Linux version 2.4.32-std-up-alt1 (builder@sadist.office.altlinux.org) (gcc version 2.96 20000731 (ALT Linux, build 2.96-alt6)) #1 Mon Dec 26 17:55:19 MSK 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 0000000000096800 (usable) BIOS-e820: 0000000000096800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. found SMP MP-table at 000f5a20 hm, page 000f5000 reserved twice. hm, page 000f6000 reserved twice. hm, page 000f1000 reserved twice. hm, page 000f2000 reserved twice. On node 0 totalpages: 131056 zone(0): 4096 pages. zone(1): 126960 pages. zone(2): 0 pages. DMI 2.3 present. 39 structures occupying 1122 bytes. DMI table at 0x000F0800. BIOS Vendor: Phoenix Technologies, LTD BIOS Version: 6.00 PG BIOS Release: 04/20/2004 System Vendor: Product Name: Version: Serial Number: Board Vendor: Board Name: K8T800-8237 Board Version: ACPI: RSDP (v000 VIAK8 ) @ 0x000f7490 ACPI: RSDT (v001 VIAK8 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000 ACPI: FADT (v001 VIAK8 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040 ACPI: MADT (v001 VIAK8 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff8100 ACPI: DSDT (v001 VIAK8 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 Unknown CPU [15:12] APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) Using ACPI for processor (LAPIC) configuration information Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000 I/O APIC #2 Version 17 at 0xFEC00000. Enabling APIC mode: Flat. Using 1 I/O APICs Processors: 1 Kernel command line: BOOT_IMAGE=linux-up ro root=302 pci=noacpi Initializing CPU#0 Detected 2014.124 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 4010.80 BogoMIPS Memory: 515132k/524224k available (1235k kernel code, 8668k reserved, 512k data, 136k init, 0k highmem) Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode cache hash table entries: 32768 (order: 6, 262144 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 078bfbff e1d3fbff 00000000 00000000 CPU: Common caps: 078bfbff e1d3fbff 00000000 00000000 CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. Looking for DSDT in initrd ... not found! ACPI: IRQ9 SCI: Level Trigger. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs Setting 2 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 2 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-17, 2-18, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 20. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178003 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0003 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 000 00 1 0 0 0 0 0 0 00 06 001 01 0 0 0 0 0 1 1 51 07 001 01 0 0 0 0 0 1 1 59 08 001 01 0 0 0 0 0 1 1 61 09 001 01 0 0 0 0 0 1 1 69 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 001 01 0 0 0 0 0 1 1 71 0d 001 01 0 0 0 0 0 1 1 79 0e 001 01 0 0 0 0 0 1 1 81 0f 001 01 0 0 0 0 0 1 1 89 10 001 01 1 1 0 1 0 1 1 91 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 001 01 1 1 0 1 0 1 1 99 14 001 01 1 1 0 1 0 1 1 A1 15 001 01 1 1 0 1 0 1 1 A9 16 001 01 1 1 0 1 0 1 1 B1 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ19 -> 0:19 IRQ20 -> 0:20 IRQ21 -> 0:21 IRQ22 -> 0:22 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2013.9431 MHz. ..... host bus clock speed is 201.3942 MHz. cpu: 0, clocks: 2013942, slice: 1006971 CPU0 mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel ACPI: Subsystem revision 20040326 PCI: PCI BIOS revision 2.10 entry at 0xfb550, last bus=2 PCI: Using configuration type 1 ACPI-0352: *** Error: Looking up [ATFL] in namespace, AE_NOT_FOUND search_node dffe6560 start_node dffe6560 return_node 00000000 ACPI-1132: *** Error: Method execution failed [\_SB_.PCI0.PATA.CHN1._STA] (Node dffe6560), AE_NOT_FOUND ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: System [ACPI] (supports S0 S1 S4 S5) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Via IRQ fixup ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI-0352: *** Error: Looking up [ATFL] in namespace, AE_NOT_FOUND search_node dffe6560 start_node dffe6560 return_node 00000000 ACPI-1132: *** Error: Method execution failed [\_SB_.PCI0.PATA.CHN1._STA] (Node dffe6560), AE_NOT_FOUND ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *5 ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0 ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled. ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled. ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled. ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled. PCI: Probing PCI hardware PCI: Using IRQ router VIA [1106/3227] at 00:11.0 PCI->APIC IRQ transform: (B0,I8,P0) -> 16 PCI->APIC IRQ transform: (B0,I11,P0) -> 19 PCI->APIC IRQ transform: (B0,I14,P0) -> 21 PCI->APIC IRQ transform: (B0,I15,P1) -> 20 PCI->APIC IRQ transform: (B0,I15,P0) -> 20 PCI->APIC IRQ transform: (B0,I16,P0) -> 21 PCI->APIC IRQ transform: (B0,I16,P2) -> 21 PCI->APIC IRQ transform: (B0,I17,P2) -> 22 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd kinoded started VFS: Disk quotas vdquot_6.5.1 pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A NET4: Frame Diverter 0.46 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 00:0f.1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci00:0f.1 ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:pio, hdd:pio hda: SAMSUNG SV3012H, ATA DISK drive blk: queue c0311e60, I/O limit 4095Mb (mask 0xffffffff) ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: attached ide-disk driver. hda: host protected area => 1 hda: 58711968 sectors (30061 MB) w/2048KiB Cache, CHS=3654/255/63, UDMA(33) Partition check: hda: hda1 hda2 hda4 < hda5 hda6 > md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 275k freed VFS: Mounted root (romfs filesystem) readonly. DAC960: ***** DAC960 RAID Driver Version 2.4.11 of 11 October 2001 ***** DAC960: Copyright 1998-2001 by Leonard N. Zubkoff DAC960#0: Configuring Mylex DAC960PG PCI RAID Controller DAC960#0: Firmware Version: 4.06-0-08, Channels: 3, Memory Size: 16MB DAC960#0: PCI Bus: 0, Device: 8, Function: 1, I/O Address: Unassigned DAC960#0: PCI Address: 0xFD000000 mapped at 0xE081B000, IRQ Channel: 16 DAC960#0: Controller Queue Depth: 64, Maximum Blocks per Command: 128 DAC960#0: Driver Queue Depth: 63, Scatter/Gather Limit: 33 of 33 Segments DAC960#0: Stripe Size: 64KB, Segment Size: 8KB, BIOS Geometry: 255/63 DAC960#0: Physical Devices: DAC960#0: 0:0 Vendor: IBM Model: DDYS-T18350M Revision: S93E DAC960#0: Serial Number: 5EFJY357 DAC960#0: Disk Status: Online, 35842048 blocks DAC960#0: 0:1 Vendor: IBM Model: DDYS-T18350M Revision: S93E DAC960#0: Serial Number: TEFTR544 DAC960#0: Disk Status: Online, 35842048 blocks DAC960#0: 1:0 Vendor: HP 18.2G Model: ATLAS10K3_18_WLS Revision: HP05 DAC960#0: Serial Number: 3TB0A8RK DAC960#0: Disk Status: Online, 35565568 blocks DAC960#0: Logical Drives: DAC960#0: /dev/rd/c0d0: RAID-1, Online, 35565568 blocks, Write Thru DAC960#0: /dev/rd/c0d1: RAID-0, Online, 552960 blocks, Write Back DAC960#0: /dev/rd/c0d2: RAID-7, Online, 35565568 blocks, Write Thru rd/c0d0: unknown partition table rd/c0d1: unknown partition table rd/c0d2: unknown partition table SCSI subsystem driver Revision: 1.00 kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 libata version 1.11 loaded. sata_sil version 0.9 ata1: SATA max UDMA/100 cmd 0xE0846080 ctl 0xE084608A bmdma 0xE0846000 irq 19 ata2: SATA max UDMA/100 cmd 0xE08460C0 ctl 0xE08460CA bmdma 0xE0846008 irq 19 ata1: dev 0 cfg 49:2f00 82:346b 83:7fe9 84:4773 85:3468 86:3c01 87:4763 88:207f ata1: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48 ata1: dev 0 configured for UDMA/100 ata2: dev 0 cfg 49:2f00 82:346b 83:7fe9 84:4773 85:3468 86:3c01 87:4763 88:207f ata2: dev 0 ATA, max UDMA/133, 488395055 sectors: lba48 ata2: dev 0 configured for UDMA/100 scsi0 : sata_sil scsi1 : sata_sil Vendor: ATA Model: HDT722525DLA380 Rev: V44O Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: HDT722525DLA380 Rev: V44O Type: Direct-Access ANSI SCSI revision: 05 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0 SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: sda1 sda2 sda4 < sda5 > SCSI device sdb: 488395055 512-byte hdwr sectors (250058 MB) sdb: sdb1 sdb2 sata_via version 1.1 sata_via(00:0f.0): routed to hard irq line 4 ata3: SATA max UDMA/133 cmd 0xB800 ctl 0xBC02 bmdma 0xC800 irq 20 ata4: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xC808 irq 20 ata3: no device found (phy stat 00000000) ata4: no device found (phy stat 00000000) scsi2 : sata_via scsi3 : sata_via reiserfs: found format "3.6" with standard journal reiserfs: using ordered data mode reiserfs: checking transaction log (device ide0(3,2)) ... for (ide0(3,2)) ide0(3,2):Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Trying to move old root to /initrd ... failed Unmounting old root Trying to free ramdisk memory ... okay Freeing unused kernel memory: 136k freed Executing init=/sbin/init Adding Swap: 1048280k swap-space (priority -1) Real Time Clock Driver v1.10f i2c-core.o: i2c core module version 2.9.2 (20050906) i2c-dev.o: i2c /dev entries driver module version 2.9.2 (20050906) reiserfs: found format "3.6" with standard journal reiserfs: using ordered data mode reiserfs: checking transaction log (device ide0(3,6)) ... for (ide0(3,6)) ide0(3,6):Using r5 hash to sort names reiserfs: found format "3.6" with standard journal reiserfs: using ordered data mode reiserfs: checking transaction log (device ide0(3,5)) ... for (ide0(3,5)) ide0(3,5):Using r5 hash to sort names 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html 00:0e.0: 3Com PCI 3c905C Tornado at 0xb400. Vers LK1.1.18 divert: allocating divert_blk for eth0 i2c-proc.o version 2.9.2 (20050906) eth0: Setting full-duplex based on MII #24 link partner capability of 01e1. i2c-viapro.o version 2.9.2 (20050906) i2c-dev.o: Registered 'SMBus Via Pro adapter at 5000' as minor 0 i2c-isa.o version 2.9.2 (20050906) i2c-dev.o: Registered 'ISA main adapter' as minor 1 eeprom.o version 2.9.2 (20050906) w83627hf.o version 2.9.2 (20050906)