On Tue, Sep 22, 2026 at 01:18:09PM +0400, Daniil Gnusarev wrote:
> This enables the PCIe controller on Repka Pi5 board.
> It also resolves the shutdown/reboot issue. Without this,
> the `mmu600_pcie` node (which is unused but starts automatically)
> fails to shut down, causing the shutdown process to hang.
> 
> Based on the original dts:
> Link: https://gitflic.ru/project/npo_rbs/repka-os_linux-rockchip/blob?file=arch/arm64/boot/dts/rockchip/rk3588-repka-pi5.dts&branch=master

Лучше указывать ссылку на конкретный коммит, например

https://gitflic.ru/project/npo_rbs/repka-os_linux-rockchip/blob?file=arch/arm64/boot/dts/rockchip/rk3588-repka-pi5.dts&commit=4b64c5c7f6b1747e280e3d5b884717aea3f15c17

> Signed-off-by: Daniil Gnusarev <gnusarevda@basealt.ru>
> ---
>  .../boot/dts/rockchip/rk3588-repka-pi5.dts    | 27 +++++++++++++++++++
>  1 file changed, 27 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588-repka-pi5.dts b/arch/arm64/boot/dts/rockchip/rk3588-repka-pi5.dts
> index 4e4207108dbf2..1ff882188f4d4 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3588-repka-pi5.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3588-repka-pi5.dts
> @@ -74,6 +74,17 @@ fan: pwm-fan {
>  		#cooling-cells = <2>;
>  	};
>  
> +	vcc3v3_pcie30: vcc3v3-pcie30 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc3v3_pcie30";
> +		startup-delay-us = <5000>;
> +		enable-active-high;
> +		gpios = <&gpio2 RK_PB6 GPIO_ACTIVE_HIGH>;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc5v0_sys>;
> +	};
> +
>  	vcc5v0_sys: regulator-vcc5v0-sys {
>  		compatible = "regulator-fixed";
>  		regulator-name = "vcc5v0_sys";
> @@ -260,6 +271,22 @@ map1 {
>  	};
>  };
>  
> +&pcie30phy {
> +	data-lanes = <1 3 2 4>;
> +	clocks = <&cru PCLK_PCIE_COMBO_PIPE_PHY>,
> +		 <&cru PCLK_PHP_ROOT>;
> +	clock-names = "pclk", "pipe";
> +	status = "okay";
> +};
> +
> +&pcie3x4 {
> +	num-lanes = <1>;
> +	max-link-speed = <3>;
> +	vpcie3v3-supply = <&vcc3v3_pcie30>;
> +	reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
> +	status = "okay";
> +};
> +
>  &pinctrl {
>  	fan {
>  		fan_tach: fan-tach {
> -- 
> 2.42.2

Reviewed-by: Ivan A. Melnikov <iv@altlinux.org>

-- 
  wbr,
    iv m.