From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: From: sinom To: Date: Thu, 29 May 2003 23:21:31 +0800 User-Agent: KMail/1.5 MIME-Version: 1.0 Content-Type: text/plain; charset="koi8-r" Content-Transfer-Encoding: 8bit Content-Disposition: inline Message-Id: <200305292321.31754.sinom@ktk.ru> Subject: [Comm] cdrecord _NEC Sender: community-admin@altlinux.ru Errors-To: community-admin@altlinux.ru X-BeenThere: community@altlinux.ru X-Mailman-Version: 2.0.9 Precedence: bulk Reply-To: community@altlinux.ru List-Unsubscribe: , List-Id: List-Post: List-Help: List-Subscribe: , List-Archive: Archived-At: List-Archive: List-Post: Здравствуйте! Сегодня приобрел резак фирмы NEC. В lilo.conf прописал append="hdb=ide-scsi" после чего появилось: $ cdrecord -scanbus Cdrecord 2.0 (i586-alt-linux-gnu) Copyright (C) 1995-2002 JЖrg Schilling Linux sg driver version: 3.1.24 Using libscg version 'schily-0.7' scsibus0: 0,0,0 0) '_NEC ' 'CD-RW NR-9300A ' '2.12' Removable CD-ROM 0,1,0 1) * 0,2,0 2) * 0,3,0 3) * 0,4,0 4) * 0,5,0 5) * 0,6,0 6) * 0,7,0 7) * При попытке что-либо писать пишет только первые несколько мегобайт, после чего вылетает с ошибкой. После этого, например, можно просмотреть первае несколько секунд фильма, или прослушать первую _часть_ mp3. Вот что говорит: $ cdrecord -v dev=0,0,0 music.iso Cdrecord 2.0 (i586-alt-linux-gnu) Copyright (C) 1995-2002 JЖrg Schilling TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.1.24 Using libscg version 'schily-0.7' atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : '_NEC ' Identifikation : 'CD-RW NR-9300A ' Revision : '2.12' Device seems to be: Generic mmc CD-RW. Using generic SCSI-3/mmc CD-R driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R Drive buf size : 1226752 = 1198 KB FIFO size : 4194304 = 4096 KB Track 01: data 638 MB Total size: 732 MB (72:35.57) = 326668 sectors Lout start: 733 MB (72:37/43) = 326668 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 5 Reference speed: 2 Is not unrestricted Is erasable ATIP start of lead in: -11635 (97:26/65) ATIP start of lead out: 359849 (79:59/74) 1T speed low: 0 (reserved val 0) 1T speed high: 4 2T speed low: 8 2T speed high: 0 (reserved val 10) power mult factor: 4 6 recommended erase/write power: 3 A1 values: 02 4C B0 A2 values: 4A C8 36 Disk type: Phase change Manuf. index: 3 Manufacturer: CMC Magnetics Corporation Blocks total: 359849 Blocks current: 359849 Blocks remaining: 33181 Starting to write CD/DVD at speed 4 in real TAO mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. BURN-Free is OFF. Performing OPC... Starting new track at sector: 0 Track 01: 1 of 638 MB written (fifo 96%) [buf 89%] 112.8x.cdrecord: Input/output error. write_g1: scsi sendcmd: no error CDB: 2A 00 00 00 02 6C 00 00 1F 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 04 00 00 00 00 0A 00 00 00 00 08 03 00 00 Sense Key: 0x4 Hardware Error, Segment 0 Sense Code: 0x08 Qual 0x03 (logical unit communication crc error (ultra-dma/32)) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 1.389s timeout 40s write track data: error after 1269760 bytes Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00 Writing time: 11.500s Average write speed 651.2x. Fixating... Fixating time: 62.569s cdrecord: fifo had 84 puts and 21 gets. cdrecord: fifo was 0 times empty and 2 times full, min fill was 85%. Вопрос стандартный. Что делать? З.Ы. Система Мастер2.2 -- Роман