 1 0 1 0 1 1 B1
14 001 01 1 1 0 1 0 1 1 D1
15 001 01 1 1 0 1 0 1 1 D9
16 001 01 1 1 0 1 0 1 1 E1
17 001 01 1 1 0 1 0 1 1 C1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
kinoded started
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xf0000000, mapped to 0xe080a000, size 832k
vesafb: mode is 640x480x16, linelength=1280, pages=0
vesafb: protected mode interface info at a5f3:1f5f
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture... no good signature found.
Console: switching to colour frame buffer device 80x30
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: ST340014A, ATA DISK drive
blk: queue c036c7e0, I/O limit 4095Mb (mask 0xffffffff)
hdc: ST340014A, ATA DISK drive
blk: queue c036cc50, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(100)
hdc: attached ide-disk driver.
hdc: host protected area => 1
hdc: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(100)
Partition check:
hda: hda1 hda2 hda3
hdc: hdc1 hdc2 hdc3
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
[events: 0000002b]
[events: 0000002b]
[events: 0000002b]
[events: 0000002b]
md: autorun ...
md: considering hdc3 ...
md: adding hdc3 ...
md: adding hda3 ...
md: created md1
md: bind<hda3,1>
md: bind<hdc3,2>
md: running: <hdc3><hda3>
md: hdc3's event counter: 0000002b
md: hda3's event counter: 0000002b
md: md1: raid array is not clean -- starting background reconstruction
kmod: failed to exec /sbin/modprobe -s -k md-personality-3, errno = 2
md: personality 3 is not loaded!
md :do_md_run() returned -22
md: md1 stopped.
md: unbind<hdc3,1>
md: export_rdev(hdc3)
md: unbind<hda3,0>
md: export_rdev(hda3)
md: considering hdc1 ...
md: adding hdc1 ...
md: adding hda1 ...
md: created md0
md: bind<hda1,1>
md: bind<hdc1,2>
md: running: <hdc1><hda1>
md: hdc1's event counter: 0000002b
md: hda1's event counter: 0000002b
kmod: failed to exec /sbin/modprobe -s -k md-personality-3, errno = 2
md: personality 3 is not loaded!
md :do_md_run() returned -22
md: md0 stopped.
md: unbind<hdc1,1>
md: export_rdev(hdc1)
md: unbind<hda1,0>
md: export_rdev(hda1)
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1779k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
LVM version 1.0.8(17/11/2003) module loaded
Journalled Block Device driver loaded
md: raid1 personality registered as nr 3
md: Autodetecting RAID arrays.
[events: 0000002b]
[events: 0000002b]
[events: 0000002b]
[events: 0000002b]
md: autorun ...
md: considering hda1 ...
md: adding hda1 ...
md: adding hdc1 ...
md: created md0
md: bind<hdc1,1>
md: bind<hda1,2>
md: running: <hda1><hdc1>
md: hda1's event counter: 0000002b
md: hdc1's event counter: 0000002b
md0: max total readahead window set to 124k
md0: 1 data-disks, max readahead per data-disk: 124k
raid1: device hda1 operational as mirror 0
raid1: device hdc1 operational as mirror 1
raid1: raid set md0 active with 2 out of 2 mirrors
md: updating md0 RAID superblock on device
md: hda1 [events: 0000002c]<6>(write) hda1's sb offset: 48064
md: hdc1 [events: 0000002c]<6>(write) hdc1's sb offset: 48064
md: considering hda3 ...
md: adding hda3 ...
md: adding hdc3 ...
md: created md1
md: bind<hdc3,1>
md: bind<hda3,2>
md: running: <hda3><hdc3>
md: hda3's event counter: 0000002b
md: hdc3's event counter: 0000002b
md: md1: raid array is not clean -- starting background reconstruction
md1: max total readahead window set to 124k
md1: 1 data-disks, max readahead per data-disk: 124k
raid1: device hda3 operational as mirror 0
raid1: device hdc3 operational as mirror 1
raid1: raid set md1 not clean; reconstructing mirrors
raid1: raid set md1 active with 2 out of 2 mirrors
md: updating md1 RAID superblock on device
md: hda3 [events: 0000002c]<6>(write) hda3's sb offset: 38049856
md: syncing RAID array md1
md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc.
md: using maximum available idle IO bandwith (but not more than 100000
KB/sec) for reconstruction.
md: using 124k window, over a total of 38049856 blocks.
md: hdc3 [events: 0000002c]<6>(write) hdc3's sb offset: 38049856
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 152k freed
Executing init=/sbin/init
loop: loaded (max 8 devices)
Adding Swap: 979956k swap-space (priority -1)
Adding Swap: 979956k swap-space (priority -2)
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,0), internal journal
Real Time Clock Driver v1.10f
blk: queue c036c7e0, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c036cc50, I/O limit 4095Mb (mask 0xffffffff)
hdc: Speed warnings UDMA 3/4/5 is not functional.
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU1] (supports C1, 8 throttling states)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
01:00.0: 3Com PCI 3c905C Tornado at 0xdc00. Vers LK1.1.18-ac
00:04:79:66:6a:e8, IRQ 21
product code 464a rev 00.14 date 11-13-00
Internal config register is 1800000, transceivers 0xa.
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
MII transceiver found at address 24, status 782d.
Enabling bus-master transmits and whole-frame receives.
01:00.0: scatter/gather enabled. h/w checksums enabled
divert: allocating divert_blk for eth0
8139too Fast Ethernet driver 0.9.26
divert: allocating divert_blk for eth1
eth1: RealTek RTL8139 at 0xe0a4b800, 00:80:48:38:b6:06, IRQ 22
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
hdc: Speed warnings UDMA 3/4/5 is not functional.
md: md1: sync done.
md: recovery thread got woken up ...
md: recovery thread finished ...
^ permalink raw reply [flat|nested] 6+ messages in thread