* [Comm] eepro100 parameters
@ 2003-12-05 9:12 Sergey Degtyaryov
2003-12-06 6:37 ` Dmitry Vodennikov
0 siblings, 1 reply; 3+ messages in thread
From: Sergey Degtyaryov @ 2003-12-05 9:12 UTC (permalink / raw)
To: Community
Доброго дня.
Понадобилось залочить одну из трех сетевых карт на 10Mb/half duplex.
В теории это должно выглядеть как modprobe eepro100 0x10,0,0
Однако никаких ограничений не происходит.
Если же вкатать options eepro100 0x10,0,0 (да и вообще в любой
комбинации) в /etc/modules.conf, то модуль не грузиться вовсе.
Как это сделать правильно?
--
Сергей Дегтярев
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [Comm] eepro100 parameters
2003-12-05 9:12 [Comm] eepro100 parameters Sergey Degtyaryov
@ 2003-12-06 6:37 ` Dmitry Vodennikov
2003-12-06 10:53 ` Sergey Degtyaryov
0 siblings, 1 reply; 3+ messages in thread
From: Dmitry Vodennikov @ 2003-12-06 6:37 UTC (permalink / raw)
To: Sergey Degtyaryov
Добрый день.
Friday, December 5, 2003, 2:12:47 PM, Вы писали:
SD> Понадобилось залочить одну из трех сетевых карт на 10Mb/half duplex.
SD> В теории это должно выглядеть как modprobe eepro100 0x10,0,0
SD> Однако никаких ограничений не происходит.
SD> Если же вкатать options eepro100 0x10,0,0 (да и вообще в любой
SD> комбинации) в /etc/modules.conf, то модуль не грузиться вовсе.
SD> Как это сделать правильно?
Я собирал драйвер для e100, взятый откуда-то с www.intel.com, так там
в man e100 написано несколько по-другому:
insmod e100.o e100_speed_duplex=1 - как раз для 10Mb/half duplex
У меня в /etc/modules стоит так (и работает):
alias eth0 e100
options e100 e100_speed_duplex=2
--
Воденников Д.Ю. http://www.dlv.rt.ru
MCP+Internet
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [Comm] eepro100 parameters
2003-12-06 6:37 ` Dmitry Vodennikov
@ 2003-12-06 10:53 ` Sergey Degtyaryov
0 siblings, 0 replies; 3+ messages in thread
From: Sergey Degtyaryov @ 2003-12-06 10:53 UTC (permalink / raw)
To: community
Dmitry Vodennikov пишет:
> Добрый день.
>
> Friday, December 5, 2003, 2:12:47 PM, Вы писали:
>
> SD> Понадобилось залочить одну из трех сетевых карт на 10Mb/half duplex.
> SD> В теории это должно выглядеть как modprobe eepro100 0x10,0,0
> SD> Однако никаких ограничений не происходит.
> SD> Если же вкатать options eepro100 0x10,0,0 (да и вообще в любой
> SD> комбинации) в /etc/modules.conf, то модуль не грузиться вовсе.
> SD> Как это сделать правильно?
> Я собирал драйвер для e100, взятый откуда-то с www.intel.com, так там
> в man e100 написано несколько по-другому:
> insmod e100.o e100_speed_duplex=1 - как раз для 10Mb/half duplex
>
> У меня в /etc/modules стоит так (и работает):
> alias eth0 e100
> options e100 e100_speed_duplex=2
>
Я сделал через mii-tools
--
Сергей Дегтярев
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2003-12-06 10:53 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2003-12-05 9:12 [Comm] eepro100 parameters Sergey Degtyaryov
2003-12-06 6:37 ` Dmitry Vodennikov
2003-12-06 10:53 ` Sergey Degtyaryov
ALT Linux Community general discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
public-inbox-index community
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.community
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git