* [Comm] Как ядро заставить пересчитать устройство?
@ 2013-09-17 8:46 Kharitonov A. Dmitry
2013-09-17 8:52 ` Pavel Vainerman
0 siblings, 1 reply; 3+ messages in thread
From: Kharitonov A. Dmitry @ 2013-09-17 8:46 UTC (permalink / raw)
To: community
Требуется получить получить адекватный UUID
Вставляю SD карту
$ dmesg | tail
[ 289.425392] sd 4:0:0:0: [sde] Mode Sense: 03 00 00 00
[ 289.426736] sd 4:0:0:0: [sde] No Caching mode page present
[ 289.426757] sd 4:0:0:0: [sde] Assuming drive cache: write through
[ 289.436518] sd 4:0:0:0: [sde] No Caching mode page present
[ 289.436536] sd 4:0:0:0: [sde] Assuming drive cache: write through
[ 289.439109] sde: sde1 sde2 < sde5 >
[ 289.444068] sd 4:0:0:0: [sde] No Caching mode page present
[ 289.444092] sd 4:0:0:0: [sde] Assuming drive cache: write through
[ 289.444114] sd 4:0:0:0: [sde] Attached SCSI removable disk
[ 290.576258] FAT-fs (sde1): utf8 is not a recommended IO charset for
FAT filesystems, filesystem will be case sensitive!
$ sudo fdisk -l /dev/sde
Disk /dev/sde: 32.3 GB, 32295092224 bytes, 63076352 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x001105d9
Device Boot Start End Blocks Id System
/dev/sde1 2048 6293503 3145728 c W95 FAT32 (LBA)
/dev/sde2 6293504 63076351 28391424 f W95 Ext'd (LBA)
/dev/sde5 6295552 63076351 28390400 b W95 FAT32
$ sudo blkid | grep /dev/sde
/dev/sde1: LABEL="tr" UUID="C725-949A" TYPE="vfat"
/dev/sde5: LABEL="tr2" UUID="C885-03E6" TYPE="vfat"
Внимательно смотрим на UUID="C725-949A"
Это всё правильно. Теперь мне нужно переформатировать в ntfs
$ sudo umount /dev/sde1
$ sudo umount /dev/sde1
umount: /dev/sde1: not mounted
$ sudo umount /dev/sde5
umount: /dev/sde5: not mounted
$ sudo dd if=/dev/zero of=/dev/sde count=8k bs=4096
8192+0 records in
8192+0 records out
33554432 bytes (34 MB) copied, 2.94593 s, 11.4 MB/s
$ echo -ne "u\nc\nn\np\n\n\n\nt\n7\na\n1\nw\n" | sudo fdisk -S56 /dev/sde
Welcome to fdisk (util-linux 2.22.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Device does not contain a recognized partition table
Building a new DOS disklabel with disk identifier 0x218d0787.
Command (m for help): Changing display/entry units to cylinders
(DEPRECATED!)
Command (m for help): DOS Compatibility flag is set (DEPRECATED!)
Command (m for help): Partition type:
p primary (0 primary, 0 extended, 4 free)
e extended
Select (default p): Partition number (1-4, default 1): Using default value 1
First cylinder (1-17599, default 1): Using default value 1
Last cylinder, +cylinders or +size{K,M,G} (1-17599, default 17599):
Using default value 17599
Partition 1 of type Linux and of size 30.1 GiB is set
Command (m for help): Selected partition 1
Hex code (type L to list codes): Changed system type of partition 1 to 7
(HPFS/NTFS/exFAT)
Command (m for help): Partition number (1-4):
Command (m for help): The partition table has been altered!
Calling ioctl() to re-read partition table.
Syncing disks.
$ sudo fdisk -l /dev/sde
Disk /dev/sde: 32.3 GB, 32295092224 bytes, 63076352 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x218d0787
Device Boot Start End Blocks Id System
/dev/sde1 * 56 63074815 31537380 7 HPFS/NTFS/exFAT
$ sudo mkfs.ntfs -f -c 4096 -L test /dev/sde1
Creating NTFS volume structures.
mkntfs completed successfully. Have a nice day.
А теперь внимание
$ sudo blkid | grep /dev/sde
/dev/sde1: LABEL="tr" UUID="C725-949A" TYPE="vfat"
UUID не изменился!!!
$ sudo partprobe
$ sudo blkid | grep /dev/sde
/dev/sde1: LABEL="tr" UUID="C725-949A" TYPE="vfat"
вынимаю и вставляю
$ dmesg | tail
[ 918.870892] sd 5:0:0:0: [sde] Write Protect is off
[ 918.870910] sd 5:0:0:0: [sde] Mode Sense: 03 00 00 00
[ 918.872078] sd 5:0:0:0: [sde] No Caching mode page present
[ 918.872093] sd 5:0:0:0: [sde] Assuming drive cache: write through
[ 918.877223] sd 5:0:0:0: [sde] No Caching mode page present
[ 918.877233] sd 5:0:0:0: [sde] Assuming drive cache: write through
[ 918.878631] sde: sde1
[ 918.882372] sd 5:0:0:0: [sde] No Caching mode page present
[ 918.882382] sd 5:0:0:0: [sde] Assuming drive cache: write through
[ 918.882390] sd 5:0:0:0: [sde] Attached SCSI removable disk
$ sudo blkid | grep /dev/sde
/dev/sde1: LABEL="tr" UUID="C725-949A" TYPE="vfat"
После перезагрузки
$ dmesg | tail
[ 139.522377] sd 4:0:0:0: [sde] Mode Sense: 03 00 00 00
[ 139.523479] sd 4:0:0:0: [sde] No Caching mode page present
[ 139.523495] sd 4:0:0:0: [sde] Assuming drive cache: write through
[ 139.531353] sd 4:0:0:0: [sde] No Caching mode page present
[ 139.531369] sd 4:0:0:0: [sde] Assuming drive cache: write through
[ 139.532754] sde: sde1
[ 139.536356] sd 4:0:0:0: [sde] No Caching mode page present
[ 139.536369] sd 4:0:0:0: [sde] Assuming drive cache: write through
[ 139.536381] sd 4:0:0:0: [sde] Attached SCSI removable disk
[ 144.687148] fuse init (API version 7.20)
$ sudo blkid | grep /dev/sde
/dev/sde1: LABEL="test" UUID="2130BC3E3BF9C94B" TYPE="ntfs"
За какую ручку дёргать чтоб не перезагружаться?
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [Comm] Как ядро заставить пересчитать устройство?
2013-09-17 8:46 [Comm] Как ядро заставить пересчитать устройство? Kharitonov A. Dmitry
@ 2013-09-17 8:52 ` Pavel Vainerman
2013-09-18 3:53 ` Kharitonov A. Dmitry
0 siblings, 1 reply; 3+ messages in thread
From: Pavel Vainerman @ 2013-09-17 8:52 UTC (permalink / raw)
To: ALT Linux Community general discussions
17.09.2013 12:46, Kharitonov A. Dmitry пишет:
> Требуется получить получить адекватный UUID
>
> Вставляю SD карту
> $ dmesg | tail
> [ 289.425392] sd 4:0:0:0: [sde] Mode Sense: 03 00 00 00
> [ 289.426736] sd 4:0:0:0: [sde] No Caching mode page present
> [ 289.426757] sd 4:0:0:0: [sde] Assuming drive cache: write through
> [ 289.436518] sd 4:0:0:0: [sde] No Caching mode page present
> [ 289.436536] sd 4:0:0:0: [sde] Assuming drive cache: write through
> [ 289.439109] sde: sde1 sde2 < sde5 >
> [ 289.444068] sd 4:0:0:0: [sde] No Caching mode page present
> [ 289.444092] sd 4:0:0:0: [sde] Assuming drive cache: write through
> [ 289.444114] sd 4:0:0:0: [sde] Attached SCSI removable disk
> [ 290.576258] FAT-fs (sde1): utf8 is not a recommended IO charset for
> FAT filesystems, filesystem will be case sensitive!
> $ sudo fdisk -l /dev/sde
>
> Disk /dev/sde: 32.3 GB, 32295092224 bytes, 63076352 sectors
> Units = sectors of 1 * 512 = 512 bytes
> Sector size (logical/physical): 512 bytes / 512 bytes
> I/O size (minimum/optimal): 512 bytes / 512 bytes
> Disk identifier: 0x001105d9
>
> Device Boot Start End Blocks Id System
> /dev/sde1 2048 6293503 3145728 c W95 FAT32 (LBA)
> /dev/sde2 6293504 63076351 28391424 f W95 Ext'd (LBA)
> /dev/sde5 6295552 63076351 28390400 b W95 FAT32
> $ sudo blkid | grep /dev/sde
> /dev/sde1: LABEL="tr" UUID="C725-949A" TYPE="vfat"
> /dev/sde5: LABEL="tr2" UUID="C885-03E6" TYPE="vfat"
>
> Внимательно смотрим на UUID="C725-949A"
> Это всё правильно. Теперь мне нужно переформатировать в ntfs
>
> $ sudo umount /dev/sde1
> $ sudo umount /dev/sde1
> umount: /dev/sde1: not mounted
> $ sudo umount /dev/sde5
> umount: /dev/sde5: not mounted
> $ sudo dd if=/dev/zero of=/dev/sde count=8k bs=4096
> 8192+0 records in
> 8192+0 records out
> 33554432 bytes (34 MB) copied, 2.94593 s, 11.4 MB/s
> $ echo -ne "u\nc\nn\np\n\n\n\nt\n7\na\n1\nw\n" | sudo fdisk -S56 /dev/sde
> Welcome to fdisk (util-linux 2.22.1).
>
> Changes will remain in memory only, until you decide to write them.
> Be careful before using the write command.
>
> Device does not contain a recognized partition table
> Building a new DOS disklabel with disk identifier 0x218d0787.
>
> Command (m for help): Changing display/entry units to cylinders
> (DEPRECATED!)
>
> Command (m for help): DOS Compatibility flag is set (DEPRECATED!)
>
> Command (m for help): Partition type:
> p primary (0 primary, 0 extended, 4 free)
> e extended
> Select (default p): Partition number (1-4, default 1): Using default
> value 1
> First cylinder (1-17599, default 1): Using default value 1
> Last cylinder, +cylinders or +size{K,M,G} (1-17599, default 17599):
> Using default value 17599
> Partition 1 of type Linux and of size 30.1 GiB is set
>
> Command (m for help): Selected partition 1
> Hex code (type L to list codes): Changed system type of partition 1 to 7
> (HPFS/NTFS/exFAT)
>
> Command (m for help): Partition number (1-4):
> Command (m for help): The partition table has been altered!
>
> Calling ioctl() to re-read partition table.
> Syncing disks.
> $ sudo fdisk -l /dev/sde
>
> Disk /dev/sde: 32.3 GB, 32295092224 bytes, 63076352 sectors
> Units = sectors of 1 * 512 = 512 bytes
> Sector size (logical/physical): 512 bytes / 512 bytes
> I/O size (minimum/optimal): 512 bytes / 512 bytes
> Disk identifier: 0x218d0787
>
> Device Boot Start End Blocks Id System
> /dev/sde1 * 56 63074815 31537380 7 HPFS/NTFS/exFAT
> $ sudo mkfs.ntfs -f -c 4096 -L test /dev/sde1
> Creating NTFS volume structures.
> mkntfs completed successfully. Have a nice day.
>
> А теперь внимание
>
> $ sudo blkid | grep /dev/sde
> /dev/sde1: LABEL="tr" UUID="C725-949A" TYPE="vfat"
>
> UUID не изменился!!!
>
> $ sudo partprobe
> $ sudo blkid | grep /dev/sde
> /dev/sde1: LABEL="tr" UUID="C725-949A" TYPE="vfat"
>
> вынимаю и вставляю
>
> $ dmesg | tail
> [ 918.870892] sd 5:0:0:0: [sde] Write Protect is off
> [ 918.870910] sd 5:0:0:0: [sde] Mode Sense: 03 00 00 00
> [ 918.872078] sd 5:0:0:0: [sde] No Caching mode page present
> [ 918.872093] sd 5:0:0:0: [sde] Assuming drive cache: write through
> [ 918.877223] sd 5:0:0:0: [sde] No Caching mode page present
> [ 918.877233] sd 5:0:0:0: [sde] Assuming drive cache: write through
> [ 918.878631] sde: sde1
> [ 918.882372] sd 5:0:0:0: [sde] No Caching mode page present
> [ 918.882382] sd 5:0:0:0: [sde] Assuming drive cache: write through
> [ 918.882390] sd 5:0:0:0: [sde] Attached SCSI removable disk
> $ sudo blkid | grep /dev/sde
> /dev/sde1: LABEL="tr" UUID="C725-949A" TYPE="vfat"
>
>
> После перезагрузки
>
> $ dmesg | tail
> [ 139.522377] sd 4:0:0:0: [sde] Mode Sense: 03 00 00 00
> [ 139.523479] sd 4:0:0:0: [sde] No Caching mode page present
> [ 139.523495] sd 4:0:0:0: [sde] Assuming drive cache: write through
> [ 139.531353] sd 4:0:0:0: [sde] No Caching mode page present
> [ 139.531369] sd 4:0:0:0: [sde] Assuming drive cache: write through
> [ 139.532754] sde: sde1
> [ 139.536356] sd 4:0:0:0: [sde] No Caching mode page present
> [ 139.536369] sd 4:0:0:0: [sde] Assuming drive cache: write through
> [ 139.536381] sd 4:0:0:0: [sde] Attached SCSI removable disk
> [ 144.687148] fuse init (API version 7.20)
> $ sudo blkid | grep /dev/sde
> /dev/sde1: LABEL="test" UUID="2130BC3E3BF9C94B" TYPE="ntfs"
>
> За какую ручку дёргать чтоб не перезагружаться?
наверно возможно так
blockdev --rereadpt /dev/sde
--
Pavel Vainerman
www.etersot.ru
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [Comm] Как ядро заставить пересчитать устройство?
2013-09-17 8:52 ` Pavel Vainerman
@ 2013-09-18 3:53 ` Kharitonov A. Dmitry
0 siblings, 0 replies; 3+ messages in thread
From: Kharitonov A. Dmitry @ 2013-09-18 3:53 UTC (permalink / raw)
To: ALT Linux Community general discussions
>> $ sudo blkid | grep /dev/sde
>> /dev/sde1: LABEL="test" UUID="2130BC3E3BF9C94B" TYPE="ntfs"
>>
>> За какую ручку дёргать чтоб не перезагружаться?
>
> наверно возможно так
> blockdev --rereadpt /dev/sde
>
Не помогло. Здесь наверное не только партицию надо заставлять
пересчитывать. Надо как-то заголовок FS пересчитать.
Похоже эта же болезнь есть у установщика дистрибутива на этапе разбиения
дисков.
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2013-09-18 3:53 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-09-17 8:46 [Comm] Как ядро заставить пересчитать устройство? Kharitonov A. Dmitry
2013-09-17 8:52 ` Pavel Vainerman
2013-09-18 3:53 ` Kharitonov A. Dmitry
ALT Linux Community general discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
public-inbox-index community
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.community
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git