From: "Oleg N. Kayunov" <okayunov@mtu-net.ru> To: community@altlinux.ru Subject: [Comm] Re: хорошие и плохие флэши Date: Wed, 22 Oct 2003 06:48:06 +0400 Message-ID: <3F95EFE6.9000902@mtu-net.ru> (raw) In-Reply-To: <20031020085845.0aa61d2c._kaa_@mail.ru> Alexander Kubatkin пишет: >On Sun, 19 Oct 2003 23:53:19 +0400 >"Oleg N. Kayunov" <okayunov@mtu-net.ru> wrote: > > > >>Alexander Kubatkin пишет: >> >> >> >>>после этого можно глянуть в /etc/fstab и увидеть примерно следующее: >>> >>> Увидел: Oct 22 05:36:24 base kernel: usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9 Oct 22 05:36:24 base kernel: usb-uhci.c: Detected 2 ports Oct 22 05:36:25 base kernel: usb.c: new USB bus registered, assigned bus number 1 Oct 22 05:36:25 base kernel: hub.c: USB hub found Oct 22 05:36:25 base kernel: hub.c: 2 ports detected Oct 22 05:36:25 base kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver Oct 22 05:36:25 base usb: Loading USB interface (usb-uhci): succeeded Oct 22 05:36:25 base kernel: hub.c: new USB device 00:04.2-1, assigned address 2 Oct 22 05:36:25 base kernel: hub.c: USB hub found Oct 22 05:36:25 base kernel: hub.c: 5 ports detected Oct 22 05:36:25 base usb: Mounting USB filesystem: succeeded Oct 22 05:36:25 base kernel: hub.c: new USB device 00:04.2-1.4, assigned address 3 Oct 22 05:36:26 base kernel: usb.c: USB device 3 (vend/prod 0x698/0x1786) is not claimed by any active driver. Oct 22 05:36:27 base kernel: Initializing USB Mass Storage driver... Oct 22 05:36:27 base kernel: usb.c: registered new driver usb-storage Oct 22 05:36:27 base kernel: USB Mass Storage support registered. Oct 22 05:36:27 base usb: Loading USB storage: succeeded Oct 22 05:36:28 base gpm[3243]: Connecting at fd 7 Oct 22 05:36:31 base /etc/hotplug/usb.agent: ... no modules for USB product 0/0/0 Oct 22 05:36:32 base /etc/hotplug/usb.agent: Setup hid for USB product 698/1786/1 Oct 22 05:36:32 base /etc/hotplug/usb.agent: ... no modules for USB product 698/9999/1 Oct 22 05:37:04 base kernel: hub.c: new USB device 00:04.2-1.2, assigned address 4 Oct 22 05:37:04 base kernel: hub.c: USB hub found Oct 22 05:37:04 base kernel: hub.c: 1 port detected Oct 22 05:37:04 base kernel: usb-uhci.c: interrupt, status 3, frame# 692 Oct 22 05:37:04 base kernel: hub.c: new USB device 00:04.2-1.2.1, assigned address 5 Oct 22 05:37:04 base kernel: scsi1 : SCSI emulation for USB Mass Storage devices Oct 22 05:37:04 base kernel: Vendor: Model: Rev: Oct 22 05:37:04 base kernel: Type: Direct-Access ANSI SCSI revision: 02 Oct 22 05:37:12 base /etc/hotplug/usb.agent: Setup usb-storage for USB product 67b/2317/1 Oct 22 05:37:12 base /etc/hotplug/usb.agent: ... no modules for USB product 67b/2315/1 >>> >>> >>Прошу прощения ^^^^^^^^^^^^^^^^^^ - оно там, что - само появится? :-0 >>Мне ничего делать не надо? >> >> В fstab ничего не появилось. >именно так, если устройство было обнаружено... отвечает за это, насколько я понимаю, hotplug. > > > > >>>/dev/sda1 /mnt/flash auto >>>noauto,user,kudzu,sync,noexec,nodev,nosuid,iocharset=koi8-r 0 0 >>> >>>затем говорим: >>> >>>mount /mnt/flash >>> >>> >>> >> И эта точка монтирования тоже - сама появится? >> >> > >так точно. > > Равно как и /mnt/flash - не появилось. А когда я вручную внес в fstab написанное, создал /mnt/fstab и отдал команду mount /mnt/flash, то получил в ответ: mount: you must specify filesystem type Заменив в fstab auto на usbdevfs и опять скомандовав mount /mnt/flash получил там что-то подмонтированное, но явно не имеющее отношения к файлам на флешке: # ls -R /mnt/flash /mnt/flash: 001 devices drivers /mnt/flash/001: 001 002 003 006 007 >>>и получаем доступ к файлам на флэшке. >>>причем драйв монтируется от имени того пользозователя, кто набрал эту >>>команду и права выставляются 700. >>> >>> >>> >>> >>> >>>> Мини-вариант (вопроса): собираюсь купить енту самую флэшку, >>>>договорился, предварительно, что смогу, если что, _быстро_ вернуть - а >>>>вот как ТОЧНО убедиться что работает, что совместимо со стоящей Линуксой? >>>> >>>> >>>> >>>> >>>сейчас практически все flash'ки работают через модуль usb-storage >>> >>> >>> >>> >><skip> >> >> Так что: мне не хватает еще какого-то модуля специфичного для именнно этого типа флешки? Если да - то откуда его брать? И для всех ли флешек он таки нужон? И (кстати) - почему вдруг заткнулся звук (по ходу сих манипуляций)? -- == В действительности все обстоит совершенно иначе чем на самом деле. == BR, Oleg N. Kayunov.
next prev parent reply other threads:[~2003-10-22 2:48 UTC|newest] Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top 2003-10-02 13:50 [Comm] " Dmitry Kovalsky 2003-10-02 14:20 ` Sergey Vlasov 2003-10-02 15:00 ` Dmitry Kovalsky 2003-10-02 15:14 ` Sergey Vlasov 2003-10-02 15:43 ` Dmitry Kovalsky 2003-10-02 18:54 ` Mikhail Arkhipov 2003-10-18 5:02 ` [Comm] " Oleg N. Kayunov 2003-10-18 7:19 ` Alexander Kubatkin 2003-10-18 9:42 ` [Comm] " Sergey S. Skulachenko 2003-10-19 19:53 ` [Comm] " Oleg N. Kayunov 2003-10-20 4:58 ` Alexander Kubatkin 2003-10-21 4:58 ` Oleg N. Kayunov 2003-10-21 5:00 ` Oleg N. Kayunov 2003-10-21 7:03 ` Alexander Kubatkin 2003-10-22 2:48 ` Oleg N. Kayunov [this message] 2003-10-22 5:29 ` Alexander Kubatkin 2003-10-22 7:56 ` Oleg N. Kayunov
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=3F95EFE6.9000902@mtu-net.ru \ --to=okayunov@mtu-net.ru \ --cc=community@altlinux.ru \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: link
ALT Linux Community general discussions This inbox may be cloned and mirrored by anyone: git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 community community/ http://lore.altlinux.org/community \ mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com public-inbox-index community Example config snippet for mirrors. Newsgroup available over NNTP: nntp://lore.altlinux.org/org.altlinux.lists.community AGPL code for this site: git clone https://public-inbox.org/public-inbox.git