* [Hardware] На какое устройство повесилась USB-флэшка?
@ 2006-01-28 11:22 denis yatsutko
2006-01-28 16:31 ` Michael Shigorin
0 siblings, 1 reply; 5+ messages in thread
From: denis yatsutko @ 2006-01-28 11:22 UTC (permalink / raw)
To: hardware
Надо смонтировать вручную флэш-плейер. Автоматически давно ничего не
монтируется, ну да ладно.
В fstab у меня прописано монтировать sdb1 в /mnt/flash/ и sda1 в
/mnt/storage/. Втыкаю плейер в тот же разъем, в который недавно втыкал
фотоаппарат (тот вешался на sdb1), набираю /mount/flash/ - хрен. Пишет:
mount: /dev/sdb1 is not a valid block device.
Провил плейер на работе на макинтоше - всё нормально монтируется как
внешний диск с фат32. Так я, вот, думаю, может, он не на sdb1 стал, а
ещё куда. Как это определить? more /proc/bus/usb/devices говорит:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 3
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB OHCI Root Hub
S: SerialNumber=e0bd7000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 11 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=04e8 ProdID=5026 Rev=10.01
S: Manufacturer=Samsung
S: Product=YP-MT6
S: SerialNumber=0002F67B1946098A
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 3
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
dmesg говорит:
hub.c: new USB device 00:02.1-2, assigned address 11
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 11
sdb: Unit Not Ready, sense:
Info fld=0xa00 (nonstd), Current 00:00: sense key Not Ready
sdb : READ CAPACITY failed.
sdb : status = 1, message = 00, host = 0, driver = 08
Info fld=0xa00 (nonstd), Current sd00:00: sense key Not Ready
sdb : block size assumed to be 512 bytes, disk size 1GB.
sdb: test WP failed, assume Write Enabled
sdb: I/O error: dev 08:10, sector 0
I/O error: dev 08:10, sector 0
ldm_validate_partition_table(): Disk read failed.
I/O error: dev 08:10, sector 0
unable to read partition table
Подскажите, где искать. Спасибо.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [Hardware] На какое устройство повесилась USB-флэшка?
2006-01-28 11:22 [Hardware] На какое устройство повесилась USB-флэшка? denis yatsutko
@ 2006-01-28 16:31 ` Michael Shigorin
2006-01-30 5:28 ` Re[2]: " Yakov Reztsov
2006-01-30 10:26 ` [Hardware] На " Andrei Bulava
0 siblings, 2 replies; 5+ messages in thread
From: Michael Shigorin @ 2006-01-28 16:31 UTC (permalink / raw)
To: hardware
On Sat, Jan 28, 2006 at 02:22:03PM +0300, denis yatsutko wrote:
> USB Mass Storage device found at 11
> sdb: Unit Not Ready, sense:
> Info fld=0xa00 (nonstd), Current 00:00: sense key Not Ready
> sdb : READ CAPACITY failed.
^^^^^^^^^^^^^^^^^^^^
> sdb : status = 1, message = 00, host = 0, driver = 08
> Info fld=0xa00 (nonstd), Current sd00:00: sense key Not Ready
> sdb : block size assumed to be 512 bytes, disk size 1GB.
> sdb: test WP failed, assume Write Enabled
> sdb: I/O error: dev 08:10, sector 0
> I/O error: dev 08:10, sector 0
> ldm_validate_partition_table(): Disk read failed.
> I/O error: dev 08:10, sector 0
> unable to read partition table
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> Подскажите, где искать. Спасибо.
Я бы гуглил, не припомню такого. (плюс "usb flash")
--
---- WBR, Michael Shigorin <mike@altlinux.ru>
------ Linux.Kiev http://www.linux.kiev.ua/
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re[2]: [Hardware] На какое устройство повесилась USB-флэшка?
2006-01-28 16:31 ` Michael Shigorin
@ 2006-01-30 5:28 ` Yakov Reztsov
2006-01-30 7:16 ` Re[3]: [Hardware]На " Denis Yatsutko
2006-01-30 10:26 ` [Hardware] На " Andrei Bulava
1 sibling, 1 reply; 5+ messages in thread
From: Yakov Reztsov @ 2006-01-30 5:28 UTC (permalink / raw)
To: hardware, shigorin
>
> On Sat, Jan 28, 2006 at 02:22:03PM +0300, denis yatsutko wrote:
> > USB Mass Storage device found at 11
> > sdb: Unit Not Ready, sense:
> > Info fld=0xa00 (nonstd), Current 00:00: sense key Not Ready
> > sdb : READ CAPACITY failed.
> ^^^^^^^^^^^^^^^^^^^^
> > sdb : status = 1, message = 00, host = 0, driver = 08
> > Info fld=0xa00 (nonstd), Current sd00:00: sense key Not Ready
> > sdb : block size assumed to be 512 bytes, disk size 1GB.
> > sdb: test WP failed, assume Write Enabled
> > sdb: I/O error: dev 08:10, sector 0
> > I/O error: dev 08:10, sector 0
> > ldm_validate_partition_table(): Disk read failed.
> > I/O error: dev 08:10, sector 0
> > unable to read partition table
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> > Подскажите, где искать. Спасибо.
>
> Я бы гуглил, не припомню такого. (плюс "usb flash")
>
Была проблема с подключением новой флэшки Transcend (пустой)
с похожей ошибкой (невозможно определить объем)
После записи файлов на другом компьютере
в ALM 2.4 flash смонтировалась и прочиталась без проблем
--
Yakov Reztsov
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re[3]: [Hardware]На какое устройство повесилась USB-флэшка?
2006-01-30 5:28 ` Re[2]: " Yakov Reztsov
@ 2006-01-30 7:16 ` Denis Yatsutko
0 siblings, 0 replies; 5+ messages in thread
From: Denis Yatsutko @ 2006-01-30 7:16 UTC (permalink / raw)
To: hardware, Yakov Reztsov
> > > sdb : READ CAPACITY failed.
> > ^^^^^^^^^^^^^^^^^^^^
> > > sdb : status = 1, message = 00, host = 0, driver = 08
> > > I/O error: dev 08:10, sector 0
> > > unable to read partition table
> > ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> > > Подскажите, где искать. Спасибо.
> > Я бы гуглил, не припомню такого. (плюс "usb flash")
> Была проблема с подключением новой флэшки Transcend (пустой)
> с похожей ошибкой (невозможно определить объем)
У меня флэшка с файлами, записанными на этом самом компьютере (который 2.4).
Самое интересное, что попытки с десятой всё смонтировалось и определилось. На sda1.
Не понимаю.
---
http://denisbooks.lenin.ru
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [Hardware] На какое устройство повесилась USB-флэшка?
2006-01-28 16:31 ` Michael Shigorin
2006-01-30 5:28 ` Re[2]: " Yakov Reztsov
@ 2006-01-30 10:26 ` Andrei Bulava
1 sibling, 0 replies; 5+ messages in thread
From: Andrei Bulava @ 2006-01-30 10:26 UTC (permalink / raw)
To: hardware
Michael Shigorin wrote:
> On Sat, Jan 28, 2006 at 02:22:03PM +0300, denis yatsutko wrote:
>
>>USB Mass Storage device found at 11
>>sdb: Unit Not Ready, sense:
>>Info fld=0xa00 (nonstd), Current 00:00: sense key Not Ready
>>sdb : READ CAPACITY failed.
>
> ^^^^^^^^^^^^^^^^^^^^
>
>>sdb : status = 1, message = 00, host = 0, driver = 08
>>Info fld=0xa00 (nonstd), Current sd00:00: sense key Not Ready
>>sdb : block size assumed to be 512 bytes, disk size 1GB.
>>sdb: test WP failed, assume Write Enabled
>> sdb: I/O error: dev 08:10, sector 0
>> I/O error: dev 08:10, sector 0
>>ldm_validate_partition_table(): Disk read failed.
>> I/O error: dev 08:10, sector 0
>> unable to read partition table
>
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
>
>>Подскажите, где искать. Спасибо.
>
>
> Я бы гуглил, не припомню такого. (плюс "usb flash")
Я припоминаю: такое с usb flash philips, где "из коробки" нет таблицы
разделов, а файловая система прямо на (в моём случае) /dev/sda. В
Winblows XP, ALM 2.4 и ALT Linux Sisyphus работает без проблем.
Так что, в вашем случае, пробуйте 'mount /dev/sdb foo' - счастья не
может не быть :-)
--
// AB1002-UANIC
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2006-01-30 10:26 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2006-01-28 11:22 [Hardware] На какое устройство повесилась USB-флэшка? denis yatsutko
2006-01-28 16:31 ` Michael Shigorin
2006-01-30 5:28 ` Re[2]: " Yakov Reztsov
2006-01-30 7:16 ` Re[3]: [Hardware]На " Denis Yatsutko
2006-01-30 10:26 ` [Hardware] На " Andrei Bulava
ALT Linux hardware support
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/hardware/0 hardware/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 hardware hardware/ http://lore.altlinux.org/hardware \
hardware@altlinux.ru hardware@lists.altlinux.org hardware@lists.altlinux.ru hardware@lists.altlinux.com hardware@altlinux.org
public-inbox-index hardware
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.hardware
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git