From: AdMaks <admaks@gmail.com>
To: ALT Linux Community general discussions <community@lists.altlinux.org>
Subject: [Comm] прерывания и его назначения устройствам (ACPI .... Couldn't register serial port ...)
Date: Sat, 19 Jan 2008 01:01:10 +0300
Message-ID: <479121A6.4010005@gmail.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 6091 bytes --]
Привет
есть ПК, установлен ALS4,
мать... какой-то двух-ядреный слотовый АСУС. кажется p2b
установлено два камня, слотовые так сказать...
ну и потребовалось поставить 4 момеда, на pci
смотрю, глюки... нет двух момедов...
осмотр dmesg показал, что два устройства не смогли быть зарегистрированы
Вапрос -
1) как поймать два потеряных устройства
2) как разлулить именования устройств?
сейчас имена ttyS0&ttyS3 принадлежат pci-модемам, а ttyS1&ttyS2 - com1&com2.
насколько я понимаю -
ttyS0 - com1
ttyS1 - com2
а у меня как-то не так...
я хочу еше 2 внешних модема поставить... на эти ком-порты...
3) в dmesg -ругань на "irqpool"...
параметр к ядру в lilo.conf:
append="irqpool"
был ли я прав указав такое? что должно быть?
.............
isapnp: Scanning for PnP cards...
isapnp: Card '3Com 3C509B EtherLink III'
isapnp: 1 Plug & Play card detected total
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
00:09: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 19 (level, low) -> IRQ 177
0000:00:09.0: ttyS0 at I/O 0xb000 (irq = 177) is a 16550A
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 185
0000:00:0a.0: ttyS3 at I/O 0xa800 (irq = 185) is a 16550A
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) -> IRQ 193
Couldn't register serial port 0000:00:0b.0: -28
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 16 (level, low) -> IRQ 201
Couldn't register serial port 0000:00:0c.0: -28
.................
# cat /proc/interrupts
CPU0 CPU1
0: 1312007 3209707 IO-APIC-edge timer
1: 617 1693 IO-APIC-edge i8042
3: 590 422 IO-APIC-edge serial
4: 435 603 IO-APIC-edge serial
5: 0 0 IO-APIC-edge parport0
6: 3 0 IO-APIC-edge floppy
8: 0 1 IO-APIC-edge rtc
11: 4665 9749 IO-APIC-edge eth0
12: 145 157 IO-APIC-edge i8042
14: 12923 21391 IO-APIC-edge ide0
169: 50001 49999 IO-APIC-level acpi
177: 314 323 IO-APIC-level uhci_hcd:usb1, serial
185: 1424 1435 IO-APIC-level serial
NMI: 0 0
LOC: 4521798 4521782
ERR: 0
MIS: 0
# lspci -v
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host
bridge (rev 03)
Flags: bus master, medium devsel, latency 64
Memory at e4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP
bridge (rev 03) (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: e2000000-e2efffff
Prefetchable memory behind bridge: e2f00000-e3ffffff
00:04.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
Flags: bus master, medium devsel, latency 0
00:04.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev
01) (prog-if 80 [Master])
Flags: bus master, medium devsel, latency 0
I/O ports at b800 [size=16]
00:04.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev
01) (prog-if 00 [UHCI])
Flags: bus master, medium devsel, latency 64, IRQ 177
I/O ports at b400 [size=32]
00:04.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
Flags: medium devsel, IRQ 9
00:09.0 Serial controller: 3Com Corp, Modem Division 56K FaxModem Model
5610 (rev 01) (prog-if 02 [16550])
Subsystem: 3Com Corp, Modem Division USR 56k Internal FAX Modem
(Model 2977)
Flags: medium devsel, IRQ 177
I/O ports at b000 [size=8]
Capabilities: [dc] Power Management version 2
00:0a.0 Serial controller: 3Com Corp, Modem Division 56K FaxModem Model
5610 (rev 01) (prog-if 02 [16550])
Subsystem: 3Com Corp, Modem Division USR 56k Internal FAX Modem
(Model 2977)
Flags: medium devsel, IRQ 185
I/O ports at a800 [size=8]
Capabilities: [dc] Power Management version 2
00:0b.0 Serial controller: 3Com Corp, Modem Division 56K FaxModem Model
5610 (rev 01) (prog-if 02 [16550])
Subsystem: 3Com Corp, Modem Division USR 56k Internal FAX Modem
(Model 2977)
Flags: medium devsel, IRQ 193
I/O ports at a400 [size=8]
Capabilities: [dc] Power Management version 2
00:0c.0 Serial controller: 3Com Corp, Modem Division 56K FaxModem Model
5610 (rev 01) (prog-if 02 [16550])
Subsystem: 3Com Corp, Modem Division USR 56k Internal FAX Modem
(Model 2977)
Flags: medium devsel, IRQ 201
I/O ports at a000 [size=8]
Capabilities: [dc] Power Management version 2
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP
1X/2X (rev 5c) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Rage Pro Turbo AGP 2X
Flags: bus master, stepping, medium devsel, latency 64, IRQ 10
Memory at e3000000 (32-bit, prefetchable) [size=16M]
I/O ports at d800 [size=256]
Memory at e2000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at e2fe0000 [disabled] [size=128K]
Capabilities: [50] AGP version 1.0
полный dmesg приложен
kernel - 2.6.18-ovz-smp-alt17
спасибо
[-- Attachment #2: dmesg4.gz --]
[-- Type: application/gzip, Size: 5238 bytes --]
next reply other threads:[~2008-01-18 22:01 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-01-18 22:01 AdMaks [this message]
2008-01-19 13:06 ` Sergey Vlasov
2008-01-19 19:20 ` Maks Re
2008-01-19 20:44 ` Sergey Vlasov
2008-01-19 20:56 ` AdMaks
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=479121A6.4010005@gmail.com \
--to=admaks@gmail.com \
--cc=community@lists.altlinux.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
ALT Linux Community general discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
public-inbox-index community
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.community
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git