* [Hardware] Чипсет ATi rx330 и Линукс?
@ 2006-03-15 21:53 Alexei V. Mezin
2006-03-16 9:34 ` Sergey Vlasov
0 siblings, 1 reply; 7+ messages in thread
From: Alexei V. Mezin @ 2006-03-15 21:53 UTC (permalink / raw)
To: hardware
У одного знакомого товарища материнская плата на чипсете ATi rx330.
Когда прошлый раз пытался поставить на ту машину Линукс, то все
ставилось, но диски работали с черепашьей скоростью: не более 1-2Мб/с, и
либо трансфер с диска, либо по сети, одновременно никак.
Пришла пора попробовать Линукс на той машине еще раз. Погуглил, но
ничего вразумительного не нашел. На сайте ATi пишут, что суппорт этого
чипсета есть для вин и для Линукса. Но больше нигде, даже в исходниках
ядра, этот суппорт не упоминается.
Может кто сталкивался с этой проблемой?
P.S. Да, знаю что нужно делать с теми, кто покупает платы на таких
чипсетах. Но уже ничего изменить нельзя.
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [Hardware] Чипсет ATi rx330 и Линукс?
2006-03-15 21:53 [Hardware] Чипсет ATi rx330 и Линукс? Alexei V. Mezin
@ 2006-03-16 9:34 ` Sergey Vlasov
2006-03-20 11:52 ` Dmitry Vodennikov
0 siblings, 1 reply; 7+ messages in thread
From: Sergey Vlasov @ 2006-03-16 9:34 UTC (permalink / raw)
To: hardware, alex783
[-- Attachment #1: Type: text/plain, Size: 689 bytes --]
On Thu, Mar 16, 2006 at 12:53:35AM +0300, Alexei V. Mezin wrote:
> У одного знакомого товарища материнская плата на чипсете ATi rx330.
> Когда прошлый раз пытался поставить на ту машину Линукс, то все
> ставилось, но диски работали с черепашьей скоростью: не более 1-2Мб/с, и
> либо трансфер с диска, либо по сети, одновременно никак.
>
> Пришла пора попробовать Линукс на той машине еще раз. Погуглил, но
> ничего вразумительного не нашел. На сайте ATi пишут, что суппорт этого
> чипсета есть для вин и для Линукса. Но больше нигде, даже в исходниках
> ядра, этот суппорт не упоминается.
Какие дистрибутивы, какое ядро пробовали?
Покажите вывод lspci -vvx и dmesg.
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [Hardware] Чипсет ATi rx330 и Линукс?
2006-03-16 9:34 ` Sergey Vlasov
@ 2006-03-20 11:52 ` Dmitry Vodennikov
2006-03-20 13:54 ` Sergey Vlasov
0 siblings, 1 reply; 7+ messages in thread
From: Dmitry Vodennikov @ 2006-03-20 11:52 UTC (permalink / raw)
To: hardware
Sergey Vlasov пишет:
> On Thu, Mar 16, 2006 at 12:53:35AM +0300, Alexei V. Mezin wrote:
>> У одного знакомого товарища материнская плата на чипсете ATi rx330.
>> Когда прошлый раз пытался поставить на ту машину Линукс, то все
>> ставилось, но диски работали с черепашьей скоростью: не более 1-2Мб/с, и
>> либо трансфер с диска, либо по сети, одновременно никак.
>>
>> Пришла пора попробовать Линукс на той машине еще раз. Погуглил, но
>> ничего вразумительного не нашел. На сайте ATi пишут, что суппорт этого
>> чипсета есть для вин и для Линукса. Но больше нигде, даже в исходниках
>> ядра, этот суппорт не упоминается.
>
> Какие дистрибутивы, какое ядро пробовали?
>
> Покажите вывод lspci -vvx и dmesg.
Можно я сюда же? Вечером доберусь до ноутбука и покажу свой lscpi.
Появился IBM Thinkpad R51e, ibm product number если не путаю 1843-6KG
Судя по lspci чипсет внутри именно ATI.
Система ALM24, ядро - последнее из updates - 2.4.26-std-up-alt13
Я так понимаю, что из-за того, что ядро достаточно старое, есть проблемы
с включением dma-режимов в чипсете (сам диск по hdparm говорит, что он
вполне может давать udma5). Отсюда и черепашья скорость - у меня 1Мб/с
Естественно, не поднимаются ни сетевая, ни модем, ни звук.
Сетевую карту удалось поднять, собрав из сизифа последние драйвера
broadcom.
Теперь вот думаю, что делать дальше...
попробовать ata_piix, которые по слухам нормально работатют с dma, и
взять необходимые мне свежие драйвера из сизифа?
взять более свежее ядро, которое нормально встанет в master 2.4?
поставить compact 3.0?
Linux используется в основном как полигон для обкатки решений под
серверные инсталляции master 2.4
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [Hardware] Чипсет ATi rx330 и Линукс?
2006-03-20 11:52 ` Dmitry Vodennikov
@ 2006-03-20 13:54 ` Sergey Vlasov
2006-03-20 16:08 ` vod
0 siblings, 1 reply; 7+ messages in thread
From: Sergey Vlasov @ 2006-03-20 13:54 UTC (permalink / raw)
To: hardware
[-- Attachment #1: Type: text/plain, Size: 1854 bytes --]
On Mon, Mar 20, 2006 at 03:52:45AM -0800, Dmitry Vodennikov wrote:
> Можно я сюда же? Вечером доберусь до ноутбука и покажу свой lscpi.
> Появился IBM Thinkpad R51e, ibm product number если не путаю 1843-6KG
> Судя по lspci чипсет внутри именно ATI.
>
> Система ALM24, ядро - последнее из updates - 2.4.26-std-up-alt13
> Я так понимаю, что из-за того, что ядро достаточно старое, есть проблемы
> с включением dma-режимов в чипсете (сам диск по hdparm говорит, что он
> вполне может давать udma5). Отсюда и черепашья скорость - у меня 1Мб/с
> Естественно, не поднимаются ни сетевая, ни модем, ни звук.
> Сетевую карту удалось поднять, собрав из сизифа последние драйвера
> broadcom.
> Теперь вот думаю, что делать дальше...
> попробовать ata_piix, которые по слухам нормально работатют с dma, и
> взять необходимые мне свежие драйвера из сизифа?
ata_piix предназначен несколько для другого - для поддержки Serial ATA на
Intel ICH5/6/...; контроллеры ATI он не поддерживает. Вообще в драйверах
libata в ядрах, имеющихся сейчас в Сизифе, поддержка PATA не включена
(хотя некоторые производители ноутбуков в последнее время подключают диски
по SATA, устанавливая для этого мост SATA-PATA).
> взять более свежее ядро, которое нормально встанет в master 2.4?
> поставить compact 3.0?
Тот же вопрос - покажите lspci -vvx и dmesg, дальше уже можно будет
смотреть, что это конкретно за железо и в каких версиях ядра
поддерживается.
> Linux используется в основном как полигон для обкатки решений под
> серверные инсталляции master 2.4
Если стоит именно такая задача, тогда, возможно, имеет смысл ограничить
обновления относительно M24 до минимума - например, если окажется, что
нужный контроллер поддерживается в ядре 2.4.32, ставить именно его, а не
2.6.x (либо вообще сделать backport нужного драйвера в 2.4.26).
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [Hardware] Чипсет ATi rx330 и Линукс?
2006-03-20 13:54 ` Sergey Vlasov
@ 2006-03-20 16:08 ` vod
2006-03-20 17:57 ` Sergey Vlasov
0 siblings, 1 reply; 7+ messages in thread
From: vod @ 2006-03-20 16:08 UTC (permalink / raw)
To: hardware
[-- Attachment #1: Type: text/plain, Size: 2070 bytes --]
Sergey Vlasov пишет:
> On Mon, Mar 20, 2006 at 03:52:45AM -0800, Dmitry Vodennikov wrote:
>> Можно я сюда же? Вечером доберусь до ноутбука и покажу свой lscpi.
>> Появился IBM Thinkpad R51e, ibm product number если не путаю 1843-6KG
>> Судя по lspci чипсет внутри именно ATI.
>>
>> Система ALM24, ядро - последнее из updates - 2.4.26-std-up-alt13
>> Я так понимаю, что из-за того, что ядро достаточно старое, есть проблемы
>> с включением dma-режимов в чипсете (сам диск по hdparm говорит, что он
>> вполне может давать udma5). Отсюда и черепашья скорость - у меня 1Мб/с
>> Естественно, не поднимаются ни сетевая, ни модем, ни звук.
>> Сетевую карту удалось поднять, собрав из сизифа последние драйвера
>> broadcom.
>> Теперь вот думаю, что делать дальше...
>> попробовать ata_piix, которые по слухам нормально работатют с dma, и
>> взять необходимые мне свежие драйвера из сизифа?
>
> ata_piix предназначен несколько для другого - для поддержки Serial ATA на
> Intel ICH5/6/...; контроллеры ATI он не поддерживает. Вообще в драйверах
> libata в ядрах, имеющихся сейчас в Сизифе, поддержка PATA не включена
> (хотя некоторые производители ноутбуков в последнее время подключают диски
> по SATA, устанавливая для этого мост SATA-PATA).
>> взять более свежее ядро, которое нормально встанет в master 2.4?
>> поставить compact 3.0?
>
> Тот же вопрос - покажите lspci -vvx и dmesg, дальше уже можно будет
> смотреть, что это конкретно за железо и в каких версиях ядра
> поддерживается.
Вот пожалуйста. В аттачах lspci и dmesg.
>> Linux используется в основном как полигон для обкатки решений под
>> серверные инсталляции master 2.4
>
> Если стоит именно такая задача, тогда, возможно, имеет смысл ограничить
> обновления относительно M24 до минимума - например, если окажется, что
> нужный контроллер поддерживается в ядре 2.4.32, ставить именно его, а не
> 2.6.x (либо вообще сделать backport нужного драйвера в 2.4.26).
Пока склоняюсь к этому варианту.
Либо брать из сизифа 2.4.32, либо делать бэкпорт драйверов. Вот только
что предпочесть пока не знаю.
[-- Attachment #2: lspci.log --]
[-- Type: text/plain, Size: 13525 bytes --]
00:00.0 Host bridge: ATI Technologies Inc: Unknown device 5a31 (rev 01)
Subsystem: IBM: Unknown device 0585
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
00: 02 10 31 5a 06 01 20 22 01 00 00 06 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 85 05
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: ATI Technologies Inc: Unknown device 5a3f (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00009000-00009fff
Memory behind bridge: c0100000-c01fffff
Prefetchable memory behind bridge: d4000000-d7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [b0] #0d [0000]
00: 02 10 3f 5a 07 01 30 02 00 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 40 91 91 20 22
20: 10 c0 10 c0 00 d4 f0 d7 00 00 00 00 00 00 00 00
30: 00 00 00 00 b0 00 00 00 00 00 00 00 ff 00 0c 00
00:04.0 PCI bridge: ATI Technologies Inc: Unknown device 5a36 (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, cache line size 08
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: c0200000-c02fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #10 [0041]
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] #0d [0000]
Capabilities: [b8] #08 [a803]
00: 02 10 36 5a 07 01 10 00 00 00 04 06 08 00 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 f1 01 00 20
20: 20 c0 20 c0 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 04 00
00:06.0 PCI bridge: ATI Technologies Inc: Unknown device 5a38 (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00000000-00000fff
Memory behind bridge: 00000000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #10 [0041]
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] #0d [0000]
Capabilities: [b8] #08 [a803]
00: 02 10 38 5a 00 01 10 00 00 00 04 06 08 00 01 00
10: 00 00 00 00 00 00 00 00 00 03 03 00 01 01 00 00
20: 00 00 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 04 00
00:13.0 USB Controller: ATI Technologies Inc: Unknown device 4374 (prog-if 10 [OHCI])
Subsystem: IBM: Unknown device 058f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
00: 02 10 74 43 17 01 b0 02 00 10 03 0c 08 40 80 00
10: 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 8f 05
30: 00 00 00 00 d0 00 00 00 00 00 00 00 0b 01 00 00
00:13.1 USB Controller: ATI Technologies Inc: Unknown device 4375 (prog-if 10 [OHCI])
Subsystem: IBM: Unknown device 0590
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at c0001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
00: 02 10 75 43 17 01 b0 02 00 10 03 0c 08 40 00 00
10: 00 10 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 90 05
30: 00 00 00 00 d0 00 00 00 00 00 00 00 0b 01 00 00
00:13.2 USB Controller: ATI Technologies Inc: Unknown device 4373 (prog-if 20 [EHCI])
Subsystem: IBM: Unknown device 0591
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin A routed to IRQ 9
Region 0: Memory at c0002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
00: 02 10 73 43 17 01 b0 02 00 20 03 0c 08 40 00 00
10: 00 20 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 91 05
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 00 00
00:14.0 SMBus: ATI Technologies Inc: Unknown device 4372 (rev 11)
Subsystem: IBM: Unknown device 0592
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: I/O ports at 8040 [size=16]
Region 1: Memory at c0003000 (32-bit, non-prefetchable) [size=1K]
00: 02 10 72 43 03 01 20 02 11 00 05 0c 00 00 80 00
10: 41 80 00 00 00 30 00 c0 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 92 05
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:14.1 IDE interface: ATI Technologies Inc: Unknown device 4376 (prog-if 8a [Master SecP PriP])
Subsystem: IBM: Unknown device 0593
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 8410 [size=16]
Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
00: 02 10 76 43 05 00 30 02 00 8a 01 01 00 00 00 00
10: f1 01 00 00 f5 03 00 00 71 01 00 00 75 03 00 00
20: 11 84 00 00 00 00 00 00 00 00 00 00 14 10 93 05
30: 00 00 00 00 70 00 00 00 00 00 00 00 ff 01 00 00
00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 4377
Subsystem: IBM: Unknown device 0594
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 02 10 77 43 0f 01 20 02 00 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 94 05
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4371 (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=04, subordinate=08, sec-latency=64
I/O behind bridge: 0000a000-0000dfff
Memory behind bridge: c0300000-cfffffff
Prefetchable memory behind bridge: d8000000-dfffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00: 02 10 71 43 07 01 a0 02 00 01 04 06 00 40 81 00
10: 00 00 00 00 00 00 00 00 00 04 08 40 a1 d1 80 22
20: 30 c0 f0 cf 00 d8 f0 df 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00
00:14.5 Multimedia audio controller: ATI Technologies Inc: Unknown device 4370 (rev 02)
Subsystem: IBM: Unknown device 0586
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min), cache line size 08
Interrupt: pin B routed to IRQ 17
Region 0: Memory at c0003400 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
00: 02 10 70 43 17 01 30 04 02 00 01 04 08 40 80 00
10: 00 34 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 86 05
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 02 02 00
00:14.6 Modem: ATI Technologies Inc: Unknown device 4378 (rev 02) (prog-if 00 [Generic])
Subsystem: IBM: Unknown device 0587
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min), cache line size 08
Interrupt: pin B routed to IRQ 17
Region 0: Memory at c0003800 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
00: 02 10 78 43 17 01 30 04 02 00 03 07 08 40 80 00
10: 00 38 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 87 05
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 02 02 00
01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5a62 (prog-if 00 [VGA])
Subsystem: IBM: Unknown device 059d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d4000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
00: 02 10 62 5a 07 01 b0 02 00 00 00 03 08 42 00 00
10: 08 00 00 d4 01 90 00 00 00 00 10 c0 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 9d 05
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 08 00
02:00.0 Ethernet controller: Broadcom Corporation: Unknown device 167e (rev 21)
Subsystem: IBM: Unknown device 057d
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c0200000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 4289420522609050 Data: e488
Capabilities: [d0] #10 [0001]
00: e4 14 7e 16 02 01 10 00 21 00 00 02 08 00 00 00
10: 04 00 20 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 07 00 00 00 14 10 7d 05
30: 00 00 00 00 48 00 00 00 00 00 00 00 0b 01 00 00
04:00.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus Controller
Subsystem: Midas lab Inc: Unknown device 0528
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 20
Region 0: Memory at c0300000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=04, secondary=06, subordinate=08, sec-latency=176
Memory window 0: 10000000-103ff000 (prefetchable)
Memory window 1: 10400000-107ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00: 4c 10 56 ac 07 00 10 02 00 00 07 06 08 a8 02 00
10: 00 00 30 c0 a0 00 00 02 04 06 08 b0 00 00 00 10
20: 00 f0 3f 10 00 00 40 10 00 f0 7f 10 00 40 00 00
30: fc 40 00 00 00 44 00 00 fc 44 00 00 0b 01 c0 05
40: 10 14 28 05 01 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[-- Attachment #3: dmesg.log --]
[-- Type: text/plain, Size: 14797 bytes --]
Linux version 2.4.26-std-up-alt13 (builder@mash.office.altlinux.ru) (gcc version 2.96 20000731 (ALT Linux, build 2.96-alt6)) #1 Mon Nov 14 00:25:14 MSK 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000099000 (usable)
BIOS-e820: 0000000000099000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000dee0000 (usable)
BIOS-e820: 000000000dee0000 - 000000000deeb000 (ACPI data)
BIOS-e820: 000000000deeb000 - 000000000df00000 (ACPI NVS)
BIOS-e820: 000000000df00000 - 000000000e000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
0MB HIGHMEM available.
222MB LOWMEM available.
On node 0 totalpages: 57056
zone(0): 4096 pages.
zone(1): 52960 pages.
zone(2): 0 pages.
DMI present.
59 structures occupying 1940 bytes.
DMI table at 0x000E0010.
BIOS Vendor: IBM
BIOS Version: 78ET35WW (1.06 )
BIOS Release: 09/30/2005
System Vendor: IBM
Product Name: 18436KG
Version: ThinkPad R51e
Serial Number: L3D5493
Board Vendor: IBM
Board Name: 18436KG
Board Version: Not Available
IBM machine detected. Enabling interrupts during APM calls.
ACPI: RSDP (v002 IBM ) @ 0x000f6eb0
ACPI: XSDT (v001 IBM TP-78 0x00001060 LTP 0x00000000) @ 0x0dee1879
ACPI: FADT (v003 IBM TP-78 0x00001060 IBM 0x00000001) @ 0x0dee1900
ACPI: SSDT (v001 IBM TP-78 0x00001060 MSFT 0x0100000e) @ 0x0dee1ab4
ACPI: ECDT (v001 IBM TP-78 0x00001060 IBM 0x00000001) @ 0x0deeada2
ACPI: MADT (v001 IBM TP-78 0x00001060 IBM 0x00000001) @ 0x0deeadf4
ACPI: MCFG (v001 IBM TP-78 0x00001060 IBM 0x00000001) @ 0x0deeae4e
ACPI: BOOT (v001 IBM TP-78 0x00001060 LTP 0x00000001) @ 0x0deeafd8
ACPI: DSDT (v001 IBM TP-78 0x00001060 MSFT 0x0100000e) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 Pentium(tm) Pro APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 1
IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
Using ACPI (MADT) for SMP configuration information
Kernel command line: auto BOOT_IMAGE=2426-std-up-13 ro root=306
Initializing CPU#0
Detected 1496.274 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 2981.88 BogoMIPS
Memory: 222784k/228224k available (1238k kernel code, 5028k reserved, 509k data, 136k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 32K, L1 D cache: 32K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: afe9fbff 00100000 00000000 00000000
CPU: Common caps: afe9fbff 00100000 00000000 00000000
CPU: Intel(R) Celeron(R) M processor 1.50GHz stepping 08
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-22, 1-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1496.2916 MHz.
..... host bus clock speed is 99.7528 MHz.
cpu: 0, clocks: 997528, slice: 498764
CPU0<T0:997520,T1:498752,D:4,S:498764,C:997528>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20040326
PCI: PCI BIOS revision 2.10 entry at 0xfd7bd, last bus=8
PCI: Using configuration type 1
Looking for DSDT in initrd ... not found!
ACPI: Found ECDT
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S3 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:14.1
Transparent bridge - PCI device 1002:4371 (ATI Technologies Inc)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
ACPI: Embedded Controller [EC] (gpe 3)
ACPI: Power Resource [PUBS] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
PCI: Probing PCI hardware
00:00:13[A] -> 1-9 -> IRQ 9 level low
00:00:14[A] -> 1-16 -> IRQ 16 level low
00:00:14[B] -> 1-17 -> IRQ 17 level low
00:00:14[C] -> 1-18 -> IRQ 18 level low
00:02:00[D] -> 1-19 -> IRQ 19 level low
00:04:00[A] -> 1-20 -> IRQ 20 level low
00:04:00[B] -> 1-23 -> IRQ 23 level low
00:04:02[A] -> 1-22 -> IRQ 22 level low
number of MP IRQ sources: 16.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178021
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0021
An unexpected IO-APIC was found. If this kernel release is less than
three months old please report this to linux-smp@vger.kernel.org
.... register #02: 01000000
....... : arbitration: 01
.... register #03: 01178021
....... : Boot DT : 1
An unexpected IO-APIC was found. If this kernel release is less than
three months old please report this to linux-smp@vger.kernel.org
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 1 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 1 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 B1
11 001 01 1 1 0 1 0 1 1 B9
12 001 01 1 1 0 1 0 1 1 C1
13 001 01 1 1 0 1 0 1 1 C9
14 001 01 1 1 0 1 0 1 1 D1
15 001 01 0 1 0 1 0 1 1 A9
16 001 01 1 1 0 1 0 1 1 E1
17 001 01 1 1 0 1 0 1 1 D9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
kinoded started
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xd4000000, mapped to 0xce813000, size 1875k
vesafb: mode is 800x600x16, linelength=1600, pages=33
vesafb: protected mode interface info at c000:5191
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture.... found (800x600, 42776 bytes, v2).
Console: switching to colour frame buffer device 82x26
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: HTS541040G9AT00, ATA DISK drive
hdc: HL-DT-STCD-RW/DVD DRIVE GCC-4244N, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 78140160 sectors (40008 MB) w/7539KiB Cache, CHS=5168/240/63
Partition check:
hda: hda1 hda2 hda3 < hda5 hda6 >
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 141k freed
VFS: Mounted root (romfs filesystem) readonly.
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 136k freed
Executing init=/sbin/init
Adding Swap: 536720k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
Real Time Clock Driver v1.10f
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: RW/DVD GCC-4244N Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [AC] (off-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU] (supports C1 C2 C3, 8 throttling states)
MSDOS FS: IO charset cp1251
MSDOS FS: Using codepage 866
subfs: subfs-2.4 version 0.9.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xceaab000, IRQ 9
usb-ohci.c: usb-00:13.0, PCI device 1002:4374 (ATI Technologies Inc)
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 4 ports detected
usb-ohci.c: USB OHCI at membase 0xceaad000, IRQ 9
usb-ohci.c: usb-00:13.1, PCI device 1002:4375 (ATI Technologies Inc)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 4 ports detected
ehci_hcd 00:13.2: PCI device 1002:4373 (ATI Technologies Inc)
ehci_hcd 00:13.2: irq 9, pci mem ceab5000
usb.c: new USB bus registered, assigned bus number 3
ehci_hcd 00:13.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
usb.c: USB disconnect on device 00:13.0-0 address 1
usb.c: USB bus 1 deregistered
usb.c: USB disconnect on device 00:13.1-0 address 1
usb.c: USB bus 2 deregistered
ehci_hcd 00:13.2: remove state 3
usb.c: USB disconnect on device 00:13.2-0 address 1
usb.c: USB bus 3 deregistered
usb.c: deregistering driver usbdevfs
usb.c: deregistering driver hub
parport0: PC-style at 0x3bc [PCSPP,TRISTATE]
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
Yenta ISA IRQ mask 0x0cf8, PCI irq 20
Socket status: 30000007
divert: not allocating divert_blk for non-ethernet device irlan0
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci_hcd 00:13.2: PCI device 1002:4373 (ATI Technologies Inc)
ehci_hcd 00:13.2: irq 9, pci mem cebe6000
usb.c: new USB bus registered, assigned bus number 1
ehci_hcd 00:13.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
usb-ohci.c: USB OHCI at membase 0xcebee000, IRQ 9
usb-ohci.c: usb-00:13.0, PCI device 1002:4374 (ATI Technologies Inc)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 4 ports detected
usb-ohci.c: USB OHCI at membase 0xcebf0000, IRQ 9
usb-ohci.c: usb-00:13.1, PCI device 1002:4375 (ATI Technologies Inc)
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 4 ports detected
Looking for splash picture.... found (800x600, 11408 bytes, v2).
Splash status on console 0 changed to on
Looking for splash picture.... found (800x600, 11408 bytes, v2).
Splash status on console 1 changed to on
Looking for splash picture.... found (800x600, 11408 bytes, v2).
Splash status on console 2 changed to on
Looking for splash picture.... found (800x600, 11408 bytes, v2).
Splash status on console 3 changed to on
Looking for splash picture.... found (800x600, 11408 bytes, v2).
Splash status on console 4 changed to on
Looking for splash picture.... found (800x600, 11408 bytes, v2).
Splash status on console 5 changed to on
Looking for splash picture.... found (800x600, 11408 bytes, v2).
Splash status on console 6 changed to on
Looking for splash picture.... found (800x600, 11408 bytes, v2).
Splash status on console 7 changed to on
Looking for splash picture.... found (800x600, 11408 bytes, v2).
Splash status on console 8 changed to on
Looking for splash picture.... found (800x600, 11408 bytes, v2).
Splash status on console 9 changed to on
Looking for splash picture.... found (800x600, 11408 bytes, v2).
Splash status on console 10 changed to on
Looking for splash picture.... found (800x600, 11408 bytes, v2).
Splash status on console 11 changed to on
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [Hardware] Чипсет ATi rx330 и Линукс?
2006-03-20 16:08 ` vod
@ 2006-03-20 17:57 ` Sergey Vlasov
2006-03-21 4:23 ` Dmitry Vodennikov
0 siblings, 1 reply; 7+ messages in thread
From: Sergey Vlasov @ 2006-03-20 17:57 UTC (permalink / raw)
To: hardware
[-- Attachment #1: Type: text/plain, Size: 904 bytes --]
On Mon, Mar 20, 2006 at 09:08:51PM +0500, vod@elecom.ru wrote:
> 00:14.1 IDE interface: ATI Technologies Inc: Unknown device 4376 (prog-if 8a [Master SecP PriP])
Можете не спешить качать из сизифа 2.4.32 - этого ID нет даже там,
нужно тащить ещё более свежий патч.
> 00:14.5 Multimedia audio controller: ATI Technologies Inc: Unknown device 4370 (rev 02)
> 00:14.6 Modem: ATI Technologies Inc: Unknown device 4378 (rev 02) (prog-if 00 [Generic])
Тут нужны свежие версии alsa и slmodem (впрочем, если там кодек
Conexant, slmodem не поможет).
> 01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5a62 (prog-if 00 [VGA])
RADEON XPRESS 200M (RC410 5A62) - для получения 3D нужен достаточно
свежий fglrx, в свободных драйверах поддержка 3D пока отсутствует.
> 02:00.0 Ethernet controller: Broadcom Corporation: Unknown device 167e (rev 21)
Есть в tg3 в 2.4.32.
[-- Attachment #2: Type: application/pgp-signature, Size: 191 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [Hardware] Чипсет ATi rx330 и Линукс?
2006-03-20 17:57 ` Sergey Vlasov
@ 2006-03-21 4:23 ` Dmitry Vodennikov
0 siblings, 0 replies; 7+ messages in thread
From: Dmitry Vodennikov @ 2006-03-21 4:23 UTC (permalink / raw)
To: hardware
Sergey Vlasov пишет:
> On Mon, Mar 20, 2006 at 09:08:51PM +0500, vod@elecom.ru wrote:
>> 00:14.1 IDE interface: ATI Technologies Inc: Unknown device 4376 (prog-if 8a [Master SecP PriP])
>
> Можете не спешить качать из сизифа 2.4.32 - этого ID нет даже там,
> нужно тащить ещё более свежий патч.
>
Эх...
Спасибо за пояснения.
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2006-03-21 4:23 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2006-03-15 21:53 [Hardware] Чипсет ATi rx330 и Линукс? Alexei V. Mezin
2006-03-16 9:34 ` Sergey Vlasov
2006-03-20 11:52 ` Dmitry Vodennikov
2006-03-20 13:54 ` Sergey Vlasov
2006-03-20 16:08 ` vod
2006-03-20 17:57 ` Sergey Vlasov
2006-03-21 4:23 ` Dmitry Vodennikov
ALT Linux hardware support
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/hardware/0 hardware/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 hardware hardware/ http://lore.altlinux.org/hardware \
hardware@altlinux.ru hardware@lists.altlinux.org hardware@lists.altlinux.ru hardware@lists.altlinux.com hardware@altlinux.org
public-inbox-index hardware
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.hardware
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git