[Comm] Oops: переодически высыпается кернел

[Comm] Oops: переодически высыпается кернел

[Dmitry Rusetsky]

[-- Attachment #1: Type: text/plain, Size: 359 bytes --]

Добрый всем день!
Уже замучился с проблемой!
AltMaster. Xeon 2 CPU 2G RAM
Переодически высыпается кернел (2.6.9-std26-smp-alt11) с ошибкой

Unable to handle kernel NULL pointer dereference at virtual address 0000000d

адреса и приложения бывают разные!

Может кто сталкивался?
Поможите!

dmegs и кусок messages прилагаются!

-- 
С Уважением Русецкий Дмитрий.

[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 15424 bytes --]

che decay timeout: 2 msecs.
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay loop... 6111.23 BogoMIPS (lpj=3055616)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps:  bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps:        bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Xeon(TM) CPU 3.06GHz stepping 09
Booting processor 2/6 eip 3000
Initializing CPU#2
Calibrating delay loop... 6094.84 BogoMIPS (lpj=3047424)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps:  bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU: After all inits, caps:        bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: Intel P4/Xeon Extended MCE MSRs (12) available
CPU2: Thermal monitoring enabled
CPU2: Intel(R) Xeon(TM) CPU 3.06GHz stepping 09
Booting processor 3/7 eip 3000
Initializing CPU#3
Calibrating delay loop... 6094.84 BogoMIPS (lpj=3047424)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps:  bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU: After all inits, caps:        bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: Intel P4/Xeon Extended MCE MSRs (12) available
CPU3: Thermal monitoring enabled
CPU3: Intel(R) Xeon(TM) CPU 3.06GHz stepping 09
Total of 4 processors activated (24363.00 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 4 CPUs: passed.
Brought up 4 CPUs
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 289k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.20 entry at 0xecdfa, last bus=5
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7f90
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x6a78, dseg 0xf0000
PnPBIOS: 18 nodes reported by PnP BIOS; 18 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI interrupt 0000:05:02.0[A] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI interrupt 0000:05:0c.0[A] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI interrupt 0000:05:0c.1[B] -> GSI 22 (level, low) -> IRQ 22
pnp: 00:12: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:12: ioport range 0xcf8-0xcff could not be reserved
pnp: 00:13: ioport range 0xf800-0xf81f could not be reserved
pnp: 00:13: ioport range 0xf820-0xf83f could not be reserved
pnp: 00:13: ioport range 0xf840-0xf85f has been reserved
pnp: 00:13: ioport range 0xf860-0xf87f has been reserved
pnp: 00:13: ioport range 0xfa00-0xfa1f has been reserved
pnp: 00:13: ioport range 0xfa20-0xfa3f has been reserved
pnp: 00:13: ioport range 0x400-0x41f has been reserved
pnp: 00:13: ioport range 0x420-0x43f has been reserved
Starting balanced_irq
audit: initializing netlink socket (disabled)
audit(1106645358.4294967070:0): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: probe of vesafb0 failed with error -6
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
RAMDISK driver initialized: 16 RAM disks of 12288K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x24a0-0x24a7, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0x24a8-0x24af, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: HL-DT-STDVD-ROM GDR8162B, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide0...
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 16384 buckets, 128Kbytes
TCP: Hash tables configured (established 524288 bind 65536)
NET: Registered protocol family 1
ACPI: (supports S0 S1 S4 S5)
ACPI wakeup devices: 
PCI0  HUB COM1 COM2 USB1 USB2 USB3 EUSB PBTN 
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (romfs filesystem) readonly.
SCSI subsystem initialized
ACPI: PCI interrupt 0000:05:0c.0[A] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI interrupt 0000:05:0c.1[B] -> GSI 22 (level, low) -> IRQ 22
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11
        <Adaptec AIC7902 Ultra320 SCSI adapter>
        aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs

(scsi0:A:0): 320.000MB/s transfers (160.000MHz DT|IU|QAS, 16bit)
(scsi0:A:1): 320.000MB/s transfers (160.000MHz DT|IU|QAS, 16bit)
  Vendor: SEAGATE   Model: ST336607LW        Rev: HPS4
  Type:   Direct-Access                      ANSI SCSI revision: 03
scsi0:A:0:0: Tagged Queuing enabled.  Depth 32
SCSI device sda: 71132960 512-byte hdwr sectors (36420 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 < sda5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
  Vendor: SEAGATE   Model: ST336607LW        Rev: HPS4
  Type:   Direct-Access                      ANSI SCSI revision: 03
scsi0:A:1:0: Tagged Queuing enabled.  Depth 32
SCSI device sdb: 71132960 512-byte hdwr sectors (36420 MB)
SCSI device sdb: drive cache: write back
 sdb: sdb1
Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11
        <Adaptec AIC7902 Ultra320 SCSI adapter>
        aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs

EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: sda1: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 278129
EXT3-fs: sda1: 1 orphan inode deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
VFS: Busy inodes after unmount. Self-destruct in 5 seconds.  Have a nice day...
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 208k freed
Executing init=/sbin/init
Real Time Clock Driver v1.12
Adding 297128k swap on /dev/sda5.  Priority:-1 extents:1
EXT3 FS on sda1, internal journal
alps.c: E6 report: 1a 03 3c
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
Linux agpgart interface v0.100 (c) Dave Jones
ts: Compaq touchscreen protocol output
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
tg3.c:v3.10 (September 14, 2004)
ACPI: PCI interrupt 0000:05:02.0[A] -> GSI 21 (level, low) -> IRQ 21
divert: allocating divert_blk for eth0
eth0: Tigon3 [partno(BCM95702A20) rev 1002 PHY(5703)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:0d:9d:57:8a:b6
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] 
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 23, pci mem f882c000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 16, io base 00002440
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 19, io base 00002460
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ACPI: Power Button (FF) [PWRF]
input: PC Speaker
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
ichxrom ichxrom_init_one(): Unable to register resource 0xff000000-0xffffffff - kernel bug?
ichxrom: firmware access control, I can't enable writes
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49591 usecs
intel8x0: clocking to 48000
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module  1.0-6111  Tue Jul 27 07:55:38 PDT 2004
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
lp0: using parport0 (interrupt-driven).
vmmon: no version for "struct_module" found: kernel tainted.
vmmon: no version magic, tainting kernel.
/dev/vmmon: Module vmmon: registered with major=10 minor=165
/dev/vmmon: Module vmmon: initialized
vmnet: no version magic, tainting kernel.
/dev/vmnet: open called by PID 4117 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: enabling the bridge
bridge-eth0: up
bridge-eth0: already up
bridge-eth0: attached
/dev/vmnet: open called by PID 4137 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
divert: allocating divert_blk for vmnet1
/dev/vmnet: open called by PID 4169 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
warning: process `update' used the obsolete bdflush system call
Fix your initscripts?
apm: BIOS not found.
warning: process `update' used the obsolete bdflush system call
Fix your initscripts?
usb 3-2: new full speed USB device using address 2
usb 3-2: device not accepting address 2, error -71
usb 3-2: new full speed USB device using address 3
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
  Vendor:           Model:                   Rev: 1.89
  Type:   Direct-Access                      ANSI SCSI revision: 02
sdc: Unit Not Ready, sense:
Current : sense key Unit Attention
Additional sense: Not ready to ready change, medium may have changed
SCSI device sdc: 256000 512-byte hdwr sectors (131 MB)
sdc: Write Protect is off
sdc: Mode Sense: 03 00 00 00
sdc: assuming drive cache: write through
 sdc: sdc1
Attached scsi removable disk sdc at scsi2, channel 0, id 0, lun 0
USB Mass Storage device found at 3
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb 3-2: USB disconnect, address 3
usb 3-2: new full speed USB device using address 4
usb 3-2: device not accepting address 4, error -71
usb 3-2: new full speed USB device using address 5
scsi3 : SCSI emulation for USB Mass Storage devices
  Vendor:           Model:                   Rev: 1.89
  Type:   Direct-Access                      ANSI SCSI revision: 02
sdc: Unit Not Ready, sense:
Current : sense key Unit Attention
Additional sense: Not ready to ready change, medium may have changed
SCSI device sdc: 256000 512-byte hdwr sectors (131 MB)
sdc: Write Protect is off
sdc: Mode Sense: 03 00 00 00
sdc: assuming drive cache: write through
 sdc: sdc1
Attached scsi removable disk sdc at scsi3, channel 0, id 0, lun 0
USB Mass Storage device found at 5

[-- Attachment #3: oops.txt --]
[-- Type: text/plain, Size: 2755 bytes --]


Jan 25 09:27:20 dima kernel: Unable to handle kernel NULL pointer dereference at virtual address 0000000d
Jan 25 09:27:20 dima kernel:  printing eip:
Jan 25 09:27:20 dima kernel: c01618ef
Jan 25 09:27:20 dima kernel: *pde = 00000000
Jan 25 09:27:20 dima kernel: Oops: 0000 [#2]
Jan 25 09:27:20 dima kernel: SMP 
Jan 25 09:27:20 dima kernel: Modules linked in: isofs zlib_inflate snd_pcm_oss snd_mixer_oss vmnet vmmon lp ide_cd cdrom nvidia snd_intel8x0 snd_ac97_codec snd_pcm snd_timer snd_page_alloc gameport snd_mpu401_uart snd_rawmidi snd_seq_device snd soundcore pcspkr button 8250_pnp 8250 serial_core parport_pc parport uhci_hcd ehci_hcd usbcore nls_cp866 nls_koi8_r ncpfs tg3 dm_mod tsdev evdev nvidia_agp agpgart psmouse rtc ext3 jbd aic79xx sd_mod scsi_mod
Jan 25 09:27:20 dima kernel: CPU:    3
Jan 25 09:27:20 dima kernel: EIP:    0060:[pipe_poll+15/96]    Tainted: PF  VLI
Jan 25 09:27:20 dima kernel: EIP:    0060:[<c01618ef>]    Tainted: PF  VLI
Jan 25 09:27:20 dima kernel: EFLAGS: 00210286   (2.6.9-std26-smp-alt11) 
Jan 25 09:27:20 dima kernel: EIP is at pipe_poll+0xf/0x60
Jan 25 09:27:20 dima kernel: eax: 00000001   ebx: 00000145   ecx: eb6c3fa0   edx: eb6c3f64
Jan 25 09:27:20 dima kernel: esi: f7fb9880   edi: f5fb9880   ebp: 00000006   esp: eb6c3f28
Jan 25 09:27:21 dima kernel: ds: 007b   es: 007b   ss: 0068
Jan 25 09:27:21 dima kernel: Process firefox-bin (pid: 5784, threadinfo=eb6c2000 task=f77319b0)
Jan 25 09:27:21 dima kernel: Stack: 00000145 f7f439b8 c0168340 f7fb9880 eb6c3fa0 f7f43980 eb6c3f64 eb6c3f68 
Jan 25 09:27:21 dima kernel:        00000019 c01683af 00000009 f7f43988 eb6c3f64 eb6c3f68 eb6c2000 eb6c3fa0 
Jan 25 09:27:21 dima kernel:        00000000 00000000 00000009 f7f43980 08f5bf68 c016854a 00000009 f7f43980 
Jan 25 09:27:21 dima kernel: Call Trace:
Jan 25 09:27:21 dima kernel:  [do_pollfd+128/144] do_pollfd+0x80/0x90
Jan 25 09:27:21 dima kernel:  [<c0168340>] do_pollfd+0x80/0x90
Jan 25 09:27:21 dima kernel:  [do_poll+95/192] do_poll+0x5f/0xc0
Jan 25 09:27:21 dima kernel:  [<c01683af>] do_poll+0x5f/0xc0
Jan 25 09:27:21 dima kernel:  [sys_poll+314/512] sys_poll+0x13a/0x200
Jan 25 09:27:21 dima kernel:  [<c016854a>] sys_poll+0x13a/0x200
Jan 25 09:27:21 dima kernel:  [__pollwait+0/160] __pollwait+0x0/0xa0
Jan 25 09:27:21 dima kernel:  [<c01678f0>] __pollwait+0x0/0xa0
Jan 25 09:27:21 dima kernel:  [syscall_call+7/11] syscall_call+0x7/0xb
Jan 25 09:27:21 dima kernel:  [<c0105e77>] syscall_call+0x7/0xb
Jan 25 09:27:21 dima kernel: Code: 80 08 01 00 00 8b 40 10 89 01 89 d8 5b 5e c3 b8 ea ff ff ff eb f6 8d b6 00 00 00 00 56 53 8b 74 24 0c 8b 4c 24 10 85 c9 8b 46 08 <8b> 58 0c 8b 93 08 01 00 00 74 12 85 d2 74 0e 51 52 56 ff 11 83 
Jan 25 09:28:00 dima shutdown[5865]: shutting down for system halt

Re: [Comm] Oops: переодически высыпается кернел

[Alexey Borovskoy]

[-- Attachment #1: Type: text/plain, Size: 346 bytes --]

* Среда 26 Январь 2005 21:59 Dmitry Rusetsky <dimania@mail.ru>

> Добрый всем день!
> Уже замучился с проблемой!
> AltMaster. Xeon 2 CPU 2G RAM
> Переодически высыпается кернел (2.6.9-std26-smp-alt11) с
> ошибкой

Поставьте ядро 2.4. Ветка 2.6 для экстремалов.

-- 
Алексей.
GPG key fingerprint
949B BC0E 2C44 7528 4F63  2753 E37A 9E3F 11F3 BDE1

[-- Attachment #2: signature --]
[-- Type: application/pgp-signature, Size: 189 bytes --]

Re: [Comm] Oops: переодически высыпается кернел

[Dmitry Rusetsky]

Alexey Borovskoy wrote:
> * Среда 26 Январь 2005 21:59 Dmitry Rusetsky <dimania@mail.ru>
> 
>>Добрый всем день!
>>Уже замучился с проблемой!
>>AltMaster. Xeon 2 CPU 2G RAM
>>Переодически высыпается кернел (2.6.9-std26-smp-alt11) с
>>ошибкой
> 
> 
> Поставьте ядро 2.4. Ветка 2.6 для экстремалов.
Это понятно!
Но машина в принципе используется как десктопная.
И хотелось всех прелестей нового ядра.
Да и судя по сизифу скоро поддержки 2.4 тамне будет!
НАПРИМЕР:
---------------------------------------------------------------
--Всем, кому требуется сохранить хоть какую-то функциональность 
--hotplug'а на ядре 2.4 - рекомендуется поставить hotplug на Hold.
skip
-- - изменен внутрении алгоритм детекта точки монтирования sysfs, в 
--связи с этим hotplug окончательно перестает работать на ядрах серии 2.4
skip
-------------------------------------------------------------------------
Так кто-нибуть мжет помочь???

> 
> 
> 
> ------------------------------------------------------------------------
> 
> _______________________________________________
> Community mailing list
> Community@altlinux.ru
> https://lists.altlinux.ru/mailman/listinfo/community


-- 
С Уважением Русецкий Дмитрий.

Re: [Comm] Oops: переодически высыпается кернел

[Mike Lykov]

В сообщении от Четверг 27 Январь 2005 18:34 Dmitry Rusetsky написал:

> Так кто-нибуть мжет помочь???

может. тесты/замена железа.

-- 
Mike Lykov
Samara, "Vesna" parfum company, System administrator