* [d-kernel] 2xP233MMX + std-smp = trouble
@ 2004-06-15 16:53 Michael Shigorin
2004-06-15 19:29 ` Sergey Vlasov
2004-07-07 15:02 ` Sergey Vlasov
0 siblings, 2 replies; 6+ messages in thread
From: Michael Shigorin @ 2004-06-15 16:53 UTC (permalink / raw)
To: devel-kernel
[-- Attachment #1.1: Type: text/plain, Size: 1314 bytes --]
Здравствуйте.
Имеется dual Socket7 материнская плата Soyo на 440HX с двумя
iP233MMX. Проблема в том, что пока не удалось загрузить на ней
ни одно из *smp*alt-ядер, которые проверялись (*) -- сразу после
"Ok, booting the kernel.\n" мертвый вис.
К сожалению, я смутно помню объяснения vsu@ чуть более месячной
давности по поводу схожего на вид зависания vs-smp на KT133A и, в
частности, не помню, что может быть причиной и куда смотреть/
что рассказывать. Посему прилагаю dmesg с загрузившегося ядра
из Compact 2.3 (с noapic nolapic -- иначе странно глючат сетевые,
причем обе -- и выгрызенное из лога инсталятора, где оно не
выключалось).
PS: diff -u /boot/config* для 2.4.22-std-{up,smp}-alt17 не
показал ничего похожего на знакомые подозрительные места
(например, CONFIG_M686) -- правда, рассказал много страшных
незнакомых слов. :-)
PPS: на этой машинке можно будет оттестировать необходимые
аспекты bootloader-utils, инсталятора и всего прочего, чтобы
установка на SMP не была сломана (как вышло в Compact 2.3).
* проверялись ядра:
+ kernel-image-std-up-2.4.22-alt17
- kernel-image-std26-smp-2.6.6-alt5
- kernel-image-std-smp-2.4.26-alt3
- kernel-image-std-smp-2.4.22-alt17
--
---- WBR, Michael Shigorin <mike@altlinux.ru>
------ Linux.Kiev http://www.linux.kiev.ua/
[-- Attachment #1.2: dmesg-dual-noapic --]
[-- Type: text/plain, Size: 4963 bytes --]
Linux version 2.4.22-std-up-alt17 (builder@mash.office.altlinux.ru) (gcc version 2.96 20000731 (ALT Linux, build 2.96-alt6)) #1 Wed Feb 4 22:52:03 MSK 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000008000000 (usable)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
128MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
found SMP MP-table at 000f0d20
hm, page 000f0000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f0000 reserved twice.
hm, page 000f1000 reserved twice.
On node 0 totalpages: 32768
zone(0): 4096 pages.
zone(1): 28672 pages.
zone(2): 0 pages.
DMI not present.
ACPI: Unable to locate RSDP
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) APIC version 17
Processor #1 Pentium(tm) APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Kernel command line: BOOT_IMAGE=linux-up ro root=305 noapic nolapic
Initializing CPU#0
Detected 232.531 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 463.66 BogoMIPS
Memory: 126904k/131072k available (1193k kernel code, 3780k reserved, 502k data, 132k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
Intel Pentium with F0 0F bug - workaround enabled.
CPU: After generic, caps: 008003bf 00000000 00000000 00000000
CPU: Common caps: 008003bf 00000000 00000000 00000000
CPU: Intel Pentium MMX stepping 03
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
BIOS bug, local APIC #0 not detected!...
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: none
ACPI: Subsystem revision 20040116
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfb490, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
Limiting direct PCI/PCI transfers.
Activating ISA DMA hang workarounds.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX3: IDE controller at PCI slot 00:07.1
PIIX3: chipset revision 0
PIIX3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: IBM-DTLA-307030, ATA DISK drive
blk: queue c02f8860, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=3737/255/63, (U)DMA
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 >
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 99k freed
VFS: Mounted root (romfs filesystem) readonly.
Journalled Block Device driver loaded
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 132k freed
Executing init=/sbin/init
Adding Swap: 265064k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
Real Time Clock Driver v1.10e
[-- Attachment #1.3: dmesg-dual-apic --]
[-- Type: text/plain, Size: 9714 bytes --]
<4>Linux version 2.4.22-std-up-alt17 (builder@mash.office.altlinux.ru) (gcc version 2.96 20000731 (ALT Linux, build 2.96-alt6)) #1 Wed Feb 4 22:52:03 MSK 2004
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 0000000008000000 (usable)
<4> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
<4> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
<4> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
<5>0MB HIGHMEM available.
<5>128MB LOWMEM available.
<7>ACPI: have wakeup address 0xc0001000
<4>found SMP MP-table at 000f0d20
<4>hm, page 000f0000 reserved twice.
<4>hm, page 000f1000 reserved twice.
<4>hm, page 000f0000 reserved twice.
<4>hm, page 000f1000 reserved twice.
<4>On node 0 totalpages: 32768
<4>zone(0): 4096 pages.
<4>zone(1): 28672 pages.
<4>zone(2): 0 pages.
<6>DMI not present.
<3>ACPI: Unable to locate RSDP
<4>Intel MultiProcessor Specification v1.1
<4> Virtual Wire compatibility mode.
<4>OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
<4>Processor #0 Pentium(tm) APIC version 17
<4>Processor #1 Pentium(tm) APIC version 17
<4>I/O APIC #2 Version 17 at 0xFEC00000.
<4>Enabling APIC mode: Flat. Using 1 I/O APICs
<4>Processors: 2
<4>Kernel command line: ramdisk_size=54000 initrd=initrd.rdz root=/dev/ram3 fexpert expert design=Compact BOOT_IMAGE=vmlinuz altcode=,1207120020,5C91F0CC,
<6>Initializing CPU#0
<4>Detected 232.531 MHz processor.
<4>Console: colour VGA+ 80x25
<4>Calibrating delay loop... 463.66 BogoMIPS
<6>Memory: 126200k/131072k available (1193k kernel code, 4484k reserved, 502k data, 132k init, 0k highmem)
<6>Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
<6>Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<6>Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
<4>Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
<5>Intel Pentium with F0 0F bug - workaround enabled.
<7>CPU: After generic, caps: 008003bf 00000000 00000000 00000000
<7>CPU: Common caps: 008003bf 00000000 00000000 00000000
<4>CPU: Intel Pentium MMX stepping 03
<6>Checking 'hlt' instruction... OK.
<4>POSIX conformance testing by UNIFIX
<4>enabled ExtINT on CPU#0
<4>ESR value before enabling vector: 00000000
<4>ESR value after enabling vector: 00000000
<4>ENABLING IO-APIC IRQs
<4>Setting 2 in the phys_id_present_map
<6>...changing IO-APIC physical APIC ID to 2 ... ok.
<7>init IO_APIC IRQs
<7> IO-APIC (apicid-pin) 2-0, 2-20, 2-21, 2-22, 2-23 not connected.
<6>..TIMER: vector=0x31 pin1=2 pin2=0
<3>..MP-BIOS bug: 8254 timer not connected to IO-APIC
<6>...trying to set up timer (IRQ0) through the 8259A ...
<4>..... (found pin 0) ...works.
<7>number of MP IRQ sources: 21.
<7>number of IO-APIC #2 registers: 24.
<6>testing the IO APIC.......................
<4>
<7>IO APIC #2......
<7>.... register #00: 02000000
<7>....... : physical APIC id: 02
<7>....... : Delivery Type: 0
<7>....... : LTS : 0
<7>.... register #01: 00170011
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 0
<7>....... : IO APIC version: 0011
<7>.... register #02: 00000000
<7>....... : arbitration: 00
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 001 01 0 0 0 0 0 1 1 31
<7> 01 001 01 0 0 0 0 0 1 1 39
<7> 02 000 00 1 0 0 0 0 0 0 00
<7> 03 001 01 0 0 0 0 0 1 1 41
<7> 04 001 01 0 0 0 0 0 1 1 49
<7> 05 001 01 0 0 0 0 0 1 1 51
<7> 06 001 01 0 0 0 0 0 1 1 59
<7> 07 001 01 0 0 0 0 0 1 1 61
<7> 08 001 01 0 0 0 0 0 1 1 69
<7> 09 001 01 0 0 0 0 0 1 1 71
<7> 0a 001 01 0 0 0 0 0 1 1 79
<7> 0b 001 01 0 0 0 0 0 1 1 81
<7> 0c 001 01 0 0 0 0 0 1 1 89
<7> 0d 001 01 0 0 0 0 0 1 1 91
<7> 0e 001 01 0 0 0 0 0 1 1 99
<7> 0f 001 01 0 0 0 0 0 1 1 A1
<7> 10 001 01 1 1 0 1 0 1 1 A9
<7> 11 001 01 1 1 0 1 0 1 1 B1
<7> 12 001 01 1 1 0 1 0 1 1 B9
<7> 13 001 01 1 1 0 1 0 1 1 C1
<7> 14 000 00 1 0 0 0 0 0 0 00
<7> 15 000 00 1 0 0 0 0 0 0 00
<7> 16 000 00 1 0 0 0 0 0 0 00
<7> 17 000 00 1 0 0 0 0 0 0 00
<7>IRQ to pin mappings:
<7>IRQ0 -> 0:0
<7>IRQ1 -> 0:1
<7>IRQ3 -> 0:3
<7>IRQ4 -> 0:4
<7>IRQ5 -> 0:5
<7>IRQ6 -> 0:6
<7>IRQ7 -> 0:7
<7>IRQ8 -> 0:8
<7>IRQ9 -> 0:9
<7>IRQ10 -> 0:10
<7>IRQ11 -> 0:11
<7>IRQ12 -> 0:12
<7>IRQ13 -> 0:13
<7>IRQ14 -> 0:14
<7>IRQ15 -> 0:15
<7>IRQ16 -> 0:16
<7>IRQ17 -> 0:17
<7>IRQ18 -> 0:18
<7>IRQ19 -> 0:19
<6>.................................... done.
<4>Using local APIC timer interrupts.
<4>calibrating APIC timer ...
<4>..... CPU clock speed is 232.5279 MHz.
<4>..... host bus clock speed is 66.4364 MHz.
<4>cpu: 0, clocks: 664364, slice: 332182
<4>CPU0<T0:664352,T1:332160,D:10,S:332182,C:664364>
<4>mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
<4>mtrr: detected mtrr type: none
<6>ACPI: Subsystem revision 20040116
<6>ACPI: Interpreter disabled.
<6>PCI: PCI BIOS revision 2.10 entry at 0xfb490, last bus=0
<6>PCI: Using configuration type 1
<6>PCI: Probing PCI hardware
<4>PCI: ACPI tables contain no PCI IRQ routing entries
<4>PCI: Probing PCI hardware (bus 00)
<4>PCI BIOS passed nonexistent PCI bus 0!
<4>PCI BIOS passed nonexistent PCI bus 0!
<4>PCI BIOS passed nonexistent PCI bus 0!
<4>PCI BIOS passed nonexistent PCI bus 0!
<6>Limiting direct PCI/PCI transfers.
<6>Activating ISA DMA hang workarounds.
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<4>Starting kswapd
<5>VFS: Disk quotas vdquot_6.5.1
<4>pty: 256 Unix98 ptys configured
<6>Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>ttyS01 at 0x02f8 (irq = 3) is a 16550A
<6>NET4: Frame Diverter 0.46
<4>RAMDISK driver initialized: 16 RAM disks of 54000K size 1024 blocksize
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>PIIX3: IDE controller at PCI slot 00:07.1
<6>PIIX3: chipset revision 0
<6>PIIX3: not 100% native mode: will probe irqs later
<6> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
<6> ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
<4>hda: IBM-DTLA-307030, ATA DISK drive
<4>blk: queue c02f8860, I/O limit 4095Mb (mask 0xffffffff)
<4>hdc: CD-540E, ATAPI CD/DVD-ROM drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>ide1 at 0x170-0x177,0x376 on irq 15
<4>hda: attached ide-disk driver.
<4>hda: host protected area => 1
<6>hda: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=3737/255/63, (U)DMA
<6>Partition check:
<6> hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 >
<6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP
<6>IP: routing cache hash table of 1024 buckets, 8Kbytes
<6>TCP: Hash tables configured (established 8192 bind 16384)
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<5>RAMDISK: Compressed image found at block 0
<6>Freeing initrd memory: 801k freed
<4>VFS: Mounted root (ext2 filesystem).
<4>hdc: attached ide-cdrom driver.
<6>hdc: ATAPI 40X CD-ROM drive, 128kB Cache, (U)DMA
<6>Uniform CD-ROM driver Revision: 3.12
<6>SCSI subsystem driver Revision: 1.00
<3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
<7>ISO 9660 Extensions: Microsoft Joliet Level 3
<3>kmod: failed to exec /sbin/modprobe -s -k nls_iso8859-1, errno = 2
<3>kmod: failed to exec /sbin/modprobe -s -k nls_koi8-r, errno = 2
<7>ISO 9660 Extensions: RRIP_1991A
<6>usb.c: registered new driver usbdevfs
<6>usb.c: registered new driver hub
<6>usb-uhci.c: $Revision: 1.275 $ time 23:06:28 Feb 4 2004
<6>usb-uhci.c: High bandwidth mode enabled
<6>usb-uhci.c: USB UHCI at I/O 0x6000, IRQ 11
<4>usb-uhci.c: Detected 2 ports
<6>usb.c: new USB bus registered, assigned bus number 1
<6>hub.c: USB hub found
<6>hub.c: 2 ports detected
<6>usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
<3>kmod: failed to exec /sbin/modprobe -s -k parport_lowlevel, errno = 2
<4>imm: Version 2.05 (for Linux 2.4.0)
<4>imm: parport reports no devices.
<3>kmod: failed to exec /sbin/modprobe -s -k parport_lowlevel, errno = 2
<4>ppa: Version 2.07 (for Linux 2.4.x)
<4>ppa: parport reports no devices.
<6>inserting floppy driver for 2.4.22-std-up-alt17
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<6>Journalled Block Device driver loaded
<6>Adding Swap: 265064k swap-space (priority -1)
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<4>EXT2-fs warning (device ide0(3,5)): ext2_read_super: mounting ext3 filesystem as ext2
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [d-kernel] 2xP233MMX + std-smp = trouble
2004-06-15 16:53 [d-kernel] 2xP233MMX + std-smp = trouble Michael Shigorin
@ 2004-06-15 19:29 ` Sergey Vlasov
2004-06-16 6:35 ` Michael Shigorin
2004-06-16 8:55 ` Michael Shigorin
2004-07-07 15:02 ` Sergey Vlasov
1 sibling, 2 replies; 6+ messages in thread
From: Sergey Vlasov @ 2004-06-15 19:29 UTC (permalink / raw)
To: devel-kernel
[-- Attachment #1: Type: text/plain, Size: 505 bytes --]
On Tue, Jun 15, 2004 at 07:53:43PM +0300, Michael Shigorin wrote:
> Имеется dual Socket7 материнская плата Soyo на 440HX с двумя
> iP233MMX. Проблема в том, что пока не удалось загрузить на ней
> ни одно из *smp*alt-ядер, которые проверялись (*) -- сразу после
> "Ok, booting the kernel.\n" мертвый вис.
Проверялось, я надеюсь, с vga=normal ?
Стоит ещё попробовать забрать с
http://people.redhat.com/zaitcev/linux/ программу под названием
mptable и посмотреть, что выдаёт mptable -verbose .
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [d-kernel] 2xP233MMX + std-smp = trouble
2004-06-15 19:29 ` Sergey Vlasov
@ 2004-06-16 6:35 ` Michael Shigorin
2004-06-16 8:55 ` Michael Shigorin
1 sibling, 0 replies; 6+ messages in thread
From: Michael Shigorin @ 2004-06-16 6:35 UTC (permalink / raw)
To: devel-kernel
[-- Attachment #1: Type: text/plain, Size: 673 bytes --]
On Tue, Jun 15, 2004 at 11:29:47PM +0400, Sergey Vlasov wrote:
> > Имеется dual Socket7 материнская плата Soyo на 440HX с двумя
> > iP233MMX. Проблема в том, что пока не удалось загрузить на ней
> > ни одно из *smp*alt-ядер, которые проверялись (*) -- сразу после
> > "Ok, booting the kernel.\n" мертвый вис.
> Проверялось, я надеюсь, с vga=normal ?
Угу.
> Стоит ещё попробовать забрать с
> http://people.redhat.com/zaitcev/linux/ программу под названием
> mptable и посмотреть, что выдаёт mptable -verbose .
Чичас доберусь до конторы и гляну, спасибо.
--
---- WBR, Michael Shigorin <mike@altlinux.ru>
------ Linux.Kiev http://www.linux.kiev.ua/
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [d-kernel] 2xP233MMX + std-smp = trouble
2004-06-15 19:29 ` Sergey Vlasov
2004-06-16 6:35 ` Michael Shigorin
@ 2004-06-16 8:55 ` Michael Shigorin
1 sibling, 0 replies; 6+ messages in thread
From: Michael Shigorin @ 2004-06-16 8:55 UTC (permalink / raw)
To: devel-kernel
[-- Attachment #1.1: Type: text/plain, Size: 209 bytes --]
On Tue, Jun 15, 2004 at 11:29:47PM +0400, Sergey Vlasov wrote:
> что выдаёт mptable -verbose
attached
--
---- WBR, Michael Shigorin <mike@altlinux.ru>
------ Linux.Kiev http://www.linux.kiev.ua/
[-- Attachment #1.2: mptable.txt --]
[-- Type: text/plain, Size: 2897 bytes --]
===============================================================================
MPTable, version 2.0.15 Linux
looking for EBDA pointer @ 0x040e, NOT found
searching CMOS 'top of mem' @ 0x0009fc00 (639K)
searching BIOS @ 0x000f0000
MP FPS found in BIOS @ physical addr: 0x000f0d20
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000f0d20
signature: '_MP_'
length: 16 bytes
version: 1.1
checksum: 0x53
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x0xf0d34
signature: 'PCMP'
base table length: 292
version: 1.1
checksum: 0xd5
OEM ID: 'OEM00000'
Product ID: 'PROD00000000'
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 28
local APIC address: 0xfee00000
extended table length: 0
extended table checksum: 0
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
0 0x11 BSP, usable 5 2 1 0x07bf
1 0x11 AP, usable 5 2 1 0x07bf
--
Bus: Bus ID Type
0 ISA
1 PCI
--
I/O APICs: APIC ID Version State Address
2 0x11 usable 0xfec00000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT conforms conforms 0 0 2 0
INT conforms conforms 0 1 2 1
INT conforms conforms 0 0 2 2
INT conforms conforms 0 3 2 3
INT conforms conforms 0 4 2 4
INT conforms conforms 0 5 2 5
INT conforms conforms 0 6 2 6
INT conforms conforms 0 7 2 7
INT conforms conforms 0 8 2 8
INT conforms conforms 0 9 2 9
INT conforms conforms 0 10 2 10
INT conforms conforms 0 11 2 11
INT conforms conforms 0 12 2 12
INT conforms conforms 0 13 2 13
INT conforms conforms 0 14 2 14
INT conforms conforms 0 15 2 15
INT active-lo level 1 14:A 2 16
INT active-lo level 1 15:A 2 17
INT active-lo level 1 16:A 2 18
INT active-lo level 1 17:A 2 19
SMI conforms conforms 0 0 2 23
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT active-hi edge 0 0 255 0
NMI active-hi edge 0 0 255 1
===============================================================================
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [d-kernel] 2xP233MMX + std-smp = trouble
2004-06-15 16:53 [d-kernel] 2xP233MMX + std-smp = trouble Michael Shigorin
2004-06-15 19:29 ` Sergey Vlasov
@ 2004-07-07 15:02 ` Sergey Vlasov
2004-07-07 15:23 ` [Hardware] " Michael Shigorin
1 sibling, 1 reply; 6+ messages in thread
From: Sergey Vlasov @ 2004-07-07 15:02 UTC (permalink / raw)
To: devel-kernel; +Cc: hardware
[-- Attachment #1: Type: text/plain, Size: 901 bytes --]
On Tue, Jun 15, 2004 at 07:53:43PM +0300, Michael Shigorin wrote:
> Имеется dual Socket7 материнская плата Soyo на 440HX с двумя
> iP233MMX. Проблема в том, что пока не удалось загрузить на ней
> ни одно из *smp*alt-ядер, которые проверялись (*) -- сразу после
> "Ok, booting the kernel.\n" мертвый вис.
>
[skip]
> Intel Pentium with F0 0F bug - workaround enabled.
> CPU: After generic, caps: 008003bf 00000000 00000000 00000000
> CPU: Common caps: 008003bf 00000000 00000000 00000000
> CPU: Intel Pentium MMX stepping 03
С такими процессорами ядра std-smp действительно не запустятся.
Дело в том, что std-smp собирается с опцией CONFIG_HIGHMEM64G=y для
поддержки более чем 4 GB RAM; для этого используется режим Physical
Address Extension (PAE), появившийся начиная с Pentium Pro. Однако
собранное с такими параметрами ядро не работает с процессорами, не
имеющими поддержки PAE.
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Hardware] Re: [d-kernel] 2xP233MMX + std-smp = trouble
2004-07-07 15:02 ` Sergey Vlasov
@ 2004-07-07 15:23 ` Michael Shigorin
0 siblings, 0 replies; 6+ messages in thread
From: Michael Shigorin @ 2004-07-07 15:23 UTC (permalink / raw)
To: devel-kernel, hardware
[-- Attachment #1: Type: text/plain, Size: 712 bytes --]
On Wed, Jul 07, 2004 at 07:02:58PM +0400, Sergey Vlasov wrote:
> > CPU: Intel Pentium MMX stepping 03
> С такими процессорами ядра std-smp действительно не запустятся.
> Дело в том, что std-smp собирается с опцией CONFIG_HIGHMEM64G=y
Спасибо :-)
> для поддержки более чем 4 GB RAM; для этого используется режим
> Physical Address Extension (PAE), появившийся начиная с Pentium
> Pro. Однако собранное с такими параметрами ядро не работает с
> процессорами, не имеющими поддержки PAE.
Может, тогда уже и собирать его как i686 и соотв. для PPro+?
Терять нечего, а приобрести немного получится.
--
---- WBR, Michael Shigorin <mike@altlinux.ru>
------ Linux.Kiev http://www.linux.kiev.ua/
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2004-07-07 15:23 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2004-06-15 16:53 [d-kernel] 2xP233MMX + std-smp = trouble Michael Shigorin
2004-06-15 19:29 ` Sergey Vlasov
2004-06-16 6:35 ` Michael Shigorin
2004-06-16 8:55 ` Michael Shigorin
2004-07-07 15:02 ` Sergey Vlasov
2004-07-07 15:23 ` [Hardware] " Michael Shigorin
ALT Linux kernel packages development
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/devel-kernel/0 devel-kernel/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 devel-kernel devel-kernel/ http://lore.altlinux.org/devel-kernel \
devel-kernel@altlinux.org devel-kernel@altlinux.ru devel-kernel@altlinux.com
public-inbox-index devel-kernel
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.devel-kernel
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git