Здравствуйте!
В сообщении от Tuesday 06 January 2009 19:57:40 Alexey I. Froloff написал(а):
> * Mike Shuvalov <shuvalov.mv@> [090106 19:49]:
> > ata1: SATA max UDMA/133 cmd 0xd000 ctl 0xd400 bmdma 0xe000 irq 19
>
> А что в dmesg про ata и sd в районе этой строчки?
>
> > Вроде как говорит что нет смысла для данного устройства. И, к стати,
> > вывод
>
> Покажите полный вывод hdparm -iI /dev/sda
>

/dev/sda:

 Model=ST3250310AS                             , FwRev=3.AAA   , SerialNo=            
5RY056JR
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=?16?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: Unspecified:  ATA/ATAPI-1,2,3,4,5,6,7

 * signifies the current active mode


ATA device, with non-removable media
	Model Number:       ST3250310AS                             
	Serial Number:      5RY056JR
	Firmware Revision:  3.AAA   
Standards:
	Supported: 7 6 5 4 
	Likely used: 7
Configuration:
	Logical		max	current
	cylinders	16383	16383
	heads		16	16
	sectors/track	63	63
	--
	CHS current addressable sectors:   16514064
	LBA    user addressable sectors:  268435455
	LBA48  user addressable sectors:  488395055
	device size with M = 1024*1024:      238474 MBytes
	device size with M = 1000*1000:      250058 MBytes (250 GB)
Capabilities:
	LBA, IORDY(can be disabled)
	Queue depth: 32
	Standby timer values: spec'd by Standard, no device specific minimum
	R/W multiple sector transfer: Max = 16	Current = 16
	Recommended acoustic management value: 208, current value: 0
	DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 
	     Cycle time: min=120ns recommended=120ns
	PIO: pio0 pio1 pio2 pio3 pio4 
	     Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
	Enabled	Supported:
	   *	SMART feature set
	    	Security Mode feature set
	   *	Power Management feature set
	   *	Write cache
	   *	Look-ahead
	   *	Host Protected Area feature set
	   *	WRITE_BUFFER command
	   *	READ_BUFFER command
	   *	DOWNLOAD_MICROCODE
	    	SET_MAX security extension
	   *	48-bit Address feature set
	   *	Device Configuration Overlay feature set
	   *	Mandatory FLUSH_CACHE
	   *	FLUSH_CACHE_EXT
	   *	SMART error logging
	   *	SMART self-test
	   *	General Purpose Logging feature set
	   *	SATA-I signaling speed (1.5Gb/s)
	   *	SATA-II signaling speed (3.0Gb/s)
	   *	Native Command Queueing (NCQ)
	   *	Phy event counters
	    	Device-initiated interface power management
	   *	Software settings preservation
Security: 
	Master password revision code = 65534
		supported
	not	enabled
	not	locked
		frozen
	not	expired: security count
	not	supported: enhanced erase
Checksum: correct

> В биосе что на счёт винтов выставлено?

Первым делом туда заглянул, но там особо ничего не выставишь :( 
Автоопределение и все :( (либо чего-то недосмотрел)

-- 
С уважением,
Михаил Шувалов