* [Hardware] smartctl
@ 2008-01-16 11:11 Andrei Lomov
2008-01-16 19:07 ` Andrey Rahmatullin
2008-02-06 11:14 ` ABATAPA
0 siblings, 2 replies; 6+ messages in thread
From: Andrei Lomov @ 2008-01-16 11:11 UTC (permalink / raw)
To: hardware
С жестким диском, похоже, нелады ...
Пока работает, но диагностика подозрительная.
Посоветуйте, насколько это критично,
сейчас бежать в магазин, или еще потерпит?
# /usr/sbin/smartctl -a /dev/hda
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST3250823A
Serial Number: 5ND0RV7P
Firmware Version: 3.03
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Jan 16 17:05:07 2008 NOVT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has
ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 84) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 058 054 006 Pre-fail Always
- 24580178
3 Spin_Up_Time 0x0003 099 098 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always
- 1688
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000f 077 060 030 Pre-fail Always
- 51790101
9 Power_On_Hours 0x0032 095 095 000 Old_age Always
- 4559
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always
- 1716
194 Temperature_Celsius 0x0022 039 048 000 Old_age Always
- 39 (Lifetime Min/Max 0/15)
195 Hardware_ECC_Recovered 0x001a 058 053 000 Old_age Always
- 24580178
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline
- 1
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline
- 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always
- 0
SMART Error Log Version: 1
ATA Error Count: 83 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 83 occurred at disk power-on lifetime: 3659 hours (152 days + 11
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 52 4d 36 e0 Error: UNC at LBA = 0x00364d52 = 3558738
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 d8 08 4f 4d 36 e0 00 00:00:49.697 READ DMA EXT
25 d8 01 d6 24 01 e0 00 00:00:49.685 READ DMA EXT
25 d8 08 4f 4d 36 e0 00 00:00:49.685 READ DMA EXT
25 d8 01 c8 d3 60 e0 00 00:00:49.684 READ DMA EXT
25 d8 01 00 00 00 e0 00 00:00:49.677 READ DMA EXT
Error 82 occurred at disk power-on lifetime: 3659 hours (152 days + 11
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 52 4d 36 e0 Error: UNC at LBA = 0x00364d52 = 3558738
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 d8 08 4f 4d 36 e0 00 00:00:49.697 READ DMA EXT
25 d8 01 c8 d3 60 e0 00 00:00:49.685 READ DMA EXT
25 d8 01 00 00 00 e0 00 00:00:49.685 READ DMA EXT
25 d8 01 00 00 00 e0 00 00:00:49.684 READ DMA EXT
25 d8 20 81 1b 09 e0 00 00:00:49.677 READ DMA EXT
Error 81 occurred at disk power-on lifetime: 3659 hours (152 days + 11
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 52 4d 36 e0 Error: UNC at LBA = 0x00364d52 = 3558738
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 d8 08 4f 4d 36 e0 00 00:00:45.943 READ DMA EXT
25 d8 08 ef 99 1c e0 00 00:00:45.941 READ DMA EXT
25 d8 08 e7 99 1c e0 00 00:00:45.940 READ DMA EXT
25 d8 08 47 ea 08 e0 00 00:00:45.933 READ DMA EXT
25 d8 08 3f ea 08 e0 00 00:00:45.922 READ DMA EXT
Error 80 occurred at disk power-on lifetime: 3641 hours (151 days + 17
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 52 4d 36 e0 Error: UNC at LBA = 0x00364d52 = 3558738
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 d8 08 4f 4d 36 e0 00 01:04:18.094 READ DMA EXT
25 d8 40 21 18 0b e0 00 01:04:18.093 READ DMA EXT
25 d8 3d 59 1b 0b e0 00 01:04:18.092 READ DMA EXT
35 d8 08 3f 6f 71 e0 00 01:04:18.092 WRITE DMA EXT
25 d8 20 9a 1b 0b e0 00 01:04:18.092 READ DMA EXT
Error 79 occurred at disk power-on lifetime: 3641 hours (151 days + 17
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 52 4d 36 e0 Error: UNC at LBA = 0x00364d52 = 3558738
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 d8 08 4f 4d 36 e0 00 01:03:46.319 READ DMA EXT
25 d8 18 df 6c 0a e0 00 01:03:46.314 READ DMA EXT
35 d8 08 0f 53 0a e0 00 01:03:46.314 WRITE DMA EXT
35 d8 08 1f 4f 0a e0 00 01:03:46.305 WRITE DMA EXT
35 d8 08 97 70 71 e0 00 01:03:46.305 WRITE DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 0
-
# 2 Short offline Completed without error 00% 0
-
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
--
Всего доброго,
А.Л.
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Hardware] smartctl
2008-01-16 11:11 [Hardware] smartctl Andrei Lomov
@ 2008-01-16 19:07 ` Andrey Rahmatullin
2008-01-17 15:33 ` Andrei Lomov
2008-02-06 11:14 ` ABATAPA
1 sibling, 1 reply; 6+ messages in thread
From: Andrey Rahmatullin @ 2008-01-16 19:07 UTC (permalink / raw)
To: hardware
[-- Attachment #1: Type: text/plain, Size: 492 bytes --]
On Wed, Jan 16, 2008 at 05:11:05PM +0600, Andrei Lomov wrote:
> С жестким диском, похоже, нелады ...
> Пока работает, но диагностика подозрительная.
> Посоветуйте, насколько это критично,
> сейчас бежать в магазин, или еще потерпит?
Шлейф менять пробовал?
--
WBR, wRAR (ALT Linux Team)
Powered by the ALT Linux fortune(8):
Я бы предпочёл, чтобы специалисты думали прежде чем обновлять, а все
остальные ставили всё, что есть в updates, даже без анонса.
-- ldv in community@
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 197 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Hardware] smartctl
2008-01-16 19:07 ` Andrey Rahmatullin
@ 2008-01-17 15:33 ` Andrei Lomov
2008-01-17 19:20 ` Andrey Rahmatullin
0 siblings, 1 reply; 6+ messages in thread
From: Andrei Lomov @ 2008-01-17 15:33 UTC (permalink / raw)
To: hardware
Andrey Rahmatullin wrote:
> On Wed, Jan 16, 2008 at 05:11:05PM +0600, Andrei Lomov wrote:
>> С жестким диском, похоже, нелады ...
>> Пока работает, но диагностика подозрительная.
>> Посоветуйте, насколько это критично,
>> сейчас бежать в магазин, или еще потерпит?
> Шлейф менять пробовал?
Еще нет.
Дело может быть в шлейфе?
Шлейф я мог задеть.
--
Всего доброго,
А.Л.
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Hardware] smartctl
2008-01-17 15:33 ` Andrei Lomov
@ 2008-01-17 19:20 ` Andrey Rahmatullin
0 siblings, 0 replies; 6+ messages in thread
From: Andrey Rahmatullin @ 2008-01-17 19:20 UTC (permalink / raw)
To: hardware
[-- Attachment #1: Type: text/plain, Size: 562 bytes --]
On Thu, Jan 17, 2008 at 09:33:36PM +0600, Andrei Lomov wrote:
> Еще нет.
> Дело может быть в шлейфе?
На мой дилетантский взгляд - да.
Кроме того, его быстрее и дешевле поменять.
--
WBR, wRAR (ALT Linux Team)
Powered by the ALT Linux fortune(8):
> > Например, в новом раскладе остается каталог /usr/lib/rpm.
> > Какая здесь логика? Почему не в lib64, и не лучше ли
> > переместить его содержимое в /usr/share/rpm?
мня...может тогда и /usr/X11R6/lib/X11 -> /usr/X11R6/share? :)
и огрести много приятных ночей с этим делом.
-- mouse in devel@
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 197 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Hardware] smartctl
2008-01-16 11:11 [Hardware] smartctl Andrei Lomov
2008-01-16 19:07 ` Andrey Rahmatullin
@ 2008-02-06 11:14 ` ABATAPA
2008-04-01 14:08 ` Andrei Lomov
1 sibling, 1 reply; 6+ messages in thread
From: ABATAPA @ 2008-02-06 11:14 UTC (permalink / raw)
To: hardware
16 января 2008 г. Andrei Lomov написал:
> С жестким диском, похоже, нелады ...
> Пока работает, но диагностика подозрительная.
> Посоветуйте, насколько это критично,
А что именно не понравилось?
--
ABATAPA
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Hardware] smartctl
2008-02-06 11:14 ` ABATAPA
@ 2008-04-01 14:08 ` Andrei Lomov
0 siblings, 0 replies; 6+ messages in thread
From: Andrei Lomov @ 2008-04-01 14:08 UTC (permalink / raw)
To: hardware
ABATAPA wrote:
> 16 января 2008 г. Andrei Lomov написал:
>> С жестким диском, похоже, нелады ...
>> Пока работает, но диагностика подозрительная.
>> Посоветуйте, насколько это критично,
>
> А что именно не понравилось?
>
Ну например,
SMART Error Log Version: 1
ATA Error Count: 83 (device log contains only the most recent five errors)
CR = Command Register [HEX]
--
Всего доброго,
А.Л.
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2008-04-01 14:08 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2008-01-16 11:11 [Hardware] smartctl Andrei Lomov
2008-01-16 19:07 ` Andrey Rahmatullin
2008-01-17 15:33 ` Andrei Lomov
2008-01-17 19:20 ` Andrey Rahmatullin
2008-02-06 11:14 ` ABATAPA
2008-04-01 14:08 ` Andrei Lomov
ALT Linux hardware support
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/hardware/0 hardware/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 hardware hardware/ http://lore.altlinux.org/hardware \
hardware@altlinux.ru hardware@lists.altlinux.org hardware@lists.altlinux.ru hardware@lists.altlinux.com hardware@altlinux.org
public-inbox-index hardware
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.hardware
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git