From: "Dmytro O. Redchuk" <dor@kiev-online.net> To: community@altlinux.ru Subject: [Comm] Re: USB problem Date: Thu, 7 Aug 2003 09:24:15 +0300 Message-ID: <20030807062415.GB2033@kiev-online.net> (raw) In-Reply-To: <20030806193716.72f9f937.vsu@altlinux.ru> On Wed, Aug 06, 2003 at 07:37:16PM +0400, Sergey Vlasov wrote: > On Wed, 6 Aug 2003 18:29:10 +0300 > "Dmytro O. Redchuk" <dor@kiev-online.net> wrote: > > > > Тогда acpi=off :-( > > Стало лучше, но ... или хуже?-) > > > > Короче, после втыкания появляются строчки про sda: sda1 sda2... (и > > ёмкость правильная), но ругань на sdb про непонятный размер блока и > > ёмкость в один гиг... > > > > И монтироваться не хочет, I/O error. Ни sda[1-4], ни sdb1 > > Так, теперь подробнее: что за аппарат (/proc/bus/usb/devices), что тут ничего (вывод ниже) на апарате написано Apacer handy steno 1.1 (128M) > возникает в dmesg при обнаружении устройства и попытках монтирования? [dima@fox dima]$ mount /mnt/flash/ mount: /dev/sda1 is not a valid block device (конечно, его же даже в устройствах нет...) .... usb.c: USB device not accepting new address=6 (error=-110) hub.c: new USB device 00:10.3-1, assigned address 7 usb_control/bulk_msg: timeout usb.c: USB device not accepting new address=7 (error=-110) hub.c: new USB device 00:10.3-1, assigned address 8 SCSI subsystem driver Revision: 1.00 hdg: attached ide-scsi driver. scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: TEAC Model: CD-W540E Rev: 1.0C Type: CD-ROM ANSI SCSI revision: 02 usb_control/bulk_msg: timeout usb.c: USB device not accepting new address=8 (error=-110) hub.c: new USB device 00:10.3-1, assigned address 9 usb_control/bulk_msg: timeout usb.c: USB device not accepting new address=9 (error=-110) hub.c: new USB device 00:10.3-1, assigned address 10 .... [dima@fox dima]$ cat /proc/interrupts CPU0 0: 73628 IO-APIC-edge timer 1: 2039 IO-APIC-edge keyboard 2: 0 XT-PIC cascade 8: 1 IO-APIC-edge rtc 9: 0 IO-APIC-level acpi 10: 0 IO-APIC-edge usb-uhci, usb-uhci, usb-uhci, VIA8233 11: 0 IO-APIC-edge ehci-hcd 12: 9549 IO-APIC-edge PS/2 Mouse 14: 8758 IO-APIC-edge ide2 15: 4 IO-APIC-edge ide3 16: 49818 IO-APIC-level nvidia 18: 1428 IO-APIC-level eth0 NMI: 0 LOC: 73593 ERR: 0 MIS: 0 [dima@fox dima]$ > Со старыми ядрами работало? Если работало - с какой точно версией? Вечером попробовал дома -- на 2.4.20-up-alt5 -- работает. Мамка такая же, только версию биоса не записал, понадеявшись на склероз. Буду смотреть на апдейты биоса... Вот usb/devices: [dima@fox dima]$ cat /proc/bus/usb/devices T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.04 S: Manufacturer=Linux 2.4.21rel-std-up-alt7 ehci-hcd S: Product=VIA Technologies, Inc. USB 2.0 S: SerialNumber=00:10.3 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 0.00 S: Product=USB UHCI Root Hub S: SerialNumber=dc00 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 0.00 S: Product=USB UHCI Root Hub S: SerialNumber=d800 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 0.00 S: Product=USB UHCI Root Hub S: SerialNumber=d400 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms -- _,-=._ /|_/| `-.} `=._,.-=-._., @ @._, `._ _,-. ) _,.-' ` G.m-"^m`m' Dmytro O. Redchuk XMMS: ... silence.
next prev parent reply other threads:[~2003-08-07 6:24 UTC|newest] Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top 2003-08-06 14:42 [Comm] " Dmytro O. Redchuk 2003-08-06 14:51 ` [Comm] " Sergey Vlasov 2003-08-06 15:29 ` Dmytro O. Redchuk 2003-08-06 15:37 ` Sergey Vlasov 2003-08-07 6:24 ` Dmytro O. Redchuk [this message] 2003-08-07 10:32 ` Dmytro O. Redchuk 2003-08-07 12:40 ` Sergey Vlasov 2003-08-07 13:15 ` Dmytro O. Redchuk 2003-08-07 13:33 ` Sergey Vlasov 2003-08-07 14:11 ` Dmytro O. Redchuk 2003-08-07 14:53 ` Sergey Vlasov 2003-08-08 6:15 ` Dmytro O. Redchuk 2003-08-08 12:57 ` Dmytro O. Redchuk
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20030807062415.GB2033@kiev-online.net \ --to=dor@kiev-online.net \ --cc=community@altlinux.ru \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: link
ALT Linux Community general discussions This inbox may be cloned and mirrored by anyone: git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 community community/ http://lore.altlinux.org/community \ mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com public-inbox-index community Example config snippet for mirrors. Newsgroup available over NNTP: nntp://lore.altlinux.org/org.altlinux.lists.community AGPL code for this site: git clone https://public-inbox.org/public-inbox.git