* Re: [Comm] ALT(sisyphus) + lm_sensors + nm256_audio
2003-12-12 11:37 ` Sergey Vlasov
@ 2003-12-13 10:32 ` X-Stranger
2003-12-13 10:50 ` Sergey Vlasov
0 siblings, 1 reply; 6+ messages in thread
From: X-Stranger @ 2003-12-13 10:32 UTC (permalink / raw)
To: community
[-- Attachment #1: Type: text/plain, Size: 2112 bytes --]
Sergey Vlasov wrote:
>On Fri, Dec 12, 2003 at 12:51:42PM +0200, X-Stranger wrote:
>
>
>>Дано:
>>1. Acer TraverMate 723TXV (Notebook). 128 MB RAM, PII-400 Mhz, etc.
>>2. ALTLinux Master 2.2 up to Sisyphus (сегодняшний релиз).
>>3. Ядро 2.4.22-up, установлены модули сенсоров.
>>
>>
>
>Не совсем точно указано ядро - в Сизифе сейчас есть варианты std-up и
>wks-up; также нужно знать номер сборки ("сегодняшний Сизиф" - понятие
>растяжимое, с учётом задержки расползания файлов по зеркалам и т.п.).
>Требуется вывод как минимум uname -r (а лучше uname -a - а то потом
>выясняются всякие фокусы, например, если кто-то пересобирал ядро без
>изменения release).
>
>
>
>>Необходимо выяснить:
>>1. Почему при загрузке машины через несколько секунд после старта
>> сервиса lm_sensors намертво вешается система.
>>2. Почему при загрузке машины (где-то через раз) система вешается
>> на старте сервиса Sound. Модуль звука: nm256_audio. (lm_sensors в
>> данной ситуации не грузятся принципиально).
>>
>>P.S. Сенсоры и звук настроены. Руки - чисто субъективно ровные.
>>
>>
>
>На каком ядре это раньше работало нормально?
>
>
>
Ни на каком. Сначала ставим ALTLinux Master 2.2 - не работает. Апгрейдим
все кроме ядра,
еснна, ничего не меняется. Ставим ядро поновее - картинка та же.
>Загрузите систему с новым ядром, отключив мешающие модули, и покажите
>вывод dmesg и lspci -vv. Также необходимо выяснить, какие модули из
>lm_sensors используются (/etc/sysconfig/sensors, /etc/modules.conf);
>что записано в /etc/modules.
>
>Если включается ACPI, попробуйте частично или полностью отключить его
>поддержку (или поддержку APIC) одним из следующих наборов парамеров
>ядра:
>
> acpi_irq_nobalance
> pci=noacpi
> noapic
> nolapic
> acpi=off
> acpi=off noapic
> acpi=off noapic nolapic
>
>
Прилагаю все вышезапрошенные файлы.
Модуль звука удалось загрузить без проблем пару раз используя
acpi_irq_nobalance. НО, при загрузке микшера (aumix) он вываливается.
Сенсоры не заработали с этими параметрами для ядра.
X.
>------------------------------------------------------------------------
>
[-- Attachment #2: uname.log --]
[-- Type: text/plain, Size: 100 bytes --]
Linux X-Stranger 2.4.22-std-up-alt12 #1 Sat Nov 29 21:48:54 MSK 2003 i686 unknown unknown GNU/Linux
[-- Attachment #3: dmesg.log --]
[-- Type: text/plain, Size: 8091 bytes --]
Linux version 2.4.22-std-up-alt12 (builder@mash.office.altlinux.ru) (gcc version 2.96 20000731 (ALT Linux, build 2.96-alt5)) #1 Sat Nov 29 21:48:54 MSK 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e9800 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
BIOS-e820: 0000000007ff0000 - 0000000007fffc00 (ACPI data)
BIOS-e820: 0000000007fffc00 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000fffe9800 - 0000000100000000 (reserved)
user-defined physical RAM map:
user: 0000000000000000 - 000000000009f800 (usable)
user: 000000000009f800 - 00000000000a0000 (reserved)
user: 00000000000e9800 - 0000000000100000 (reserved)
user: 0000000000100000 - 0000000007ff0000 (usable)
user: 0000000007ff0000 - 0000000007fffc00 (ACPI data)
user: 0000000007fffc00 - 0000000008000000 (ACPI NVS)
user: 00000000fffe9800 - 0000000100000000 (reserved)
0MB HIGHMEM available.
127MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 32752
zone(0): 4096 pages.
zone(1): 28656 pages.
zone(2): 0 pages.
DMI 2.1 present.
19 structures occupying 594 bytes.
DMI table at 0x000F0830.
BIOS Vendor: Phoenix Technologies LTD
BIOS Version: V1.0 R01-D7
BIOS Release: 10/29/99
System Vendor: Acer
Product Name: TravelMate 720
Version:
Serial Number: 9142C0180V944002A8M
Board Vendor: ACER
Board Name: TravelMate 720
Board Version:
ACPI disabled because your bios is from 99 and too old
You can enable it with acpi=force
Kernel command line: BOOT_IMAGE=Linux ro root=306 mem=128M acpi_irq_nobalance
ACPI STATIC SET
Local APIC disabled by BIOS -- reenabling.
Could not enable APIC!
Initializing CPU#0
Detected 399.067 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 796.26 BogoMIPS
Memory: 126820k/131008k available (1192k kernel code, 3800k reserved, 501k data, 132k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU: Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Mobile Pentium II stepping 0a
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20031002
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfd9b4, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX [8086/7110] at 00:04.0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xf6000000, mapped to 0xc8800000, size 2496k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:a670
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture.... found (1024x768, 22471 bytes, v2).
Console: switching to colour frame buffer device 106x34
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:04.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcd0-0xfcd7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfcd8-0xfcdf, BIOS settings: hdc:pio, hdd:pio
hda: IBM-DCXA-210000, ATA DISK drive
blk: queue c02f6880, I/O limit 4095Mb (mask 0xffffffff)
hdc: UJDA520, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 19640880 sectors (10056 MB) w/420KiB Cache, CHS=1222/255/63, UDMA(33)
Partition check:
hda: hda1 hda2 hda3 < hda5 hda6 >
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 121k freed
VFS: Mounted root (romfs filesystem) readonly.
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 132k freed
Executing init=/sbin/init
Real Time Clock Driver v1.10e
Adding Swap: 313232k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xf8000000
NTFS driver 2.1.4b [Flags: R/O MODULE].
NTFS-fs warning (device 03:01): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
NTFS volume version 3.1.
MSDOS FS: IO charset cp1251
MSDOS FS: Using codepage 866
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 00:06.0
PCI: Sharing IRQ 11 with 00:06.1
PCI: Found IRQ 11 for device 00:06.1
PCI: Sharing IRQ 11 with 00:06.0
Yenta IRQ list 0498, PCI irq11
Socket status: 30000020
Yenta IRQ list 0498, PCI irq11
Socket status: 30000006
cs: cb_alloc(bus 2): vendor 0x10b7, device 0x5157
PCI: Enabling device 02:00.0 (0000 -> 0003)
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x220-0x22f 0x330-0x337 0x378-0x37f 0x388-0x38f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
02:00.0: 3Com PCI 3CCFE575BT Cyclone CardBus at 0x4000. Vers LK1.1.18-ac
PCI: Setting latency timer of device 02:00.0 to 64
00:50:04:94:ac:c0, IRQ 11
product code 5457 rev 07.1 date 08-20-99
02:00.0: CardBus functions mapped 10800080->c8b59080
Internal config register is 600000, transceivers 0x40.
8K byte-wide RAM 5:3 Rx:Tx split, MII interface.
phy=0, phyx=24, mii_status=0xffff
phy=1, phyx=0, mii_status=0x7809
MII transceiver found at address 0, status 7809.
Enabling bus-master transmits and whole-frame receives.
02:00.0: scatter/gather enabled. h/w checksums enabled
divert: allocating divert_blk for eth0
NeoMagic 256AV/256ZX audio driver, version 1.1p
PCI: Found IRQ 9 for device 01:00.1
PCI: Sharing IRQ 9 with 01:00.0
NM256: This doesn't look to me like the AC97-compatible version.
You can force the driver to load by passing in the module
parameter:
force_load = 1
More likely, you should be using the appropriate SB-16 or
CS4232 driver instead. (If your BIOS has settings for
IRQ and/or DMA for the sound card, this is *not* the correct
driver to use.)
[-- Attachment #4: lm_sensors --]
[-- Type: text/plain, Size: 1494 bytes --]
# /etc/sysconfig/sensors - Defines modules loaded by /etc/rc.d/init.d/lm_sensors
# Copyright (c) 1998 - 2001 Frodo Looijaard <frodol@dds.nl>
#
# This program is free software; you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
#
#
# See also the lm_sensors homepage at:
# http://www2.lm-sensors.nu/~lm78/index.html
#
# This file is used by /etc/rc.d/init.d/lm_sensors and defines the modules to
# be loaded/unloaded. This file is sourced into /etc/rc.d/init.d/lm_sensors.
#
# The format of this file is a shell script that simply defines the modules
# in order as normal variables with the special names:
# MODULE_0, MODULE_1, MODULE_2, etc.
#
# List the modules that are to be loaded for your system
#
# Generated by sensors-detect on Wed Dec 10 17:00:23 2003
MODULE_0=i2c-piix4
MODULE_1=pcf8574
MODULE_2=adm1021
MODULE_3=pcf8591
MODULE_4=eeprom
[-- Attachment #5: lspci.log --]
[-- Type: text/plain, Size: 6691 bytes --]
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Memory behind bridge: f4000000-f5ffffff
Prefetchable memory behind bridge: f6000000-f7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
00:04.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:04.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at fcd0 [size=16]
00:04.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at fce0 [size=32]
00:04.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:06.0 CardBus bridge: Texas Instruments PCI1251A (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:06.1 CardBus bridge: Texas Instruments PCI1251A (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:08.0 Communication controller: Lucent Microelectronics WinModem 56k (rev 01)
Subsystem: AMBIT Microsystem Corp. Lucent Win Modem
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fedffc00 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at fcc8 [size=8]
Region 2: I/O ports at f800 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Neomagic Corporation NM2200 [MagicGraph 256AV] (rev 20) (prog-if 00 [VGA])
Subsystem: Neomagic Corporation NM2200 [MagicGraph 256AV]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 128 (4000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at f6000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at f5000000 (32-bit, non-prefetchable) [size=4M]
Region 2: Memory at f5400000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.1 Multimedia audio controller: Neomagic Corporation NM2200 [MagicMedia 256AV Audio] (rev 20)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 9
Region 0: Memory at f7000000 (32-bit, prefetchable) [size=4M]
Region 1: Memory at f5500000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 Ethernet controller: 3Com Corporation 3c575 [Megahertz] 10/100 LAN CardBus (rev 01)
Subsystem: 3Com Corporation 3C575 Megahertz 10/100 LAN Cardbus PC Card
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 4000 [size=128]
Region 1: Memory at 10800000 (32-bit, non-prefetchable) [size=128]
Region 2: Memory at 10800080 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 10400000 [size=128K]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[-- Attachment #6: modules --]
[-- Type: text/plain, Size: 252 bytes --]
# /etc/modules: kernel modules to load at boot time.
#
# This file should contain the names of kernel modules that are
# to be loaded at boot time, one per line. Comments begin with
# a `#', and everything on the line after them are ignored.
agpgart
[-- Attachment #7: modules.conf --]
[-- Type: text/plain, Size: 226 bytes --]
pre-install pcmcia_core CARDMGR_OPTS=-f /etc/rc.d/init.d/pcmcia start
alias usb-interface usb-uhci
alias sound-slot-0 nm256_audio
alias eth0 3c59x
# I2C module options
alias char-major-89 i2c-dev
options pcf8591 ignore=0,0x4e
[-- Attachment #8: proc_modules --]
[-- Type: text/plain, Size: 764 bytes --]
autofs4 8244 1 (autoclean)
nm256_audio 67100 0 (unused)
sound 56148 0 [nm256_audio]
soundcore 3684 2 [sound]
ac97 3232 0 [nm256_audio]
3c59x 26000 1
ds 6696 2
yenta_socket 10304 2
pcmcia_core 43360 0 [ds yenta_socket]
nls_cp866 3836 1 (autoclean)
vfat 9516 1 (autoclean)
fat 30744 0 (autoclean) [vfat]
nls_cp1251 3580 2 (autoclean)
ntfs 77484 1 (autoclean)
agpgart 43108 0 (unused)
rtc 6172 0 (autoclean)
ext3 62192 1
jbd 37820 1 [ext3]
^ permalink raw reply [flat|nested] 6+ messages in thread