From: Ilia Menchikh <ilia@vitamin-e.ru>
To: community@altlinux.ru
Subject: [Comm] Test IDE-controller was: Странности с cdrecord
Date: Mon, 31 Mar 2003 13:17:13 +0400
Message-ID: <20030331131713.65327fec.ilia@vitamin-e.ru> (raw)
In-Reply-To: <E18zugF-0005Ny-00@host.orbita.udm.net>
On Mon, 31 Mar 2003 13:10:09 +0500
Rinat Bikatov <BiRin@orbita.udm.ru> wrote:
> у меня такое было при записи на записанную или испорченную (точно не
> помню) болванку. при записи на другую болванку - всё ок.
Нет, тут другое.
Как протестировать глюки IDE контроллера?
Симптомы такие:
При копировании/записи на диски больших файлов (от 100М) подскакивает
количество отъедаемой процессом памяти (>50%), заодно вылезает в топе
наверх bdflush. Воспроизводимо как локально, так и по самбе.
Железо:
Chaintech 6vjd2-100
Bus 0, device 17, function 1:
IDE interface: VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE
(rev 6). Master Capable. Latency=32.
I/O at 0xd000 [0xd00f].
В логах:
SCSI host 2 abort (pid 3094271) timed out - resetting
SCSI bus is being reset for host 2 channel 0.
scsi : aborting command due to timeout : pid 3094271, scsi2, channel 0,
id 0, lun 0 UNKNOWN(0x54) 01 00 00 00 00 00 00 00 00
SCSI host 2 abort (pid 3094271) timed out - resetting
SCSI bus is being reset for host 2
channel 0. scsi : aborting command due to timeout : pid 3094271, scsi2,
channel 0, id 0, lun 0 UNKNOWN(0x54) 01 00 00 00 00 00 00 00 00
<кусь то же самое>
SCSI host 2 abort (pid 3094271) timed out - resetting
SCSI bus is being reset for host 2 channel 0.
ide1: reset timed-out, status=0xd0
$ cat /proc/ide/via
----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.35
South Bridge: VIA vt8233
Revision: ISA 0x0 IDE 0x6
Highest DMA rate: UDMA100
BM-DMA base: 0xd000
PCI clock: 33.3MHz
Master Read Cycle IRDY: 0ws
Master Write Cycle IRDY: 0ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: no no
Post Write Buffer: no no
Enabled: yes yes
Simplex only: no no
Cable Type: 80w 80w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: PIO UDMA PIO PIO
Address Setup: 120ns 30ns 30ns 30ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 30ns 30ns
Data Active: 330ns 90ns 90ns 90ns
Data Recovery: 270ns 30ns 30ns 30ns
Cycle Time: 600ns 20ns 120ns 120ns
Transfer Rate: 3.3MB/s 99.9MB/s 16.6MB/s 16.6MB/s
Hdparm показывает другое:
СD-RW:
$ sudo hdparm -i /dev/hdc
/dev/hdc:
Model=_NEC NR-7500A, FwRev=1.20, SerialNo=
Config={ Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=0kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
IORDY=yes, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
AdvancedPM=no
Винт:
$ sudo hdparm -i /dev/hdd
/dev/hdd:
Model=ST340016A, FwRev=7.73, SerialNo=3HR2HX28
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version: 1 2 3 4 5
Короче, что полетело - резак или контроллер? И как это точнее
определить.
PS. Машина под нагрузкой - самбовая файлопомойка, без серьезных
нареканий несколько месяцев.
Как говорится - Help need!
--
Regards
Ilia Menchikh
JID ililina@jabber.vitamin-e.ru
prev parent reply other threads:[~2003-03-31 9:17 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-03-31 6:41 [Comm] " Ilia Menchikh
2003-03-31 8:10 ` Rinat Bikatov
2003-03-31 9:17 ` Ilia Menchikh [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20030331131713.65327fec.ilia@vitamin-e.ru \
--to=ilia@vitamin-e.ru \
--cc=community@altlinux.ru \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
ALT Linux Community general discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
public-inbox-index community
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.community
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git