Re: [Comm] [sisyphus] desktop/server 4 + Asus X50 Vseries == ПРОЛЁТ ? :(

[Gleb Kulikov <glebus@asd.iao.ru>]

В сообщении от Вторник 31 июля 2007 Gleb Kulikov написал:

Коллеги,
я так понимаю, ничего не изменилось?

Ни 4.0.1, ни 4.0.2, ни 4.0.3 -- жёсткого диска "не видят". Мандрива (ещё 2007) 
-- работает без проблем.

> В сообщении от Вторник 31 июля 2007 Шишков Евгений написал:
> > Gleb Kulikov пишет:
> > > Джентельмены,
> > >
> > > я правильно понимаю, что ни 4, ни тем более, 3, инсталлировать на ноут
> > > ASUS X50VSeries, не получится?
> > >
> > > жёсткий диск отображается (меню биос - настройки жёсткого диска) на 3
> > > мастер, на 1-ом мастере, DVD.
> > >
> > > инталлятор, жёсткого диска не видит.
> > > Нет доступа к жёсткому диску, и при загрузке в лайв-сиди.
> >
> > Ну Вы распишите немного про него.
> > Точная модель (а не Series)?
> > Что за чипсет?
>
> Популярнейшие машинки бюджетной серии. Собственно, у нас на работе мужик
> принёс, и опс... пролёт.
>
> Кстати, звук не работает тоже (нет микшера, хотя модули альзы встают),
> набортная видеокамера, также себя никак не проявляет.
>
> модель X50V
> MB Ver. : F5V ID:2C
> 76N0AS066825
> CheckNumber6519
>
> CPU Inel T2130
>
> 00:00.0 Host bridge: Silicon Integrated Systems [SiS] Unknown device 0671
> 00:01.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
> 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media
> IO] (rev 01)
> 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev 01)
> 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller
> (rev 0f)
> 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller
> (rev 0f)
> 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
> 00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA Controller /
> IDE mode (rev 03)
> 00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
> 00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
> 00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> RTL-8139/8139C/8139C+ (rev 10)
> 00:0f.0 Audio device: Silicon Integrated Systems [SiS] Azalia Audio
> Controller 01:00.0 VGA compatible controller: ATI Technologies Inc Unknown
> device 718a 02:00.0 Ethernet controller: Atheros Communications, Inc.
> Unknown device 001c (rev 01)
>
> Linux version 2.6.18-std-smp-alt6 (builder@hint1.office.altlinux.org) (gcc
> version 4.1.1 20070105 (ALT Linux, build 4.1.1-alt11)) #1 SMP Sun Apr 29
> 00:41:18 MSD 2007
> BIOS-provided physical RAM map:
>  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
>  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
>  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
>  BIOS-e820: 0000000000100000 - 000000003ffb0000 (usable)
>  BIOS-e820: 000000003ffb0000 - 000000003ffbe000 (ACPI data)
>  BIOS-e820: 000000003ffbe000 - 0000000040000000 (ACPI NVS)
>  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
>  BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
> 127MB HIGHMEM available.
> 896MB LOWMEM available.
> On node 0 totalpages: 262064
>   DMA zone: 4096 pages, LIFO batch:0
>   Normal zone: 225280 pages, LIFO batch:31
>   HighMem zone: 32688 pages, LIFO batch:7
> DMI present.
> ACPI: RSDP (v000 ACPIAM                                ) @ 0x000f8db0
> ACPI: RSDT (v001 _ASUS_ Notebook 0x20070402 MSFT 0x00000097) @ 0x3ffb0000
> ACPI: FADT (v002 040207 FACP0939 0x20070402 MSFT 0x00000097) @ 0x3ffb0200
> ACPI: MADT (v001 040207 APIC0939 0x20070402 MSFT 0x00000097) @ 0x3ffb0390
> ACPI: MCFG (v001 040207 OEMMCFG  0x20070402 MSFT 0x00000097) @ 0x3ffb03f0
> ACPI: SLIC (v001 _ASUS_ Notebook 0x20070402 MSFT 0x00000097) @ 0x3ffb0430
> ACPI: WDRT (v001 040207 OEMWDRT  0x20070402 MSFT 0x00000097) @ 0x3ffb05b0
> ACPI: BOOT (v001 040207 BOOT0939 0x20070402 MSFT 0x00000097) @ 0x3ffb0600
> ACPI: OEMB (v001 040207 OEMB0939 0x20070402 MSFT 0x00000097) @ 0x3ffbe040
> ACPI: DSDT (v001  A0714 A0714002 0x00000002 INTL 0x20051117) @ 0x00000000
> ACPI: PM-Timer IO Port: 0x808
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> Processor #0 6:14 APIC version 20
> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
> Processor #1 6:14 APIC version 20
> ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 2, version 20, address 0xfec00000, GSI 0-23
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
> ACPI: IRQ0 used by override.
> ACPI: IRQ2 used by override.
> ACPI: IRQ9 used by override.
> Enabling APIC mode:  Flat.  Using 1 I/O APICs
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at 50000000 (gap: 40000000:bee00000)
> Detected 1866.276 MHz processor.
> Built 1 zonelists.  Total pages: 262064
> Kernel command line: BOOT_IMAGE=alt0/vmlinuz vga=0x314 lang=ru
> automatic=method:cdrom initrd=alt0/full.cz live fastboot stagename=live
> mapped APIC to ffffd000 (fee00000)
> mapped IOAPIC to ffffc000 (fec00000)
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Initializing CPU#0
> PID hash table entries: 4096 (order: 12, 16384 bytes)
> Console: colour dummy device 80x25
> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Memory: 1031660k/1048256k available (1585k kernel code, 15944k reserved,
> 640k data, 192k init, 130752k highmem)
> Checking if this processor honours the WP bit even in supervisor mode...
> Ok. Calibrating delay using timer specific routine.. 3734.39 BogoMIPS
> (lpj=7468787)
> Security Framework v1.0.0 initialized
> Capability LSM initialized
> Mount-cache hash table entries: 512
> CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000
> 0000c189 00000000 00000000
> CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000
> 0000c189 00000000 00000000
> monitor/mwait feature present.
> using mwait in idle threads.
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 1024K
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 0
> CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189
> 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> Compat vDSO mapped to ffffe000.
> Checking 'hlt' instruction... OK.
> SMP alternatives: switching to UP code
> checking if image is initramfs... it is
> Freeing initrd memory: 3753k freed
> ACPI: Core revision 20060707
> ACPI: Looking for DSDT in initramfs... /DSDT.aml does not exist.
> CPU0: Intel Genuine Intel(R) CPU           T2130  @ 1.86GHz stepping 0c
> SMP alternatives: switching to SMP code
> Booting processor 1/1 eip 3000
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 3732.57 BogoMIPS
> (lpj=7465147)
> CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000
> 0000c189 00000000 00000000
> CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000
> 0000c189 00000000 00000000
> monitor/mwait feature present.
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 1024K
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 1
> CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189
> 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#1.
> CPU1: Intel Genuine Intel(R) CPU           T2130  @ 1.86GHz stepping 0c
> Total of 2 processors activated (7466.96 BogoMIPS).
> ENABLING IO-APIC IRQs
> ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
> ..MP-BIOS bug: 8254 timer not connected to IO-APIC
> ...trying to set up timer (IRQ0) through the 8259A ...  failed.
> ...trying to set up timer as Virtual Wire IRQ... works.
> checking TSC synchronization across 2 CPUs: passed.
> Brought up 2 CPUs
> migration_cost=434
> NET: Registered protocol family 16
> ACPI: bus type pci registered
> PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
> PCI: Not using MMCONFIG.
> PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
> PCI: Using configuration type 1
> Setting up standard PCI resources
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PCI: Probing PCI hardware (bus 00)
> Boot video device is 0000:01:00.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: Embedded Controller [EC0] (gpe 25) interrupt mode.
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 *15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 *7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 7 10 11 12 14)
> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> pnp: PnP ACPI: found 11 devices
> PnPBIOS: Disabled by ACPI PNP
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
> report PCI: Bridge: 0000:00:01.0
>   IO window: a000-afff
>   MEM window: fa900000-fa9fffff
>   PREFETCH window: aff00000-bfefffff
> PCI: Bridge: 0000:00:06.0
>   IO window: disabled.
>   MEM window: faa00000-faafffff
>   PREFETCH window: disabled.
> PCI: Bridge: 0000:00:07.0
>   IO window: b000-cfff
>   MEM window: fab00000-feafffff
>   PREFETCH window: bff00000-dfefffff
> PCI: Setting latency timer of device 0000:00:01.0 to 64
> PCI: Setting latency timer of device 0000:00:06.0 to 64
> PCI: Setting latency timer of device 0000:00:07.0 to 64
> NET: Registered protocol family 2
> IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
> TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
> TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
> TCP: Hash tables configured (established 131072 bind 65536)
> TCP reno registered
> Simple Boot Flag value 0xc0 read from CMOS RAM was invalid
> Simple Boot Flag at 0xff set to 0x1
> audit: initializing netlink socket (disabled)
> audit(1185912994.772:1): initialized
> highmem bounce pool size: 64 pages
> Total HugeTLB memory allocated, 0
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> Initializing Cryptographic API
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> PCI: Setting latency timer of device 0000:00:01.0 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:01.0:pcie00]
> PCI: Setting latency timer of device 0000:00:06.0 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:06.0:pcie00]
> PCI: Setting latency timer of device 0000:00:07.0 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:07.0:pcie00]
> Allocate Port Service[0000:00:07.0:pcie02]
> vesafb: framebuffer at 0xb0000000, mapped to 0xf8880000, using 3750k, total
> 16384k
> vesafb: mode is 800x600x16, linelength=1600, pages=16
> vesafb: protected mode interface info at c000:aac2
> vesafb: pmi: set display start = c00cab4a, set palette = c00cac06
> vesafb: scrolling: redraw
> vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
> bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size
> 150058 bytes,<6>...found (800x600, 27802 bytes, v3).
> Console: switching to colour frame buffer device 97x34
> fb0: VESA VGA frame buffer device
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
> RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
> PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
> i8042.c: Detected active multiplexing controller, rev 1.1.
> serio: i8042 AUX0 port at 0x60,0x64 irq 12
> serio: i8042 AUX1 port at 0x60,0x64 irq 12
> serio: i8042 AUX2 port at 0x60,0x64 irq 12
> serio: i8042 AUX3 port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> mice: PS/2 mouse device common for all mice
> md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
> md: bitmap version 4.39
> TCP bic registered
> NET: Registered protocol family 1
> Using IPI No-Shortcut mode
> ACPI: (supports S0 S1 S3 S4 S5)
> Time: tsc clocksource has been installed.
> Freeing unused kernel memory: 192k freed
> Executing init=/init
> input: AT Translated Set 2 keyboard as /class/input/input0
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> ACPI: PCI Interrupt 0000:00:03.3[C] -> GSI 22 (level, low) -> IRQ 201
> ehci_hcd 0000:00:03.3: EHCI Host Controller
> ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:03.3: irq 201, io mem 0xfebfd000
> ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 8 ports detected
> usb 1-8: new high speed USB device using ehci_hcd and address 3
> usb 1-8: configuration #1 chosen from 1 choice
> ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
> ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 209
> ohci_hcd 0000:00:03.0: OHCI Host Controller
> ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
> ohci_hcd 0000:00:03.0: irq 209, io mem 0xfebff000
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 4 ports detected
> ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 217
> ohci_hcd 0000:00:03.1: OHCI Host Controller
> ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
> ohci_hcd 0000:00:03.1: irq 217, io mem 0xfebfe000
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 4 ports detected
> usb 3-2: new low speed USB device using ohci_hcd and address 2
> usb 3-2: configuration #1 chosen from 1 choice
> usbcore: registered new driver hiddev
> input: Logitech Logitech USB Optical Mouse as /class/input/input1
> input: USB HID v1.11 Mouse [Logitech Logitech USB Optical Mouse] on
> usb-0000:00:03.1-2
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.6:USB HID core driver
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> SCSI subsystem initialized
> SIS5513: IDE controller at PCI slot 0000:00:02.5
> SIS5513: chipset revision 1
> SIS5513: not 100% native mode: will probe irqs later
> SIS5513: SiS968 ATA 133 (2nd gen) controller
>     ide0: BM-DMA at 0xffe0-0xffe7, BIOS settings: hda:DMA, hdb:DMA
> Probing IDE interface ide0...
> hda: MATSHITADVD-RAM UJ-850S, ATAPI CD/DVD-ROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hda: ATAPI 63X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.20
> Probing IDE interface ide1...
> usbcore: registered new driver libusual
> Initializing USB Mass Storage driver...
> scsi0 : SCSI emulation for USB Mass Storage devices
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usb-storage: device found at 3
> usb-storage: waiting for device to settle before scanning
>   Vendor: Generic-  Model: xD/SDMMC/MS/Pro   Rev: 1.00
>   Type:   Direct-Access                      ANSI SCSI revision: 00
> usb-storage: device scan complete
> ISO 9660 Extensions: Microsoft Joliet Level 3
> ISO 9660 Extensions: RRIP_1991A
> loop: loaded (max 8 devices)
> squashfs: version 3.2 (2007/01/02) Phillip Lougher
> Real Time Clock Driver v1.12ac
> input: PC Speaker as /class/input/input2
> sd 0:0:0:0: Attached scsi removable disk sda
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> ts: Compaq touchscreen protocol output
> Linux agpgart interface v0.101 (c) Dave Jones
> ath_hal: module license 'Proprietary' taints kernel.
> ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
> 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
> 8139cp 0000:00:0d.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible
> chip
> 8139cp 0000:00:0d.0: Try the "8139too" driver instead.
> wlan: 0.8.4.2 (0.9.3.1)
> 8139too Fast Ethernet driver 0.9.27
> ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 17 (level, low) -> IRQ 225
> eth0: RealTek RTL8139 at 0xf8822c00, 00:1b:fc:48:37:09, IRQ 225
> eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
> ath_pci: 0.9.4.5 (0.9.3.1)
> ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 233
> PCI: Setting latency timer of device 0000:02:00.0 to 64
> ath_rate_sample: 1.2 (0.9.3.1)
> wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
> wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps
> 24Mbps 36Mbps 48Mbps 54Mbps
> wifi0: H/W encryption support: WEP AES AES_CCM TKIP
> wifi0: mac 10.0 phy 6.1 radio 10.2
> wifi0: Use hw queue 1 for WME_AC_BE traffic
> wifi0: Use hw queue 0 for WME_AC_BK traffic
> wifi0: Use hw queue 2 for WME_AC_VI traffic
> wifi0: Use hw queue 3 for WME_AC_VO traffic
> wifi0: Use hw queue 8 for CAB traffic
> wifi0: Use hw queue 9 for beacons
> Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
> wifi0: Atheros 5424/2424: mem=0xfaaf0000, irq=233
> ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 18 (level, low) -> IRQ 50
> PCI: Setting latency timer of device 0000:00:0f.0 to 64
> input: SynPS/2 Synaptics TouchPad as /class/input/input3
> hda_codec: Unknown model for ALC861, trying auto-probe from BIOS...
> Registering unionfs 1.4
> unionfs: debugging is not enabled
> device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
> dm-devel@redhat.com
> [fglrx] Maximum main memory to use for locked dma buffers: 929 MBytes.
> [fglrx] module loaded - fglrx 8.36.5 [Apr 17 2007] on minor 0
> ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 233
> [fglrx] total      GART = 130023424
> [fglrx] free       GART = 114032640
> [fglrx] max single GART = 114032640
> [fglrx] total      LFB  = 66977792
> [fglrx] free       LFB  = 52588544
> [fglrx] max single LFB  = 52588544
> [fglrx] total      Inv  = 0
> [fglrx] free       Inv  = 0
> [fglrx] max single Inv  = 0
> [fglrx] total      TIM  = 0
> ACPI: AC Adapter [AC0] (on-line)
> QEMU Accelerator Module version 1.3.0, Copyright (c) 2005-2007 Fabrice
> Bellard KQEMU installed, max_locked_mem=517936kB.
> bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size
> 150058 bytes,<6>...found (800x600, 27802 bytes, v3).
> bootsplash: status on console 1 changed to on
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> hda_codec: num_steps = 0 for NID=0x8
> usb 1-1: new high speed USB device using ehci_hcd and address 4
> usb 1-1: configuration #1 chosen from 1 choice
> scsi1 : SCSI emulation for USB Mass Storage devices
> usb-storage: device found at 4
> usb-storage: waiting for device to settle before scanning
>   Vendor: USB       Model: FLASH DISK        Rev: 2.00
>   Type:   Direct-Access                      ANSI SCSI revision: 02
> ready
> SCSI device sdb: 256000 512-byte hdwr sectors (131 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 03 00 00 00
> sdb: assuming drive cache: write through
> SCSI device sdb: 256000 512-byte hdwr sectors (131 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 03 00 00 00
> sdb: assuming drive cache: write through
>  sdb: sdb1 sdb2
> sd 1:0:0:0: Attached scsi removable disk sdb
> sd 1:0:0:0: Attached scsi generic sg1 type 0
> usb-storage: device scan complete
> EXT2-fs warning: mounting fs with errors, running e2fsck is recommended
> EXT2-fs error (device sdb2): ext2_check_page: bad entry in directory #2:
> unaligned directory entry - offset=0, inode=4294967295, rec_len=65535,
> name_len=255
> EXT2-fs error (device sdb2): ext2_readdir: bad page in #2

> Я так понимаю, что диски и разделы видны. но почему-то :

Не альтом! Это вывод, сделанный из-под Мандривы.

> >SIS5513: not 100% native mode: will probe irqs later
> >SIS5513: SiS968 ATA 133 (2nd gen) controller

Хихин Руслан:

>А интересно посмотреть dmesg под Альтом, хотя "ядерщикам" и так всё 
>прозрачно. 
>Я-бы повесил багу с dmesg и lsmod под Alt и под Мандривой.

Лепихов:

>ясно. попробую добавить поддержку этого недо-sata контроллера в наше ядро.



-- 
      Салют, /GLeb

UIN: 15341920
jabber://gleb@asd.iao.ru
sip://2387245@sipnet.ru			(telephony)
skype://gleb_kulikov.tomsk		(telephony)
sip://20000204@sip.pctel.ru		(telephony)
netmail: 2:5005/78