* [Comm] модем ADSL
@ 2008-04-05 3:33 Геннадий Ищенко
2008-04-05 6:08 ` Motsyo Gennadi aka Drool
2008-04-07 8:45 ` Sergey
0 siblings, 2 replies; 4+ messages in thread
From: Геннадий Ищенко @ 2008-04-05 3:33 UTC (permalink / raw)
To: community
Нашел пакет документации /usr/share/doc/rp-pppoe-client-3.5, перевел два
документа: README и HOW-TO-CONNECT. Далее по руководству:
#adsl-setup и по пунктам: 1. имя пользователя PPPoE -ввел логин;
2. интерфейс Ethernet для ADSL -eth0;
3. время простоя - 300 сек;
4. адрес основного DNS сервера - 195.161.0.135;
5. адрес альтернат. DNS сервера - 10.253.0.2;
6. отказался от FIREWALL -no;
7. ввел пароль с подтверждением;
8. принял настройки - y.
После #adsl=start в перечне процессов появился: 19708 ? Ss 0:00 /usr/sbin/pppd pty /usr/
sbin/pppoe -p /var/run/pppoe.
В alt Linux Control Center установил флаг на DHCP для eth0 и появившегося сетевого устройства
ppp0 , настройки серверов сейчас не слетают. При попытке соединения, например, с pop.mail.ru
- ошибка соединения. Пингуется только адрес ppp0: 10.112.112.112.
[root@Gena root]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:14:85:50:26:32
inet addr:10.253.111.12 Bcast:10.253.111.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2667 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:192283 (187.7 KiB)
Interrupt:20 Base address:0xe000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1043 errors:0 dropped:0 overruns:0 frame:0
TX packets:1043 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:66332 (64.7 KiB) TX bytes:66332 (64.7 KiB)
ppp0 Link encap:Point-to-Point Protocol
inet addr:10.112.112.112 P-t-P:10.112.112.113 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:40 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:0 (0.0 b) TX bytes:515 (515.0 b)
[root@Gena root]# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.112.112.113 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0
0.0.0.0 10.112.112.113 0.0.0.0 UG 0 0 0 ppp0
Модель модема DSL-500T фирмы D-Link, настройки все как и в Windows XP.
Что еще может быть неправильно?
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [Comm] модем ADSL
2008-04-05 3:33 [Comm] модем ADSL Геннадий Ищенко
@ 2008-04-05 6:08 ` Motsyo Gennadi aka Drool
2008-04-05 6:14 ` Motsyo Gennadi aka Drool
2008-04-07 8:45 ` Sergey
1 sibling, 1 reply; 4+ messages in thread
From: Motsyo Gennadi aka Drool @ 2008-04-05 6:08 UTC (permalink / raw)
To: Геннадий
Ищенко,
ALT Linux Community general discussions
Геннадий Ищенко пишет:
> Нашел пакет документации /usr/share/doc/rp-pppoe-client-3.5, перевел два
> документа: README и HOW-TO-CONNECT. Далее по руководству:
> #adsl-setup и по пунктам: 1. имя пользователя PPPoE -ввел логин;
> 2. интерфейс Ethernet для ADSL -eth0;
> 3. время простоя - 300 сек;
> 4. адрес основного DNS сервера - 195.161.0.135;
> 5. адрес альтернат. DNS сервера - 10.253.0.2;
> 6. отказался от FIREWALL -no;
> 7. ввел пароль с подтверждением;
> 8. принял настройки - y.
> Что еще может быть неправильно?
Неправильная постановка задачи с самого первого вопроса. У Вас модем не
настроен, Вы для соединения используете pppoe - в виндовсе у Вас есть
ярлычек соединения, которое происходит типа как для диалапного дозвона,
только быстро. Ваша же фраза что у Вас "модем настроен" подразумевает
что модем настроен для самостоятельного соединения (режим роутера). В
связи с этим Вам давали советы именно исходя из этого. Реально же -
когда модем настроен роутером и pppoe - это два совершенно разных
метода. У меня был D-link DSL-500T, роутером он настраивается просто
замечательно. Удаляется (если есть) существующее соединение, создается
новое, роутерное, _прямо в модеме_ вводится логин/пароль - и все, он
будет сам соединяться и раздавать интернет. В компьютере (и в линуксе, и
в виндовс) прописывается _только_ IP-адрес модема как шлюз и как
DNS-сервер. Все. Если не справитесь с настройкой модема - в понедельник
могу взять его и наделать пошаговых скриншотов.
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [Comm] модем ADSL
2008-04-05 6:08 ` Motsyo Gennadi aka Drool
@ 2008-04-05 6:14 ` Motsyo Gennadi aka Drool
0 siblings, 0 replies; 4+ messages in thread
From: Motsyo Gennadi aka Drool @ 2008-04-05 6:14 UTC (permalink / raw)
To: ALT Linux Community general discussions
Motsyo Gennadi aka Drool пишет:
>> Что еще может быть неправильно?
>
> Неправильная постановка задачи с самого первого вопроса. У Вас модем не
> настроен, Вы для соединения используете pppoe - в виндовсе у Вас есть
> ярлычек соединения, которое происходит типа как для диалапного дозвона,
> только быстро. Ваша же фраза что у Вас "модем настроен" подразумевает
> что модем настроен для самостоятельного соединения (режим роутера). В
> связи с этим Вам давали советы именно исходя из этого. Реально же -
> когда модем настроен роутером и pppoe - это два совершенно разных
> метода. У меня был D-link DSL-500T, роутером он настраивается просто
> замечательно. Удаляется (если есть) существующее соединение, создается
> новое, роутерное, _прямо в модеме_ вводится логин/пароль - и все, он
> будет сам соединяться и раздавать интернет. В компьютере (и в линуксе, и
> в виндовс) прописывается _только_ IP-адрес модема как шлюз и как
> DNS-сервер. Все. Если не справитесь с настройкой модема - в понедельник
> могу взять его и наделать пошаговых скриншотов.
Первая же ссылка в гугле:
http://www.nsktelecom.ru/articles/id/18/
Там - первый же пункт "Если Вы настраиваете модем в режиме роутера, то
заполняйте следующие поля:". Единственное - либо в виндовс в соединенном
состоянии зайдите любым браузером на адрес модема (192.168.1.1) и
посмотрите чему равны VPI и VCI, либо уточните это у провайдера.
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [Comm] модем ADSL
2008-04-05 3:33 [Comm] модем ADSL Геннадий Ищенко
2008-04-05 6:08 ` Motsyo Gennadi aka Drool
@ 2008-04-07 8:45 ` Sergey
1 sibling, 0 replies; 4+ messages in thread
From: Sergey @ 2008-04-07 8:45 UTC (permalink / raw)
To: ALT Linux Community general discussions
On Saturday 05 April 2008, Геннадий Ищенко wrote:
> Нашел пакет документации /usr/share/doc/rp-pppoe-client-3.5, перевел два
> документа: README и HOW-TO-CONNECT. Далее по руководству:
> #adsl-setup и по пунктам: 1. имя пользователя PPPoE -ввел логин;
Беда только в том, что в этой документации не написано "исключая
модели с Ethernet". Оно им совсем не надо, компьютер и знать тут
про adsl ничего не может в принципе. А это касается или встроенных,
или usb-модкмов. PPPoE быть может и с Rthernet, но оно именно PPPoE,
без отношения к dsl.
--
С уважением, Сергей
a_s_y@sama.ru
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2008-04-07 8:45 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2008-04-05 3:33 [Comm] модем ADSL Геннадий Ищенко
2008-04-05 6:08 ` Motsyo Gennadi aka Drool
2008-04-05 6:14 ` Motsyo Gennadi aka Drool
2008-04-07 8:45 ` Sergey
ALT Linux Community general discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
public-inbox-index community
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.community
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git