From: "Антон Мидюков" <midyukov-anton@ya.ru>
To: ALT Devel discussion list <devel@lists.altlinux.org>
Subject: Re: [devel] [#216568] FAILED non-identical noarch packages
Date: Sat, 24 Nov 2018 18:49:37 +0700
Message-ID: <871e4e89-21bd-dccf-433b-a51d20b3f352@ya.ru> (raw)
In-Reply-To: <20181124110106.GA13112@gyle.altlinux.org>
Здравствуйте.
Почему пакеты получаются не идентичными? В них одни и те же файлы - 3d
модели.
Неужели потому, что i586 был собран со второй попытки. Первый раз для
i586 kicad-packages3D случился:
hasher-priv: master: idle time limit (3600 seconds) exceeded
Как с этим быть?
24.11.2018 18:01, Girar Builder awaiter robot пишет:
> http://git.altlinux.org/tasks/216568/logs/events.4.1.log
>
> 2018-Nov-24 08:46:50 :: test-only task #216568 for sisyphus resumed by antohami:
> #100 build 5.0.1-alt1 from /people/antohami/packages/kicad-doc.git fetched at 2018-Nov-18 14:00:13
> #200 build 5.0.1-alt1 from /people/antohami/packages/kicad-i18n.git fetched at 2018-Nov-18 14:02:03
> #300 build 5.0.1-alt1 from /people/antohami/packages/kicad-symbols.git fetched at 2018-Nov-18 15:05:11
> #400 build 5.0.1-alt1 from /people/antohami/packages/kicad-footprints.git fetched at 2018-Nov-18 15:07:30
> #500 build 5.0.1-alt1 from /people/antohami/packages/kicad-templates.git fetched at 2018-Nov-18 15:10:09
> #600 build 5.0.1-alt1 from /people/antohami/packages/kicad-packages3D.git fetched at 2018-Nov-22 07:07:04
> #700 removed
> #1000 removed
> #1100 build 5.0.1-alt1 from /people/antohami/packages/kicad.git fetched at 2018-Nov-23 09:09:05
> 2018-Nov-24 08:50:45 :: created build repo
> 2018-Nov-24 08:50:47 :: [aarch64] #100 kicad-doc.git 5.0.1-alt1: build start
> 2018-Nov-24 08:50:47 :: [x86_64] #100 kicad-doc.git 5.0.1-alt1: build start
> 2018-Nov-24 08:50:47 :: [i586] #100 kicad-doc.git 5.0.1-alt1: build start
> 2018-Nov-24 08:51:34 :: [i586] kicad-doc.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:51:34 :: [x86_64] kicad-doc.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:51:34 :: [i586] #100 kicad-doc.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:51:34 :: [i586] #200 kicad-i18n.git 5.0.1-alt1: build start
> 2018-Nov-24 08:51:34 :: [x86_64] #100 kicad-doc.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:51:34 :: [x86_64] #200 kicad-i18n.git 5.0.1-alt1: build start
> 2018-Nov-24 08:51:55 :: [i586] kicad-i18n.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:51:55 :: [i586] #200 kicad-i18n.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:51:55 :: [i586] #300 kicad-symbols.git 5.0.1-alt1: build start
> 2018-Nov-24 08:51:55 :: [x86_64] kicad-i18n.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:51:55 :: [x86_64] #200 kicad-i18n.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:51:55 :: [x86_64] #300 kicad-symbols.git 5.0.1-alt1: build start
> 2018-Nov-24 08:52:15 :: [i586] kicad-symbols.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:52:15 :: [i586] #300 kicad-symbols.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:52:15 :: [i586] #400 kicad-footprints.git 5.0.1-alt1: build start
> 2018-Nov-24 08:52:15 :: [x86_64] kicad-symbols.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:52:15 :: [x86_64] #300 kicad-symbols.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:52:15 :: [x86_64] #400 kicad-footprints.git 5.0.1-alt1: build start
> 2018-Nov-24 08:52:19 :: [aarch64] kicad-doc.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:52:19 :: [aarch64] #100 kicad-doc.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:52:19 :: [aarch64] #200 kicad-i18n.git 5.0.1-alt1: build start
> 2018-Nov-24 08:52:35 :: [i586] kicad-footprints.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:52:35 :: [i586] #400 kicad-footprints.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:52:35 :: [i586] #500 kicad-templates.git 5.0.1-alt1: build start
> 2018-Nov-24 08:52:36 :: [x86_64] kicad-footprints.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:52:37 :: [x86_64] #400 kicad-footprints.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:52:37 :: [x86_64] #500 kicad-templates.git 5.0.1-alt1: build start
> 2018-Nov-24 08:52:56 :: [i586] kicad-templates.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:52:56 :: [i586] #500 kicad-templates.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:52:56 :: [i586] #600 kicad-packages3D.git 5.0.1-alt1: build start
> 2018-Nov-24 08:52:59 :: [x86_64] kicad-templates.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:52:59 :: [x86_64] #500 kicad-templates.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:52:59 :: [x86_64] #600 kicad-packages3D.git 5.0.1-alt1: build start
> 2018-Nov-24 08:53:13 :: [aarch64] kicad-i18n.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:53:13 :: [aarch64] #200 kicad-i18n.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:53:13 :: [aarch64] #300 kicad-symbols.git 5.0.1-alt1: build start
> 2018-Nov-24 08:54:08 :: [aarch64] kicad-symbols.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:54:08 :: [aarch64] #300 kicad-symbols.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:54:08 :: [aarch64] #400 kicad-footprints.git 5.0.1-alt1: build start
> 2018-Nov-24 08:54:21 :: [x86_64] kicad-packages3D.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:54:21 :: [x86_64] #600 kicad-packages3D.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:54:21 :: [x86_64] #1100 kicad.git 5.0.1-alt1: build start
> 2018-Nov-24 08:55:01 :: [aarch64] kicad-footprints.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:55:01 :: [aarch64] #400 kicad-footprints.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:55:01 :: [aarch64] #500 kicad-templates.git 5.0.1-alt1: build start
> 2018-Nov-24 08:55:56 :: [aarch64] kicad-templates.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:55:56 :: [aarch64] #500 kicad-templates.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:55:56 :: [aarch64] #600 kicad-packages3D.git 5.0.1-alt1: build start
> 2018-Nov-24 08:57:35 :: [aarch64] kicad-packages3D.git 5.0.1-alt1: remote: no need to rebuild
> 2018-Nov-24 08:57:35 :: [aarch64] #600 kicad-packages3D.git 5.0.1-alt1: build OK
> 2018-Nov-24 08:57:35 :: [aarch64] #1100 kicad.git 5.0.1-alt1: build start
> 2018-Nov-24 09:33:07 :: [x86_64] #1100 kicad.git 5.0.1-alt1: build OK
> 2018-Nov-24 10:10:03 :: [i586] #600 kicad-packages3D.git 5.0.1-alt1: build OK
> 2018-Nov-24 10:10:03 :: [i586] #1100 kicad.git 5.0.1-alt1: build start
> 2018-Nov-24 10:20:04 :: [aarch64] #1100 kicad.git 5.0.1-alt1: build OK
> 2018-Nov-24 10:47:40 :: [i586] #1100 kicad.git 5.0.1-alt1: build OK
> 2018-Nov-24 10:50:25 :: build check OK
> --- kicad-packages3D-5.0.1-alt1.noarch.rpm.x86_64 2018-11-24 10:51:57.225545652 +0000
> +++ kicad-packages3D-5.0.1-alt1.noarch.rpm.i586 2018-11-24 10:51:57.234545713 +0000
> @@ -1,3 +1,3 @@
> -Requires: .sisyphus.216568.600.3.1-kicad-packages3D-part1-5.0.1-alt1
> -Requires: .sisyphus.216568.600.3.1-kicad-packages3D-part2-5.0.1-alt1
> +Requires: .sisyphus.216568.600.4.1-kicad-packages3D-part1-5.0.1-alt1
> +Requires: .sisyphus.216568.600.4.1-kicad-packages3D-part2-5.0.1-alt1
> Requires: rpmlib(PayloadIsLzma)
> error (#600): non-identical noarch packages
> --- kicad-packages3D-part1-5.0.1-alt1.noarch.rpm.x86_64 2018-11-24 10:52:40.959840009 +0000
> +++ kicad-packages3D-part1-5.0.1-alt1.noarch.rpm.i586 2018-11-24 10:53:24.910135819 +0000
> @@ -6768,3 +6768,3 @@
> Requires: rpmlib(PayloadIsLzma)
> -Provides: .sisyphus.216568.600.3.1-kicad-packages3D-part1-5.0.1-alt1
> +Provides: .sisyphus.216568.600.4.1-kicad-packages3D-part1-5.0.1-alt1
> Provides: kicad-packages3D-part1 = 5.0.1-alt1
> error (#600): non-identical noarch packages
> --- kicad-packages3D-part2-5.0.1-alt1.noarch.rpm.x86_64 2018-11-24 10:53:34.386199597 +0000
> +++ kicad-packages3D-part2-5.0.1-alt1.noarch.rpm.i586 2018-11-24 10:53:43.435260502 +0000
> @@ -2832,3 +2832,3 @@
> Requires: rpmlib(PayloadIsLzma)
> -Provides: .sisyphus.216568.600.3.1-kicad-packages3D-part2-5.0.1-alt1
> +Provides: .sisyphus.216568.600.4.1-kicad-packages3D-part2-5.0.1-alt1
> Provides: kicad-packages3D-part2 = 5.0.1-alt1
> error (#600): non-identical noarch packages
> --- kicad-packages3D-5.0.1-alt1.noarch.rpm.i586 2018-11-24 10:55:29.307973086 +0000
> +++ kicad-packages3D-5.0.1-alt1.noarch.rpm.aarch64 2018-11-24 10:55:29.315973139 +0000
> @@ -1,3 +1,3 @@
> -Requires: .sisyphus.216568.600.4.1-kicad-packages3D-part1-5.0.1-alt1
> -Requires: .sisyphus.216568.600.4.1-kicad-packages3D-part2-5.0.1-alt1
> +Requires: .sisyphus.216568.600.3.1-kicad-packages3D-part1-5.0.1-alt1
> +Requires: .sisyphus.216568.600.3.1-kicad-packages3D-part2-5.0.1-alt1
> Requires: rpmlib(PayloadIsLzma)
> error (#600): non-identical noarch packages
> --- kicad-packages3D-part1-5.0.1-alt1.noarch.rpm.i586 2018-11-24 10:56:12.430263322 +0000
> +++ kicad-packages3D-part1-5.0.1-alt1.noarch.rpm.aarch64 2018-11-24 10:56:55.606553923 +0000
> @@ -6768,3 +6768,3 @@
> Requires: rpmlib(PayloadIsLzma)
> -Provides: .sisyphus.216568.600.4.1-kicad-packages3D-part1-5.0.1-alt1
> +Provides: .sisyphus.216568.600.3.1-kicad-packages3D-part1-5.0.1-alt1
> Provides: kicad-packages3D-part1 = 5.0.1-alt1
> error (#600): non-identical noarch packages
> --- kicad-packages3D-part2-5.0.1-alt1.noarch.rpm.i586 2018-11-24 10:57:04.585614356 +0000
> +++ kicad-packages3D-part2-5.0.1-alt1.noarch.rpm.aarch64 2018-11-24 10:57:13.682675585 +0000
> @@ -2832,3 +2832,3 @@
> Requires: rpmlib(PayloadIsLzma)
> -Provides: .sisyphus.216568.600.4.1-kicad-packages3D-part2-5.0.1-alt1
> +Provides: .sisyphus.216568.600.3.1-kicad-packages3D-part2-5.0.1-alt1
> Provides: kicad-packages3D-part2 = 5.0.1-alt1
> error (#600): non-identical noarch packages
> 2018-Nov-24 11:01:05 :: noarch check FAILED
> 2018-Nov-24 11:01:05 :: task #216568 for sisyphus FAILED
--
С уважением, Антон Мидюков <antohami@altlinux.org>
next parent reply other threads:[~2018-11-24 11:49 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-24 11:49 ` Антон Мидюков [this message]
2018-11-27 4:33 ` Антон Мидюков
2018-11-27 6:01 ` Ivan A. Melnikov
2018-11-27 13:11 ` Антон Мидюков
2018-11-27 14:26 ` Vladimir D. Seleznev
2018-11-28 3:47 ` Alexey V. Vissarionov
2018-12-03 17:52 ` Vladimir D. Seleznev
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=871e4e89-21bd-dccf-433b-a51d20b3f352@ya.ru \
--to=midyukov-anton@ya.ru \
--cc=devel@lists.altlinux.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
ALT Linux Team development discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/devel/0 devel/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 devel devel/ http://lore.altlinux.org/devel \
devel@altlinux.org devel@altlinux.ru devel@lists.altlinux.org devel@lists.altlinux.ru devel@linux.iplabs.ru mandrake-russian@linuxteam.iplabs.ru sisyphus@linuxteam.iplabs.ru
public-inbox-index devel
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.devel
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git