ALT Linux Community general discussions
 help / color / mirror / Atom feed
From: "Vladimir Scherbaev" <vladimir@altlinux.org>
To: "ALT Linux Community general discussions" <community@lists.altlinux.org>
Subject: Re: [Comm] ALD 4.1.1 RC 11152008. Отладка WiFi на ноутбуке IBM TP R40
Date: Thu, 20 Nov 2008 17:51:59 +0300
Message-ID: <89707fb90811200651j45ca60eakc5531aca9fb88f89@mail.gmail.com> (raw)
In-Reply-To: <40babb620811200628x5cff26a9h61a3f0fde18dec1c@mail.gmail.com>

20 ноября 2008 г. 17:28 пользователь ALT Linux User
<altlinux.mailbox@gmail.com> написал:
> В продолжение.
>
> NetworkManager полностью удалил. В асс выставил DHCP. Вот что получается:
>
> # service network stop
> Computing interface groups: .. 2 interfaces found
> Processing /etc/net/vlantab: empty.
> Stopping group 1/realphys (1 interfaces)
>        Stopping eth0: ..OK
> Stopping group 0/virtual (1 interfaces)
>        Stopping lo: .OK
>
> # service network start
> Computing interface groups: .. 2 interfaces found
> Starting group 0/virtual (1 interfaces)
>        Starting lo: ....OK
> Starting group 1/realphys (1 interfaces)
>        Starting eth0: ..Linux wireless extensions version 22 detected.
> ipw2x00 driver uses driver_wext (-Dwext) instead of driver_ipw.
> ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
> ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
> Failed to set encryption.
> ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
> Failed to set encryption.
> ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
> Failed to set encryption.
> ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
> Failed to set encryption.
> ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
> ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
> OK
> Processing /etc/net/vlantab: empty.
>
> # cat /etc/net/ifaces/eth0/options
> TYPE=eth
> BOOTPROTO=dhcp
> WPA_DRIVER=ipw
> DISABLED=no
> NM_CONTROLLED=no
>
> # cat /etc/net/ifaces/eth0/wpa_supplicant.conf
> ctrl_interface=/var/run/wpa_supplicant
> update_config=1
>
> network={
>        ssid="IMYAREK"
>        scan_ssid=1
>        psk=[long key]
>        proto=WPA
>        key_mgmt=WPA-PSK
>        pairwise=TKIP
> }
>
> # iwconfig
> lo        no wireless extensions.
>
> eth0      unassociated  ESSID:"IMYAREK"  Nickname:"ipw2100"
>          Mode:Managed  Channel=0  Access Point: Not-Associated
>          Bit Rate:0 kb/s   Tx-Power:16 dBm
>          Retry short limit:7   RTS thr:off   Fragment thr:off
>          Encryption key:[key]   Security mode:open
>          Power Management:off
>          Link Quality:0  Signal level:0  Noise level:0
>          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
>          Tx excessive retries:0  Invalid misc:0   Missed beacon:0
>
> # ifconfig
> eth0      Link encap:Ethernet  HWaddr 00:04:23:7C:16:A8
>          UP BROADCAST MULTICAST  MTU:1500  Metric:1
>          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>          collisions:0 txqueuelen:1000
>          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
>          Interrupt:11 Base address:0x8000 Memory:c0204000-c0204fff
>
> lo        Link encap:Local Loopback
>          inet addr:127.0.0.1  Mask:255.0.0.0
>          UP LOOPBACK RUNNING  MTU:16436  Metric:1
>          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>          collisions:0 txqueuelen:0
>          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
>
> # dhcpcd eth0 -d -G 192.168.1.1
> Info, eth0: dhcpcd 3.0.17 starting
> Info, eth0: hardware address = 00:04:23:7c:16:a8
> Info, eth0: broadcasting for a lease
> Debug, eth0: sending DHCP_DISCOVER with xid 0x53b95c96
> Debug, eth0: waiting on select for 20 seconds
> Debug, eth0: sending DHCP_DISCOVER with xid 0x53b95c96
> Debug, eth0: sending DHCP_DISCOVER with xid 0x53b95c96
> Debug, eth0: sending DHCP_DISCOVER with xid 0x53b95c96
> Debug, eth0: sending DHCP_DISCOVER with xid 0x53b95c96
> Debug, eth0: sending DHCP_DISCOVER with xid 0x53b95c96
> Debug, eth0: sending DHCP_DISCOVER with xid 0x53b95c96
> Error, eth0: timed out
> Info, eth0: exiting
>
> Единственное, что приходит на ум: не подхоит драйвер WiFi карточки?
>
> Или, наверное, что-то другое?
>
> Помогите, пожалуйста, наладить.

А можно ещё посмотреть на ваш lsmod?


-- 
With Best Regards,
Vladimir Scherbaev

  reply	other threads:[~2008-11-20 14:51 UTC|newest]

Thread overview: 21+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2008-11-20 11:43 ALT Linux User
2008-11-20 14:28 ` ALT Linux User
2008-11-20 14:51   ` Vladimir Scherbaev [this message]
2008-11-20 15:55     ` ALT Linux User
2008-11-20 16:53 ` Denis Nazarov
2008-11-20 16:59   ` ALT Linux User
2008-11-21 10:57   ` Michael A. Kangin
2008-11-22  8:24   ` Константин Михайленко
2008-11-22  9:01   ` Sergey Shilov
2008-11-22 19:56     ` Anton Farygin
2008-11-22 20:09       ` [Comm] шалезяки D-Link и прошивки к ним (was: ALD 4.1.1 RC 11152008. Отладка WiFi на ноутбуке IBM TP R40) Michael Shigorin
2008-11-22 20:26         ` [Comm] шалезяки D-Link и прошивки к ним Anton Farygin
2008-11-22 23:22       ` [Comm] ALD 4.1.1 RC 11152008. Отладка WiFi на ноутбуке IBM TP R40 [JT] Sergey Shilov
2008-11-23 15:55         ` Anton Farygin
2008-11-23  0:55       ` [Comm] ALD 4.1.1 RC 11152008. Отладка WiFi на ноутбуке IBM TP R40 Pavlov Konstantin
2008-11-23 15:57         ` Anton Farygin
2008-11-24  4:53           ` Denis G. Samsonenko
2008-11-24 10:57             ` Vladimir Scherbaev
2008-11-24 11:15               ` Denis G. Samsonenko
2008-11-24 17:59             ` Denis Nazarov
2008-11-24  6:47       ` Алексей Шенцев

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=89707fb90811200651j45ca60eakc5531aca9fb88f89@mail.gmail.com \
    --to=vladimir@altlinux.org \
    --cc=community@lists.altlinux.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

ALT Linux Community general discussions

This inbox may be cloned and mirrored by anyone:

	git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
		mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
	public-inbox-index community

Example config snippet for mirrors.
Newsgroup available over NNTP:
	nntp://lore.altlinux.org/org.altlinux.lists.community


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git