* [Comm] скорость raid 5 @ 2003-09-29 8:53 Alexey Berezkin 2003-09-29 17:00 ` [Comm] " Konstantin Lepikhov 0 siblings, 1 reply; 6+ messages in thread From: Alexey Berezkin @ 2003-09-29 8:53 UTC (permalink / raw) To: community [-- Attachment #1: Type: text/plain, Size: 507 bytes --] Hello community, Есть железяка, gateway 8200 с контролером aic7890 и ami megaraid. 4 диска segate cheetah в raid 5. Как я понимаю непрерывный трансфер должен быть порядка 40-50Мb/s. Хотя hdparm дает следующее: #hdparm -tT /dev/sda /dev/sda: Timing buffer-cache reads: 492 MB in 2.00 seconds = 246.00 MB/sec Timing buffered disk reads: 26 MB in 3.16 seconds = 8.23 MB/sec Помогите разобраться с этой проблемой, или наставте на путь истинный. P.S. Кусок dmesg в атаче. -- Best regards, Alexey [-- Attachment #2: dmesg. --] [-- Type: application/octet-stream, Size: 2118 bytes --] ^ permalink raw reply [flat|nested] 6+ messages in thread
* [Comm] Re: скорость raid 5 2003-09-29 8:53 [Comm] скорость raid 5 Alexey Berezkin @ 2003-09-29 17:00 ` Konstantin Lepikhov 2003-09-30 7:21 ` Alexey Berezkin 0 siblings, 1 reply; 6+ messages in thread From: Konstantin Lepikhov @ 2003-09-29 17:00 UTC (permalink / raw) To: community Hi Alexey! Monday 29, at 11:53:43 AM you wrote: > Hello community, > > Есть железяка, gateway 8200 с контролером aic7890 и ami megaraid. 4 > диска segate cheetah в raid 5. Как я понимаю непрерывный трансфер > должен быть порядка 40-50Мb/s. Хотя hdparm дает следующее: > #hdparm -tT /dev/sda > > /dev/sda: > Timing buffer-cache reads: 492 MB in 2.00 seconds = 246.00 MB/sec > Timing buffered disk reads: 26 MB in 3.16 seconds = 8.23 MB/sec > > Помогите разобраться с этой проблемой, или наставте на путь истинный. > P.S. Кусок dmesg в атаче. irq conflict? Плохая терминация? Какой размер кеша на megaraid? например, с MegaRAID Elite 1600 след. картина: root@cedar ~# hdparm -tT /dev/sda /dev/sda: Timing buffer-cache reads: 864 MB in 2.00 seconds = 432.00 MB/sec Timing buffered disk reads: 186 MB in 3.01 seconds = 61.79 MB/sec root@cedar ~# root@cedar ~# cat /proc/megaraid/0/config MegaRAID Elite 1600 Controller Type: 438/466/467/471/493 Controller Supports 40 Logical Drives Controller / Driver uses 64 bit memory addressing Base = f8825000, Irq = 21, Logical Drives = 1, Channels = 2 Version =G170:F316, DRAM = 128Mb Controller Queue Depth = 254, Driver Queue Depth = 126 правда у меня raid10 -- WBR, Konstantin chat with ==>ICQ: 109916175 Lepikhov, speak to ==>JID: lakostis@jabber.org aka L.A. Kostis write to ==>mailto:lakostis@pisem.net.nospam ...The information is like the bank... (c) EC8OR ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Comm] Re: скорость raid 5 2003-09-29 17:00 ` [Comm] " Konstantin Lepikhov @ 2003-09-30 7:21 ` Alexey Berezkin 2003-09-30 19:03 ` Konstantin Lepikhov 0 siblings, 1 reply; 6+ messages in thread From: Alexey Berezkin @ 2003-09-30 7:21 UTC (permalink / raw) To: Konstantin Lepikhov Hello Konstantin, Monday, September 29, 2003, 8:00:10 PM, you wrote: KL> Hi Alexey! KL> Monday 29, at 11:53:43 AM you wrote: >> Hello community, >> >> Есть железяка, gateway 8200 с контролером aic7890 и ami megaraid. 4 >> диска segate cheetah в raid 5. Как я понимаю непрерывный трансфер >> должен быть порядка 40-50Мb/s. Хотя hdparm дает следующее: >> #hdparm -tT /dev/sda >> >> /dev/sda: >> Timing buffer-cache reads: 492 MB in 2.00 seconds = 246.00 MB/sec >> Timing buffered disk reads: 26 MB in 3.16 seconds = 8.23 MB/sec >> >> Помогите разобраться с этой проблемой, или наставте на путь истинный. >> P.S. Кусок dmesg в атаче. KL> irq conflict? Плохая терминация? Какой размер кеша на megaraid? KL> например, с MegaRAID Elite 1600 след. картина: KL> root@cedar ~# hdparm -tT /dev/sda KL> /dev/sda: KL> Timing buffer-cache reads: 864 MB in 2.00 seconds = 432.00 MB/sec KL> Timing buffered disk reads: 186 MB in 3.01 seconds = 61.79 MB/sec KL> root@cedar ~# KL> root@cedar ~# cat /proc/megaraid/0/config KL> MegaRAID Elite 1600 KL> Controller Type: 438/466/467/471/493 KL> Controller Supports 40 Logical Drives KL> Controller / Driver uses 64 bit memory addressing KL> Base = f8825000, Irq = 21, Logical Drives = 1, Channels = 2 KL> Version =G170:F316, DRAM = 128Mb KL> Controller Queue Depth = 254, Driver Queue Depth = 126 KL> правда у меня raid10 Спасибо, что ответили на мое письмо. Конфиг привожу: # cat /proc/megaraid/0/config Controller Type: 418/428/434 Base = 00002810, Irq = 9, Logical Drives = 1, Channels = 3 Version =Xl75:1.42, DRAM = 4Mb Controller Queue Depth = 254, Driver Queue Depth = 126 По поводу irq есть ругань acpi: ACPI: have wakeup address 0xc0001000 On node 0 totalpages: 32768 zone(0): 4096 pages. zone(1): 28672 pages. zone(2): 0 pages. ACPI: Unable to locate RSDP ACPI: Subsystem revision 20021122 PCI: PCI BIOS revision 2.10 entry at 0xfd95e, last bus=2 PCI: Using configuration type 1 ACPI: System description tables not found ACPI-0066: *** Error: Acpi_load_tables: Could not get RSDP, AE_NOT_FOUND ACPI-0116: *** Error: Acpi_load_tables: Could not load tables: AE_NOT_FOUND ACPI: Unable to load the System Description Tables PCI: Probing PCI hardware PCI: ACPI tables contain no PCI IRQ routing entries PCI: Probing PCI hardware (bus 00) PCI: Using IRQ router PIIX [8086/7110] at 00:02.0 PCI: Cannot allocate resource region 4 of device 00:02.1 Limiting direct PCI/PCI transfers. Как я понимаю проблемма скорее всего в этом. -- Best regards, Alexey ^ permalink raw reply [flat|nested] 6+ messages in thread
* [Comm] Re: скорость raid 5 2003-09-30 7:21 ` Alexey Berezkin @ 2003-09-30 19:03 ` Konstantin Lepikhov 2003-10-01 8:50 ` Alexey Berezkin 0 siblings, 1 reply; 6+ messages in thread From: Konstantin Lepikhov @ 2003-09-30 19:03 UTC (permalink / raw) To: community Hi Alexey! Tuesday 30, at 10:21:01 AM you wrote: <skip> > Спасибо, что ответили на мое письмо. Конфиг привожу: > # cat /proc/megaraid/0/config > Controller Type: 418/428/434 > Base = 00002810, Irq = 9, Logical Drives = 1, Channels = 3 > Version =Xl75:1.42, DRAM = 4Mb > Controller Queue Depth = 254, Driver Queue Depth = 126 > > По поводу irq есть ругань acpi: > > ACPI: have wakeup address 0xc0001000 > On node 0 totalpages: 32768 > zone(0): 4096 pages. > zone(1): 28672 pages. > zone(2): 0 pages. > ACPI: Unable to locate RSDP > > > ACPI: Subsystem revision 20021122 > PCI: PCI BIOS revision 2.10 entry at 0xfd95e, last bus=2 > PCI: Using configuration type 1 > ACPI: System description tables not found > ACPI-0066: *** Error: Acpi_load_tables: Could not get RSDP, AE_NOT_FOUND > ACPI-0116: *** Error: Acpi_load_tables: Could not load tables: AE_NOT_FOUND материнка на i845? %) Попробуйте обновить ядро + acpi patch + задействовать ACPI IRQ routing. > ACPI: Unable to load the System Description Tables > PCI: Probing PCI hardware > PCI: ACPI tables contain no PCI IRQ routing entries > PCI: Probing PCI hardware (bus 00) > PCI: Using IRQ router PIIX [8086/7110] at 00:02.0 > PCI: Cannot allocate resource region 4 of device 00:02.1 > Limiting direct PCI/PCI transfers. > > Как я понимаю проблемма скорее всего в этом. maybe -- WBR, Konstantin chat with ==>ICQ: 109916175 Lepikhov, speak to ==>JID: lakostis@jabber.org aka L.A. Kostis write to ==>mailto:lakostis@pisem.net.nospam ...The information is like the bank... (c) EC8OR ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Comm] Re: скорость raid 5 2003-09-30 19:03 ` Konstantin Lepikhov @ 2003-10-01 8:50 ` Alexey Berezkin 2003-10-02 19:04 ` Konstantin Lepikhov 0 siblings, 1 reply; 6+ messages in thread From: Alexey Berezkin @ 2003-10-01 8:50 UTC (permalink / raw) To: Konstantin Lepikhov Hello Konstantin, Tuesday, September 30, 2003, 10:03:31 PM, you wrote: KL> материнка на i845? %) Попробуйте обновить ядро + acpi patch + KL> задействовать ACPI IRQ routing. Да нет, материнка bx двухпроцессорная, стоит один PII 400 Пробовал отключить acpi, ругань исчезла, но и производительность не изменилась. Прерывания вроде получает нормально. Ide винт на этой же машине работает в два раза быстрей (по скорости диска, кеш примерно так же). -- Best regards, Alexey mailto:alex@kreschatic.kiev.ua ^ permalink raw reply [flat|nested] 6+ messages in thread
* [Comm] Re: скорость raid 5 2003-10-01 8:50 ` Alexey Berezkin @ 2003-10-02 19:04 ` Konstantin Lepikhov 0 siblings, 0 replies; 6+ messages in thread From: Konstantin Lepikhov @ 2003-10-02 19:04 UTC (permalink / raw) To: community Hi Alexey! Wednesday 01, at 11:50:26 AM you wrote: > Hello Konstantin, > > Tuesday, September 30, 2003, 10:03:31 PM, you wrote: > > > KL> материнка на i845? %) Попробуйте обновить ядро + acpi patch + > KL> задействовать ACPI IRQ routing. > > Да нет, материнка bx двухпроцессорная, стоит один PII 400 > Пробовал отключить acpi, ругань исчезла, но и производительность не > изменилась. Прерывания вроде получает нормально. Ide винт на этой же > машине работает в два раза быстрей (по скорости диска, кеш примерно > так же). значит, кривой биос. -- WBR, Konstantin chat with ==>ICQ: 109916175 Lepikhov, speak to ==>JID: lakostis@jabber.org aka L.A. Kostis write to ==>mailto:lakostis@pisem.net.nospam ...The information is like the bank... (c) EC8OR ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2003-10-02 19:04 UTC | newest] Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2003-09-29 8:53 [Comm] скорость raid 5 Alexey Berezkin 2003-09-29 17:00 ` [Comm] " Konstantin Lepikhov 2003-09-30 7:21 ` Alexey Berezkin 2003-09-30 19:03 ` Konstantin Lepikhov 2003-10-01 8:50 ` Alexey Berezkin 2003-10-02 19:04 ` Konstantin Lepikhov
ALT Linux Community general discussions This inbox may be cloned and mirrored by anyone: git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 community community/ http://lore.altlinux.org/community \ mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com public-inbox-index community Example config snippet for mirrors. Newsgroup available over NNTP: nntp://lore.altlinux.org/org.altlinux.lists.community AGPL code for this site: git clone https://public-inbox.org/public-inbox.git