Здравствуйте Andrei Lomov В сообщении от 9 сентября 2006 08:06 Andrei Lomov написал(a): > Подскажите, пожалуйста, как проблему побороть. > > > > Есть машина, включенная в сеть по eth1, > > на ней еще две карты eth0, eth2, по которым подключены > > две машины из локалки: > > > > [andrei@main andrei]$ /sbin/ifconfig > > eth0 Link encap:Ethernet HWaddr 00:05:5D:81:2D:65 > > inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 > > UP BROADCAST MULTICAST MTU:1500 Metric:1 > > RX packets:202599 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:251181 errors:0 dropped:0 overruns:0 carrier:0 > > collisions:0 txqueuelen:1000 > > RX bytes:23403936 (22.3 Mb) TX bytes:135303304 (129.0 Mb) > > Interrupt:10 Base address:0xc000 > > > > eth1 Link encap:Ethernet HWaddr 00:05:5D:81:2D:66 > > inet addr:172.22.60.13 Bcast:172.22.60.127 > Mask:255.255.255.128 > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > RX packets:3128 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:19101 errors:0 dropped:0 overruns:0 carrier:0 > > collisions:0 txqueuelen:1000 > > RX bytes:3021687 (2.8 Mb) TX bytes:939141 (917.1 Kb) > > Interrupt:11 Base address:0xc400 > > > > eth2 Link encap:Ethernet HWaddr 00:11:95:F5:2B:69 > > inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > RX packets:845 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 > > collisions:0 txqueuelen:1000 > > RX bytes:83557 (81.5 Kb) TX bytes:630 (630.0 b) > > Interrupt:5 Base address:0xc800 > > > > lo Link encap:Local Loopback > > inet addr:127.0.0.1 Mask:255.0.0.0 > > UP LOOPBACK RUNNING MTU:16436 Metric:1 > > RX packets:1104 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:1104 errors:0 dropped:0 overruns:0 carrier:0 > > collisions:0 txqueuelen:0 > > RX bytes:123651 (120.7 Kb) TX bytes:123651 (120.7 Kb) > > > > > > > > Подключаю машину кабелем к eth0, все работает. > > > > Тот же кабель перебрасываю на eth2 -- нет пинга. > > > > Лампочка на eth2 моргает. > > > > Что-то не пойму, в чем может быть проблема... > > > > В messages вроде все нормально ?: > > ... > > eth0: VIA VT6105 Rhine-III at 0xc000, 00:05:5d:81:2d:65, IRQ 10. > > eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 > Link 0000. > > eth1: VIA VT6105 Rhine-III at 0xc400, 00:05:5d:81:2d:66, IRQ 11. > > eth1: MII PHY found at address 1, status 0x7869 advertising 05e1 > Link 41e1. > > eth2: VIA VT6105 Rhine-III at 0xc800, 00:11:95:f5:2b:69, IRQ 5. > > eth2: MII PHY found at address 1, status 0x7849 advertising 05e1 > Link 0000. > > eth1: Setting full-duplex based on MII #1 link partner capability of > 41e1. > > ... > > eth0: Setting full-duplex based on MII #1 link partner capability of > 45e1. > > eth0: Setting half-duplex based on MII #1 link partner capability of > 0000. > > eth2: Setting full-duplex based on MII #1 link partner capability of > 45e1. > > eth2: Setting half-duplex based on MII #1 link partner capability of > 0000. > > eth2: Setting full-duplex based on MII #1 link partner capability of > 45e1. > > eth0: Setting full-duplex based on MII #1 link partner capability of > 45e1. > > eth2: Setting half-duplex based on MII #1 link partner capability of > 0000. > > ... Вы говорите, что у вас 2 карты, а я вижу, что у вас подняты 3 интерфейса, причём IP адрес eth0 и eth2 совпадают, из-за этого совпадения у вас и проблемы. -- А ещё говорят так (fortune): > Может ну его нафиг, и собрать wireless-28pre3 ? Вам виднее, вы мантейнер. -- pilot in devel@ ________________________________________________________________________ С уважением Хихин Руслан (hihin@rambler.ru)