From: Dmitry Kovalsky <dikov@imbg.org.ua>
To: community@altlinux.ru
Subject: Re: [Comm] cdrecord _NEC
Date: Fri, 30 May 2003 13:29:46 +0300
Message-ID: <200305301329.46416.dikov@imbg.org.ua> (raw)
In-Reply-To: <200305292321.31754.sinom@ktk.ru>
On Thursday 29 May 2003 18:21, sinom wrote:
Это изза того что резак новый (как уже и было написано)
У меня СДРВ AOpen-4852
ему скорости выставляй - невыставляй пишет как хочет
если ставлю скорость 4 то он начинает писать с 18-22 заканчивает на 40-48 --
макимальные скорости :0) -- причем болванки пишет идеально!
если ставить бОльшие скорости 16---- то ьакие же болванки запарываються точно
также как и у Вас :0)
Неро только самый свежий его понимает или очень старый ( v. 5.3)
насколько я понимаю это действительно дело в дровах к писалке -- cdrecord его
пока не понимает
Дима
> Здравствуйте!
>
> Сегодня приобрел резак фирмы NEC.
> В lilo.conf прописал append="hdb=ide-scsi" после чего появилось:
>
> $ cdrecord -scanbus
> Cdrecord 2.0 (i586-alt-linux-gnu) Copyright (C) 1995-2002 JЖrg Schilling
> Linux sg driver version: 3.1.24
> Using libscg version 'schily-0.7'
> scsibus0:
> 0,0,0 0) '_NEC ' 'CD-RW NR-9300A ' '2.12' Removable CD-ROM
> 0,1,0 1) *
> 0,2,0 2) *
> 0,3,0 3) *
> 0,4,0 4) *
> 0,5,0 5) *
> 0,6,0 6) *
> 0,7,0 7) *
>
> При попытке что-либо писать пишет только первые несколько мегобайт, после
> чего вылетает с ошибкой. После этого, например, можно просмотреть первае
> несколько секунд фильма, или прослушать первую _часть_ mp3. Вот что
> говорит:
>
> $ cdrecord -v dev=0,0,0 music.iso
> Cdrecord 2.0 (i586-alt-linux-gnu) Copyright (C) 1995-2002 JЖrg Schilling
> TOC Type: 1 = CD-ROM
> scsidev: '0,0,0'
> scsibus: 0 target: 0 lun: 0
> Linux sg driver version: 3.1.24
> Using libscg version 'schily-0.7'
> atapi: 1
> Device type : Removable CD-ROM
> Version : 0
> Response Format: 2
> Capabilities :
> Vendor_info : '_NEC '
> Identifikation : 'CD-RW NR-9300A '
> Revision : '2.12'
> Device seems to be: Generic mmc CD-RW.
> Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
> Driver flags : MMC-3 SWABAUDIO BURNFREE
> Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
> Drive buf size : 1226752 = 1198 KB
> FIFO size : 4194304 = 4096 KB
> Track 01: data 638 MB
> Total size: 732 MB (72:35.57) = 326668 sectors
> Lout start: 733 MB (72:37/43) = 326668 sectors
> Current Secsize: 2048
> ATIP info from disk:
> Indicated writing power: 5
> Reference speed: 2
> Is not unrestricted
> Is erasable
> ATIP start of lead in: -11635 (97:26/65)
> ATIP start of lead out: 359849 (79:59/74)
> 1T speed low: 0 (reserved val 0) 1T speed high: 4
> 2T speed low: 8 2T speed high: 0 (reserved val 10)
> power mult factor: 4 6
> recommended erase/write power: 3
> A1 values: 02 4C B0
> A2 values: 4A C8 36
> Disk type: Phase change
> Manuf. index: 3
> Manufacturer: CMC Magnetics Corporation
> Blocks total: 359849 Blocks current: 359849 Blocks remaining: 33181
> Starting to write CD/DVD at speed 4 in real TAO mode for single session.
> Last chance to quit, starting real write 0 seconds. Operation starts.
> Waiting for reader process to fill input buffer ... input buffer ready.
> BURN-Free is OFF.
> Performing OPC...
> Starting new track at sector: 0
> Track 01: 1 of 638 MB written (fifo 96%) [buf 89%] 112.8x.cdrecord:
> Input/output error. write_g1: scsi sendcmd: no error
> CDB: 2A 00 00 00 02 6C 00 00 1F 00
> status: 0x2 (CHECK CONDITION)
> Sense Bytes: 70 00 04 00 00 00 00 0A 00 00 00 00 08 03 00 00
> Sense Key: 0x4 Hardware Error, Segment 0
> Sense Code: 0x08 Qual 0x03 (logical unit communication crc error
> (ultra-dma/32)) Fru 0x0
> Sense flags: Blk 0 (not valid)
> cmd finished after 1.389s timeout 40s
>
> write track data: error after 1269760 bytes
> Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00
> Writing time: 11.500s
> Average write speed 651.2x.
> Fixating...
> Fixating time: 62.569s
> cdrecord: fifo had 84 puts and 21 gets.
> cdrecord: fifo was 0 times empty and 2 times full, min fill was 85%.
>
> Вопрос стандартный. Что делать?
>
> З.Ы. Система Мастер2.2
>
> --
> Роман
> _______________________________________________
> Community mailing list
> Community@altlinux.ru
> http://www.altlinux.ru/mailman/listinfo/community
--
Sincerely yours,
Ph.D. Student Dmytro Kovalskyy
Institute of Molecular Biology & Genetics
150 Akad. Zabolotnogo Street,
Kiev-143, 03143
UKRAINE
E-mail: dikov@imbg.org.ua
Fax: +380 (44) 266-0759
Tel.: +380 (44) 266-5589
next prev parent reply other threads:[~2003-05-30 10:29 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-05-29 15:21 sinom
2003-05-29 17:45 ` Sergey S. Skulachenko
2003-05-30 2:03 ` sinom
2003-05-30 17:01 ` Gleb Kulikov
2003-05-30 3:34 ` Mike Lykov
2003-05-30 9:59 ` sinom
2003-05-30 10:22 ` Владимир
2003-05-30 10:42 ` Antonio
2003-05-31 10:07 ` Re[2]: " metalking
2003-06-02 8:23 ` Antonio
2003-05-30 10:29 ` Dmitry Kovalsky [this message]
2003-05-30 10:59 ` Aleksey Korotkov
2003-05-30 6:47 ` Antonio
2003-05-30 18:29 ` Sergey S. Skulachenko
2003-06-01 9:34 ` [Comm] " Oleg N. Kayunov
2003-06-01 12:39 ` Maxim Tyurin
2003-06-06 6:36 ` Oleg N. Kayunov
2003-06-06 7:13 ` Antonio
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200305301329.46416.dikov@imbg.org.ua \
--to=dikov@imbg.org.ua \
--cc=community@altlinux.ru \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
ALT Linux Community general discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
public-inbox-index community
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.community
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git