* Re: [Comm] ALD4 Проблема с Eth0
2007-09-26 18:33 ` Michael Shigorin
@ 2007-09-27 16:34 ` Mike Shuvalov
2007-10-05 17:28 ` Michael Shigorin
0 siblings, 1 reply; 4+ messages in thread
From: Mike Shuvalov @ 2007-09-27 16:34 UTC (permalink / raw)
To: shigorin, ALT Linux Community general discussions
Michael Shigorin пишет:
> On Wed, Sep 26, 2007 at 10:20:20PM +0400, Mike Shuvalov wrote:
>> Обновил систему и появились тормоза на eth0. Пинги до соседней
>> машины принимают фантастические значения:
>> Что где нужно подкрутить, что бы вылечить это дело?
>
> Покажите dmesg и /proc/interrupts? (возможно, поможет загрузка
> с pci=noacpi или заклинания из той же оперы)
>
Вот вывод dmesg:
==============================
Linux version 2.6.18-std-smp-alt8 (builder@hint1.office.altlinux.org)
(gcc version 4.1.1 20070105 (ALT Linux, build 4.1.1-alt11)) #1 SMP Mon
Sep 24 01:41:06 MSD 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f4cb0
On node 0 totalpages: 262128
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32752 pages, LIFO batch:7
DMI 2.4 present.
ACPI: RSDP (v000 GBT ) @ 0x000f6620
ACPI: RSDT (v001 GBT GBTUACPI 0x42302e31 GBTU 0x01010101) @ 0x3fff3040
ACPI: FADT (v001 GBT GBTUACPI 0x42302e31 GBTU 0x01010101) @ 0x3fff30c0
ACPI: HPET (v001 GBT GBTUACPI 0x42302e31 GBTU 0x00000098) @ 0x3fff69c0
ACPI: MCFG (v001 GBT GBTUACPI 0x42302e31 GBTU 0x01010101) @ 0x3fff6a40
ACPI: MADT (v001 GBT GBTUACPI 0x42302e31 GBTU 0x01010101) @ 0x3fff6900
ACPI: SSDT (v001 PmRef Cpu0Ist 0x00003000 INTL 0x20040311) @ 0x3fff6ac0
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20040311) @ 0x3fff6f50
ACPI: DSDT (v001 GBT GBTUACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:b0000000)
Detected 1607.787 MHz processor.
Built 1 zonelists. Total pages: 262128
Kernel command line: auto BOOT_IMAGE=ALTLinux ro
root=UUID=493b63ac-d971-4eb8-80d7-70158beeb5ff panic=30 splash=silent
resume=/dev/sdb2
bootsplash: silent mode.
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1035208k/1048512k available (1585k kernel code, 12732k reserved,
640k data, 192k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3218.20 BogoMIPS
(lpj=6436408)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
0000e39d 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000
0000e39d 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0000e39d
00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
checking if image is initramfs... it is
Freeing initrd memory: 541k freed
ACPI: Core revision 20060707
ACPI: Looking for DSDT in initramfs... /DSDT.aml does not exist.
CPU0: Intel Genuine Intel(R) CPU 2140 @ 1.60GHz stepping 02
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3215.72 BogoMIPS
(lpj=6431440)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
0000e39d 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000
0000e39d 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0000e39d
00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU 2140 @ 1.60GHz stepping 02
Total of 2 processors activated (6433.92 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=63
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
pnp: 00:0a: ioport range 0x400-0x4bf could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: 9000-9fff
MEM window: e0000000-e3ffffff
PREFETCH window: d0000000-dfffffff
PCI: Bridge: 0000:00:1c.0
IO window: 8000-8fff
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
IO window: a000-afff
MEM window: e4000000-e5ffffff
PREFETCH window: 50000000-500fffff
PCI: Bridge: 0000:00:1e.0
IO window: 7000-7fff
MEM window: disabled.
PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1190919823.620:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
Allocate Port Service[0000:00:1c.3:pcie03]
vesafb: framebuffer at 0xe1000000, mapped to 0xf8880000, using 10240k,
total 14336k
vesafb: mode is 1280x1024x16, linelength=2560, pages=1
vesafb: protected mode interface info at c000:ad80
vesafb: pmi: set display start = c00cade3, set palette = c00cae3e
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce
3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size
127900 bytes,<6> error in silent jpeg.
...found (1280x1024, 22880 bytes, v3).
Console: switching to colour frame buffer device 157x60
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
NET: Registered protocol family 1
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 192k freed
Executing init=/init
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 217
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: Optiarc DVD RW AD-5170A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
SCSI subsystem initialized
libata version 2.00 loaded.
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xD000 ctl 0xD402 bmdma 0xE000 irq 177
ata2: SATA max UDMA/133 cmd 0xD800 ctl 0xDC02 bmdma 0xE008 irq 177
scsi0 : ata_piix
ata1.00: ATA-7, max UDMA/133, 488395055 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.01: ATA-7, max UDMA7, 156301488 sectors: LBA48 NCQ (depth 0/32)
ata1.01: ata1: dev 1 multi count 16
ata1.00: configured for UDMA/133
ata1.01: configured for UDMA/133
scsi1 : ata_piix
ATA: abnormal status 0x7F on port 0xD807
Vendor: ATA Model: ST3250310AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 488395055 512-byte hdwr sectors (250058 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 488395055 512-byte hdwr sectors (250058 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
Vendor: ATA Model: SAMSUNG HD080HJ Rev: ZH10
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb4 < sdb5 >
sd 0:0:1:0: Attached scsi disk sdb
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 225, io mem 0xe6004000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 177
hda: ATAPI 126X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 945G Chipset.
agpgart: AGP aperture is 256M @ 0x0
intel_rng: FWH not detected
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.11 Wed Jun 13
18:21:22 PDT 2007
input: PC Speaker as /class/input/input1
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [
Cpu1Ist] [20060707]
ACPI: Processor [CPU1] (supports 2 throttling states)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:03:00.0 to 64
eth0: Identified chip type is 'RTL8168B/8111B'.
eth0: r10001.05, the Linux device driver for Realtek Ethernet
Controllers at 0xa000, 00:1a:4d:20:d8:ae, IRQ 177
Realtek RTL8168/8111 Family PCI-E Gigabit Ethernet Network Adapter
Driver version:1.05
Released date:2006/10/25
Link Status:Linked
Link Speed:100Mbps
Duplex mode:Full-Duplex
I/O Base:0xA000(I/O port)
IRQ:177
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1b.0 to 64
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 225, io base 0x0000b000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 177, io base 0x0000b400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 217, io base 0x0000b800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 169, io base 0x0000bc00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 4-1: new low speed USB device using uhci_hcd and address 2
usb 4-1: configuration #1 chosen from 1 choice
usb 4-2: new low speed USB device using uhci_hcd and address 3
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: Attached scsi generic sg1 type 0
usb 4-2: configuration #1 chosen from 1 choice
usb 5-1: new full speed USB device using uhci_hcd and address 2
Real Time Clock Driver v1.12ac
usb 5-1: configuration #1 chosen from 1 choice
Floppy drive(s): fd0 is 1.44M
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
FDC 0 is a post-1991 82077
usb 5-2: new full speed USB device using uhci_hcd and address 3
usb 5-2: configuration #1 chosen from 1 choice
hub 5-2:1.0: USB hub found
hub 5-2:1.0: 3 ports detected
usb 5-2.1: new full speed USB device using uhci_hcd and address 4
usb 5-2.1: configuration #1 chosen from 1 choice
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.9
usb 5-2.2: new full speed USB device using uhci_hcd and address 5
usb 5-2.2: configuration #1 chosen from 1 choice
usb 5-2.3: new full speed USB device using uhci_hcd and address 6
usb 5-2.3: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
usbcore: registered new driver hci_usb
input: Genius NetScroll + Traveler as /class/input/input2
input: USB HID v1.10 Mouse [Genius NetScroll + Traveler] on
usb-0000:00:1d.2-1
input: Padix Co. Ltd. USB, 3-axis, 4-button joystick as /class/input/input3
input: USB HID v1.00 Joystick [Padix Co. Ltd. USB, 3-axis, 4-button
joystick] on usb-0000:00:1d.2-2
input: Broadcom Corp BCM92045DG-Flash_UHE as /class/input/input4
input: USB HID v1.11 Keyboard [Broadcom Corp BCM92045DG-Flash_UHE] on
usb-0000:00:1d.3-2.2
input: Broadcom Corp BCM92045DG-Flash_UHE as /class/input/input5
input: USB HID v1.11 Mouse [Broadcom Corp BCM92045DG-Flash_UHE] on
usb-0000:00:1d.3-2.3
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ts: Compaq touchscreen protocol output
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Adding 3140696k swap on /dev/sdb2. Priority:-1 extents:1 across:3140696k
EXT3 FS on sdb1, internal journal
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.7)
UDF-fs: No VRS found
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
intel_rng: FWH not detected
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size
127900 bytes,<6> error in silent jpeg.
...found (1280x1024, 22880 bytes, v3).
bootsplash: status on console 1 changed to on
=============================================================================
вот содержимое /proc/interrupts
=============================================================================
CPU0 CPU1
0: 1338224 0 IO-APIC-edge timer
1: 3689 0 IO-APIC-edge i8042
6: 3 0 IO-APIC-edge floppy
7: 0 0 IO-APIC-edge parport0
8: 1 0 IO-APIC-edge rtc
9: 1 0 IO-APIC-level acpi
14: 138 0 IO-APIC-edge ide0
169: 1143915 0 IO-APIC-level HDA Intel, uhci_hcd:usb5, nvidia
177: 30567 0 IO-APIC-level libata, uhci_hcd:usb3, eth0
217: 40375 0 IO-APIC-level uhci_hcd:usb4
225: 5 0 IO-APIC-level ehci_hcd:usb1, uhci_hcd:usb2
NMI: 0 0
LOC: 1323421 1323438
ERR: 0
MIS: 0
=============================================================================
--
Mike Shuvalov
^ permalink raw reply [flat|nested] 4+ messages in thread