Re: [Comm] Pentax Optio 555

[Topper <xpyctman@rambler.ru>]

Sat, 19 Jun 2004 20:53:53 +0400 товарищь Sergey Vlasov писал(а):

SV> С каким ядром пробовали?
SV> 
SV> Покажите содержимое /proc/bus/usb/devices при подключенной камере, а
SV> также сообщения, появляющиеся в выводе dmesg после подключения.
SV> 

[root@Topper root]# dmesg |less
Linux version 2.4.25-std-up-alt4
==========skipped==============
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 17:46:28 Apr 13 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1f.2 to 64
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1f.4 to 64
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 23
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
==========skipped==============
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi1 : SCSI emulation for USB Mass Storage devices
  Vendor: PENTAX    Model: DIGITAL_CAMERA    Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sda: 1000448 512-byte hdwr sectors (512 MB)
sda: Write Protect is off
 sda: sda1

по идее, она должна монтироваться как флешка с использованием масс
сторожа, ибо он ее явно определяет. однако почему-то не монтируется.
точнее, монтируется, но содержимое карточки не отображает...

[root@Topper root]# cat /proc/bus/usb/devices 
T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 0.00
S:  Product=USB UHCI Root Hub
S:  SerialNumber=d800
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   8 Ivl=255ms
T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0a17 ProdID=000a Rev= 1.00
S:  Manufacturer=PENTAX
S:  Product=PENTAX OPTIO 555
S:  SerialNumber=000008606203
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Driver=usb-storage E:  Ad=04(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 0.00
S:  Product=USB UHCI Root Hub
S:  SerialNumber=d000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   8 Ivl=255ms



-- 
Всем спасибо, все свободны
ALT Linux Sisyphus 
Tualatin-1400@1650/384/FX5900XT
Registered Linux User #339833