From: "Хихин Руслан" <hihin@rambler.ru>
To: community@lists.altlinux.org
Subject: Re: [Comm] eth0, eth1, eth2
Date: Sat, 9 Sep 2006 08:42:06 +0400
Message-ID: <200609090842.20489@ruslandh> (raw)
In-Reply-To: <edtejj$s0g$1@sea.gmane.org>
[-- Attachment #1: Type: text/plain, Size: 4301 bytes --]
Здравствуйте Andrei Lomov
В сообщении от 9 сентября 2006 08:06 Andrei Lomov написал(a):
> Подскажите, пожалуйста, как проблему побороть.
>
>
>
> Есть машина, включенная в сеть по eth1,
>
> на ней еще две карты eth0, eth2, по которым подключены
>
> две машины из локалки:
>
>
>
> [andrei@main andrei]$ /sbin/ifconfig
>
> eth0 Link encap:Ethernet HWaddr 00:05:5D:81:2D:65
>
> inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0
>
> UP BROADCAST MULTICAST MTU:1500 Metric:1
>
> RX packets:202599 errors:0 dropped:0 overruns:0 frame:0
>
> TX packets:251181 errors:0 dropped:0 overruns:0 carrier:0
>
> collisions:0 txqueuelen:1000
>
> RX bytes:23403936 (22.3 Mb) TX bytes:135303304 (129.0 Mb)
>
> Interrupt:10 Base address:0xc000
>
>
>
> eth1 Link encap:Ethernet HWaddr 00:05:5D:81:2D:66
>
> inet addr:172.22.60.13 Bcast:172.22.60.127
> Mask:255.255.255.128
>
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>
> RX packets:3128 errors:0 dropped:0 overruns:0 frame:0
>
> TX packets:19101 errors:0 dropped:0 overruns:0 carrier:0
>
> collisions:0 txqueuelen:1000
>
> RX bytes:3021687 (2.8 Mb) TX bytes:939141 (917.1 Kb)
>
> Interrupt:11 Base address:0xc400
>
>
>
> eth2 Link encap:Ethernet HWaddr 00:11:95:F5:2B:69
>
> inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0
>
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>
> RX packets:845 errors:0 dropped:0 overruns:0 frame:0
>
> TX packets:15 errors:0 dropped:0 overruns:0 carrier:0
>
> collisions:0 txqueuelen:1000
>
> RX bytes:83557 (81.5 Kb) TX bytes:630 (630.0 b)
>
> Interrupt:5 Base address:0xc800
>
>
>
> lo Link encap:Local Loopback
>
> inet addr:127.0.0.1 Mask:255.0.0.0
>
> UP LOOPBACK RUNNING MTU:16436 Metric:1
>
> RX packets:1104 errors:0 dropped:0 overruns:0 frame:0
>
> TX packets:1104 errors:0 dropped:0 overruns:0 carrier:0
>
> collisions:0 txqueuelen:0
>
> RX bytes:123651 (120.7 Kb) TX bytes:123651 (120.7 Kb)
>
>
>
>
>
>
>
> Подключаю машину кабелем к eth0, все работает.
>
>
>
> Тот же кабель перебрасываю на eth2 -- нет пинга.
>
>
>
> Лампочка на eth2 моргает.
>
>
>
> Что-то не пойму, в чем может быть проблема...
>
>
>
> В messages вроде все нормально ?:
>
> ...
>
> eth0: VIA VT6105 Rhine-III at 0xc000, 00:05:5d:81:2d:65, IRQ 10.
>
> eth0: MII PHY found at address 1, status 0x7849 advertising 05e1
> Link 0000.
>
> eth1: VIA VT6105 Rhine-III at 0xc400, 00:05:5d:81:2d:66, IRQ 11.
>
> eth1: MII PHY found at address 1, status 0x7869 advertising 05e1
> Link 41e1.
>
> eth2: VIA VT6105 Rhine-III at 0xc800, 00:11:95:f5:2b:69, IRQ 5.
>
> eth2: MII PHY found at address 1, status 0x7849 advertising 05e1
> Link 0000.
>
> eth1: Setting full-duplex based on MII #1 link partner capability of
> 41e1.
>
> ...
>
> eth0: Setting full-duplex based on MII #1 link partner capability of
> 45e1.
>
> eth0: Setting half-duplex based on MII #1 link partner capability of
> 0000.
>
> eth2: Setting full-duplex based on MII #1 link partner capability of
> 45e1.
>
> eth2: Setting half-duplex based on MII #1 link partner capability of
> 0000.
>
> eth2: Setting full-duplex based on MII #1 link partner capability of
> 45e1.
>
> eth0: Setting full-duplex based on MII #1 link partner capability of
> 45e1.
>
> eth2: Setting half-duplex based on MII #1 link partner capability of
> 0000.
>
> ...
Вы говорите, что у вас 2 карты, а я вижу, что у вас подняты 3
интерфейса, причём IP адрес eth0 и eth2 совпадают, из-за этого
совпадения у вас и проблемы.
--
А ещё говорят так (fortune):
> Может ну его нафиг, и собрать wireless-28pre3 ?
Вам виднее, вы мантейнер.
-- pilot in devel@
________________________________________________________________________
С уважением Хихин Руслан (hihin@rambler.ru)
[-- Attachment #2: Type: application/pgp-signature, Size: 189 bytes --]
next prev parent reply other threads:[~2006-09-09 4:42 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-09-09 4:06 Andrei Lomov
2006-09-09 4:42 ` Хихин Руслан [this message]
2006-09-09 13:59 ` Andrei Lomov
2006-09-09 14:05 ` Michael Shigorin
2006-09-09 16:21 ` Andrei Lomov
2006-09-09 16:25 ` Michael Shigorin
2006-09-09 16:48 ` Вадим Илларионов
2006-09-09 17:24 ` Хихин Руслан
2006-09-11 17:24 ` Andrei Lomov
2006-09-12 6:21 ` Шенцев Алексей Владимирович
2006-09-11 12:37 ` [Comm] [OBORONA-SPAM] " ABATAPA
2006-09-09 14:06 ` [Comm] " Sergei Boudnik
2006-09-11 11:27 ` Andrii Dobrovol`s`kii
2006-09-09 13:50 ` Michael Shigorin
2006-09-09 15:34 ` Andrei Lomov
2006-09-09 16:22 ` Michael Shigorin
2006-09-09 14:10 ` Sergey Vlasov
2006-09-09 17:12 ` Evgenii Terechkov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200609090842.20489@ruslandh \
--to=hihin@rambler.ru \
--cc=community@lists.altlinux.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
ALT Linux Community general discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
public-inbox-index community
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.community
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git