ALT Linux Community general discussions
 help / color / mirror / Atom feed
From: Yuriy <law@freemail.com.ua>
To: ALT Linux Community general discussions <community@lists.altlinux.org>
Subject: Re: [Comm] установить wifi D-Link DWA 520 (PCI) одновременно с сетевой картой
Date: Thu, 16 Jul 2009 18:01:02 +0300
Message-ID: <4A5F40AE.8010508@freemail.com.ua> (raw)
In-Reply-To: <6c7be88d0907152303k2334e1e1h55fff196547bc748@mail.gmail.com>

[-- Attachment #1: Type: text/plain, Size: 1071 bytes --]

Dmitriy Kruglikov пишет:
> 16 июля 2009 г. 0:52 пользователь Yuriy написал:
> Ну вот, это, похоже, и есть причина (или следствие)
>> ath5k_pci 0000:00:0f.0: registered as 'phy0'
> Вычитался кривой MAC...
>> ath5k phy0: failed to wakeup the MAC Chip
>> ACPI: PCI interrupt for device 0000:00:0f.0 disabled
> Прерывания ей не выдано от ACPI ...
>> ath5k_pci: probe of 0000:00:0f.0 failed with error -5
> Естественно, вывалились с ошибкой ...
> 
> Совет подвигать по слотам должен помочь...
> 


Да, огромное спасибо!
Появилась!!! (подвигал по слотам) - пол дела сделано! )

Выводы команд прилагаю аттачами.


Теперь мне нужно сделать точку доступа wifi ad-hoc, чтобы инет который 
на копм получаю по сетевой карте (черезADSL модем) через точку доступа 
wifi ad-hoc раздать на мобильный.

Первый же ком блином:
[root@localhost ttt]# iwconfig ath0 mode Ad-Hoc
Error for wireless request "Set Mode" (8B06) :
     SET failed on device ath0 ; Invalid argument.
[root@localhost ttt]#


Подскажите плиз что делать, или где есть ссылки на инструкции, чтоб 
установить.

Спасибо!



[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 2135 bytes --]

ACPI: PCI interrupt for device 0000:00:0b.0 disabled
ath_pci: driver unloaded
ath_pci: madwifi-dfs
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
MadWifi: ath_attach: Interference mitigation support exists, but initially disabled by intmit module parameter.
MadWifi: ath_attach: Switching rfkill capability off
MadWifi: ath_attach: Switching per-packet transmit power control off
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: ath_announce: Use hw queue 1 for WME_AC_BE traffic
wifi0: ath_announce: Use hw queue 0 for WME_AC_BK traffic
wifi0: ath_announce: Use hw queue 2 for WME_AC_VI traffic
wifi0: ath_announce: Use hw queue 3 for WME_AC_VO traffic
wifi0: ath_announce: Use hw queue 8 for CAB traffic
wifi0: ath_announce: Use hw queue 9 for beacons
ath_pci: wifi0: Atheros 5212: mem=0xd8020000, irq=10
ACPI: PCI interrupt for device 0000:00:0b.0 disabled
ath_pci: driver unloaded
ath_pci: madwifi-dfs
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
MadWifi: ath_attach: Interference mitigation support exists, but initially disabled by intmit module parameter.
MadWifi: ath_attach: Switching rfkill capability off
MadWifi: ath_attach: Switching per-packet transmit power control off
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: ath_announce: Use hw queue 1 for WME_AC_BE traffic
wifi0: ath_announce: Use hw queue 0 for WME_AC_BK traffic
wifi0: ath_announce: Use hw queue 2 for WME_AC_VI traffic
wifi0: ath_announce: Use hw queue 3 for WME_AC_VO traffic
wifi0: ath_announce: Use hw queue 8 for CAB traffic
wifi0: ath_announce: Use hw queue 9 for beacons
ath_pci: wifi0: Atheros 5212: mem=0xd8020000, irq=10


[-- Attachment #3: ifconfig.txt --]
[-- Type: text/plain, Size: 890 bytes --]

eth0      Link encap:Ethernet  HWaddr 00:0E:2E:A6:9D:2B  
          inet addr:192.168.1.3  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:496 errors:0 dropped:0 overruns:0 frame:0
          TX packets:585 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:337130 (329.2 KiB)  TX bytes:98554 (96.2 KiB)
          Interrupt:11 Base address:0x4000 

..................................

wifi0     Link encap:UNSPEC  HWaddr 00-1E-58-AE-94-D0-D8-6B-00-00-00-00-00-00-00-00  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:195 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:10 


[-- Attachment #4: iwconfig.txt --]
[-- Type: text/plain, Size: 651 bytes --]

[root@localhost ttt]# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

vboxnet0  no wireless extensions.

wifi0     no wireless extensions.

ath0      IEEE 802.11b  ESSID:"MY-HOME-NET"  Nickname:""
          Mode:Managed  Channel:0  Access Point: Not-Associated
	  Bit Rate:0 kb/s   Tx-Power:18 dBm   Sensitivity=1/1
	  Retry:off   RTS thr:off   Fragment thr:off
	  Encryption key:off
	  Power Management:off
	  Link Quality=0/70  Signal level=-98 dBm  Noise level=-98 dBm
	  Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
	  Tx excessive retries:0  Invalid misc:0   Missed beacon:0
[root@localhost ttt]#      

  reply	other threads:[~2009-07-16 15:01 UTC|newest]

Thread overview: 16+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2009-07-15 11:57 Yuriy
2009-07-15 12:55 ` Sergey Shilov
2009-07-15 15:03   ` Yuriy
2009-07-15 14:25     ` Dmitriy Kruglikov
2009-07-15 16:18       ` Yuriy
2009-07-15 16:27         ` Yuriy
2009-07-15 17:01           ` Denis Nazarov
2009-07-15 21:23             ` Yuriy
2009-07-15 17:18     ` Sergey Shilov
2009-07-15 21:52       ` Yuriy
2009-07-16  6:03         ` Dmitriy Kruglikov
2009-07-16 15:01           ` Yuriy [this message]
2009-07-16 17:09             ` Sergey Shilov
2009-07-16 13:13         ` Sergey Shilov
2009-07-16 13:20           ` Dmitriy Kruglikov
2009-07-15 22:08 ` Michael Shigorin

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=4A5F40AE.8010508@freemail.com.ua \
    --to=law@freemail.com.ua \
    --cc=community@lists.altlinux.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

ALT Linux Community general discussions

This inbox may be cloned and mirrored by anyone:

	git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
		mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
	public-inbox-index community

Example config snippet for mirrors.
Newsgroup available over NNTP:
	nntp://lore.altlinux.org/org.altlinux.lists.community


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git