* [Comm] OpenLDAP
@ 2003-12-01 13:02 Epiphanov Sergei
2003-12-01 22:53 ` Dmitry Lebkov
0 siblings, 1 reply; 2+ messages in thread
From: Epiphanov Sergei @ 2003-12-01 13:02 UTC (permalink / raw)
To: Рассылка Community
Всем привет.
Поставил OpenLDAP, настроил acl, создал базу. А тут потребовалось изменить
некоторые acl, однако при включени их или изменении в
/etc/openldap/slapd.conf ничего не происходит. Я имею в виду доступ к базе.
Например, вначале стояло
access to attr=uid
by self write
by anonymous auth
Изменил:
access to attr=uid
by self write
by * read
Так и должно быть и как разрулить в таком случае? Делать дамп базы, удалять
базу, править acl, после чего обратно загонять дамп в базу?
Заранее спасибо.
--
С уважением, Епифанов Сергей
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [Comm] OpenLDAP
2003-12-01 13:02 [Comm] OpenLDAP Epiphanov Sergei
@ 2003-12-01 22:53 ` Dmitry Lebkov
0 siblings, 0 replies; 2+ messages in thread
From: Dmitry Lebkov @ 2003-12-01 22:53 UTC (permalink / raw)
To: community
On Mon, 1 Dec 2003 16:02:45 +0300
Epiphanov Sergei <serpiph@entek.ru> wrote:
> Всем привет.
>
> Поставил OpenLDAP, настроил acl, создал базу. А тут потребовалось изменить
> некоторые acl, однако при включени их или изменении в
> /etc/openldap/slapd.conf ничего не происходит. Я имею в виду доступ к базе.
> Например, вначале стояло
> access to attr=uid
> by self write
> by anonymous auth
>
> Изменил:
> access to attr=uid
> by self write
> by * read
>
> Так и должно быть и как разрулить в таком случае?
> Делать дамп базы, удалять
> базу, править acl, после чего обратно загонять дамп в базу?
Это всё - лишнее. Достаточно 'service slapd restart'. ACL'и живут
только в конфиге.
--
WBR, Dmitry Lebkov
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2003-12-01 22:53 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2003-12-01 13:02 [Comm] OpenLDAP Epiphanov Sergei
2003-12-01 22:53 ` Dmitry Lebkov
ALT Linux Community general discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
public-inbox-index community
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.community
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git