* [mdk-re] HPT370 @ 2001-04-12 10:10 Maxim Savrilov 2001-04-12 10:21 ` Anton Farygin ` (2 more replies) 0 siblings, 3 replies; 27+ messages in thread From: Maxim Savrilov @ 2001-04-12 10:10 UTC (permalink / raw) To: mandrake-russian Hi! Вот переставил винт с hda на hde, который на HPT370 Говорю hdparm -t /dev/hde он мне - 30mb/s на hda было 20. Можно ли как-то увеличить быстродействие без вреда для здоровья? Мать ABIT BX133-RAID винт Quantum Fireball AS20 Thanks. ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [mdk-re] HPT370 2001-04-12 10:10 [mdk-re] HPT370 Maxim Savrilov @ 2001-04-12 10:21 ` Anton Farygin 2001-04-12 10:22 ` Yura Zotov 2001-04-12 18:30 ` Igor Solovyov 2 siblings, 0 replies; 27+ messages in thread From: Anton Farygin @ 2001-04-12 10:21 UTC (permalink / raw) To: mandrake-russian Maxim Savrilov wrote: > Hi! > Вот переставил винт с hda на hde, который на HPT370 > Говорю hdparm -t /dev/hde > он мне - 30mb/s > на hda было 20. > Можно ли как-то увеличить быстродействие без вреда для здоровья? > Мать ABIT BX133-RAID > винт Quantum Fireball AS20 > Thanks. 30Mb - максимум, который можно вытянуть из этого винта. У меня IBM DTLA на подобном девайсе показывает 35Mb/s Rgds Anton ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [mdk-re] HPT370 2001-04-12 10:10 [mdk-re] HPT370 Maxim Savrilov 2001-04-12 10:21 ` Anton Farygin @ 2001-04-12 10:22 ` Yura Zotov 2001-04-12 18:30 ` Igor Solovyov 2 siblings, 0 replies; 27+ messages in thread From: Yura Zotov @ 2001-04-12 10:22 UTC (permalink / raw) To: mandrake-russian On Thu, Apr 12, 2001 at 01:10:00PM +0700, Maxim Savrilov wrote: > Hi! > Вот переставил винт с hda на hde, который на HPT370 > Говорю hdparm -t /dev/hde > он мне - 30mb/s > на hda было 20. > Можно ли как-то увеличить быстродействие без вреда для здоровья? > Мать ABIT BX133-RAID > винт Quantum Fireball AS20 > Thanks. 30mb/sec это почти все, на что способен UDMA100 в данном случае. Дело в том, что hdparm -t показывает линейную скорость чтения диска, которая определяется конструкцией винчестера. Посмотрите на сайте производителя или еще где параметры своего диска, и если 30mb/sec соответствует спецификации, по большего от винчестера не добиться никак. У меня на DTLA 35mb/sec при 37 в спецификациях, по-моему это вполне приемлимое несоответствие. -- Юрий А. Зотов ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [mdk-re] HPT370 2001-04-12 10:10 [mdk-re] HPT370 Maxim Savrilov 2001-04-12 10:21 ` Anton Farygin 2001-04-12 10:22 ` Yura Zotov @ 2001-04-12 18:30 ` Igor Solovyov 2001-04-12 18:38 ` Yura Zotov 2 siblings, 1 reply; 27+ messages in thread From: Igor Solovyov @ 2001-04-12 18:30 UTC (permalink / raw) To: mandrake-russian Hi! On Thu, 12 Apr 2001 13:10:00 +0700 Maxim Savrilov <Maxim.Savrilov@oberon.novocybersk.ru> wrote: > Hi! > Вот переставил винт с hda на hde, который на HPT370 > Говорю hdparm -t /dev/hde > он мне - 30mb/s > на hda было 20. > Можно ли как-то увеличить быстродействие без вреда для здоровья? > Мать ABIT BX133-RAID > винт Quantum Fireball AS20 > Thanks. Вот поставьте их 4 штуки, да RAID-0 организуйте и будет вам все, что можно от UDMA-100 получить. :-) -- Best regards! Igor Solovyov Zlatoust, Russia ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [mdk-re] HPT370 2001-04-12 18:30 ` Igor Solovyov @ 2001-04-12 18:38 ` Yura Zotov 2001-04-12 19:59 ` Igor Solovyov 0 siblings, 1 reply; 27+ messages in thread From: Yura Zotov @ 2001-04-12 18:38 UTC (permalink / raw) To: mandrake-russian On Thu, Apr 12, 2001 at 08:29:38PM +0600, Igor Solovyov wrote: > Hi! > On Thu, 12 Apr 2001 13:10:00 +0700 > Maxim Savrilov <Maxim.Savrilov@oberon.novocybersk.ru> wrote: > > > Hi! > > Вот переставил винт с hda на hde, который на HPT370 > > Говорю hdparm -t /dev/hde > > он мне - 30mb/s > > на hda было 20. > > Можно ли как-то увеличить быстродействие без вреда для здоровья? > > Мать ABIT BX133-RAID > > винт Quantum Fireball AS20 > > Thanks. > > Вот поставьте их 4 штуки, да RAID-0 организуйте и будет вам все, > что можно от UDMA-100 получить. :-) А разве на HPT370 RAID поддерживается? Кем? Как? На каком ядре и с какими настройками у вас работает RAID на HPT370? > > -- > Best regards! > Igor Solovyov > Zlatoust, Russia > - Юрий А. Зотов ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [mdk-re] HPT370 2001-04-12 18:38 ` Yura Zotov @ 2001-04-12 19:59 ` Igor Solovyov 2001-04-12 20:51 ` Yura Zotov 2001-04-14 11:27 ` Re[2]: " Sergey Krivulja 0 siblings, 2 replies; 27+ messages in thread From: Igor Solovyov @ 2001-04-12 19:59 UTC (permalink / raw) To: mandrake-russian Hi! On Thu, 12 Apr 2001 18:36:45 +0400 Yura Zotov <yz-news@mail.ru> wrote: > On Thu, Apr 12, 2001 at 08:29:38PM +0600, Igor Solovyov wrote: > > Hi! > > On Thu, 12 Apr 2001 13:10:00 +0700 > > Maxim Savrilov <Maxim.Savrilov@oberon.novocybersk.ru> wrote: > > > > > Hi! > > > Вот переставил винт с hda на hde, который на HPT370 > > > Говорю hdparm -t /dev/hde > > > он мне - 30mb/s > > > на hda было 20. > > > Можно ли как-то увеличить быстродействие без вреда для здоровья? > > > Мать ABIT BX133-RAID > > > винт Quantum Fireball AS20 > > > Thanks. > > > > Вот поставьте их 4 штуки, да RAID-0 организуйте и будет вам все, > > что можно от UDMA-100 получить. :-) > > А разве на HPT370 RAID поддерживается? Кем? Как? На каком ядре и с какими > настройками у вас работает RAID на HPT370? А что Вы имеете в виду? Сам контроллер HPT-370? Так я его поддержку наблюдаю еще с ядра 2.2.16 от IPLabs (в то время). С того момента и RAID работает. Я даже тогда писал сюда отчет по его испытаниям на скорострельность. Если есть возможность поискать в архивах за пршлый год, то письма назывались что-то типа: My fighting with HPT-370. -- Best regards! Igor Solovyov Zlatoust, Russia ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [mdk-re] HPT370 2001-04-12 19:59 ` Igor Solovyov @ 2001-04-12 20:51 ` Yura Zotov 2001-04-12 22:21 ` Igor Solovyov 2001-04-14 11:27 ` Re[2]: " Sergey Krivulja 1 sibling, 1 reply; 27+ messages in thread From: Yura Zotov @ 2001-04-12 20:51 UTC (permalink / raw) To: mandrake-russian On Thu, Apr 12, 2001 at 09:54:18PM +0600, Igor Solovyov wrote: > Hi! > On Thu, 12 Apr 2001 18:36:45 +0400 > Yura Zotov <yz-news@mail.ru> wrote: > > > On Thu, Apr 12, 2001 at 08:29:38PM +0600, Igor Solovyov wrote: > > > Hi! > > > On Thu, 12 Apr 2001 13:10:00 +0700 > > > Maxim Savrilov <Maxim.Savrilov@oberon.novocybersk.ru> wrote: > > > > > > > Hi! > > > > Вот переставил винт с hda на hde, который на HPT370 > > > > Говорю hdparm -t /dev/hde > > > > он мне - 30mb/s > > > > на hda было 20. > > > > Можно ли как-то увеличить быстродействие без вреда для здоровья? > > > > Мать ABIT BX133-RAID > > > > винт Quantum Fireball AS20 > > > > Thanks. > > > > > > Вот поставьте их 4 штуки, да RAID-0 организуйте и будет вам все, > > > что можно от UDMA-100 получить. :-) > > > > А разве на HPT370 RAID поддерживается? Кем? Как? На каком ядре и с какими > > настройками у вас работает RAID на HPT370? > > А что Вы имеете в виду? Сам контроллер HPT-370? Так я его > поддержку наблюдаю еще с ядра 2.2.16 от IPLabs (в то время). > С того момента и RAID работает. Я даже тогда писал сюда отчет > по его испытаниям на скорострельность. Если есть возможность > поискать в архивах за пршлый год, то письма назывались что-то > типа: My fighting with HPT-370. > Там архив только за декабрь. Не могли бы вы написать подробнее про запуск RAID на HPT370? Я был бы очень благодарен. Интересуют настройки ядра, режимы RAID. Просто мой знакомый уже отчаялся и имеет твердое убеждение, что RAID не поддерживается. У него никак не получается. Пожалуйста, напишите в подробностях, как это работает. > -- > Best regards! > Igor Solovyov > Zlatoust, Russia - Юрий А. Зотов ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [mdk-re] HPT370 2001-04-12 20:51 ` Yura Zotov @ 2001-04-12 22:21 ` Igor Solovyov 2001-04-13 0:10 ` Yura Zotov 0 siblings, 1 reply; 27+ messages in thread From: Igor Solovyov @ 2001-04-12 22:21 UTC (permalink / raw) To: mandrake-russian Hi! On Thu, 12 Apr 2001 20:51:04 +0400 Yura Zotov <yz-news@mail.ru> wrote: > Там архив только за декабрь. Не могли бы вы написать подробнее про запуск > RAID на HPT370? Я был бы очень благодарен. Интересуют настройки ядра, > режимы RAID. Просто мой знакомый уже отчаялся и имеет твердое убеждение, > что RAID не поддерживается. У него никак не получается. Пожалуйста, > напишите в подробностях, как это работает. Делаем RAID-0 массив, нажав Ctr-H, в момент загрузки BIOS-а контроллера HPT-370. Хотя это наверное Вы и сами знаете. :-) Затем надо выяснить ресурсы используемые контроллером. Проще всего подглядеть под Windows (в свойствах контроллера). Для моей "мамы" Abit BE6-II получаем: a. D400-D407 b. D800-D803 c. DC00-DC07 d. E000-E003 e. E400-E4FF IRQ - 11 Читаем Ultra-DMA Mini-HOWTO. Выясняем, что при загрузке ядру надо передать параметры следующим образом: ide2=a,b+2 ide3=c,d+2 (где a,b,c,d - вышеприведенные адреса). Плюем на все это и прибавлем не 2, а 3, для пущей важности добавив номер прерывания. :-))))) Т.е.: ide2=0xd400,0xd803,11 ide3=0xdc00,0xe003,11 При загрузке вводим параметры для ядра: boot: linux ide2=0xd400,0xd802,11 ide3=0xdc00,0xe002,11 Все. RAID-массив доступен. Разбиваем на разделы. Хотя я, на самом деле разбивку и создание файловых систем (e2fs и swap) произвожу System Commander-ом еще до загрузки Linux. Он видит RAID без проблем. Еще бы умел reiserfs делать, вообще бы ему цены не было. :-) -- Best regards! Igor Solovyov Zlatoust, Russia ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [mdk-re] HPT370 2001-04-12 22:21 ` Igor Solovyov @ 2001-04-13 0:10 ` Yura Zotov 2001-04-13 15:46 ` Igor Solovyov 0 siblings, 1 reply; 27+ messages in thread From: Yura Zotov @ 2001-04-13 0:10 UTC (permalink / raw) To: mandrake-russian On Fri, Apr 13, 2001 at 12:19:06AM +0600, Igor Solovyov wrote: > Hi! > On Thu, 12 Apr 2001 20:51:04 +0400 > Yura Zotov <yz-news@mail.ru> wrote: > > Там архив только за декабрь. Не могли бы вы написать подробнее про запуск > > RAID на HPT370? Я был бы очень благодарен. Интересуют настройки ядра, > > режимы RAID. Просто мой знакомый уже отчаялся и имеет твердое убеждение, > > что RAID не поддерживается. У него никак не получается. Пожалуйста, > > напишите в подробностях, как это работает. > > Делаем RAID-0 массив, нажав Ctr-H, в момент загрузки BIOS-а контроллера HPT-370. > Хотя это наверное Вы и сами знаете. :-) > Затем надо выяснить ресурсы используемые контроллером. Проще всего > подглядеть под Windows (в свойствах контроллера). Для моей "мамы" > Abit BE6-II получаем: > > a. D400-D407 > b. D800-D803 > c. DC00-DC07 > d. E000-E003 > e. E400-E4FF > IRQ - 11 > > Читаем Ultra-DMA Mini-HOWTO. Выясняем, что при загрузке ядру надо передать > параметры следующим образом: ide2=a,b+2 ide3=c,d+2 (где a,b,c,d - вышеприведенные адреса). > Плюем на все это и прибавлем не 2, а 3, для пущей важности добавив номер прерывания. :-))))) > > Т.е.: ide2=0xd400,0xd803,11 ide3=0xdc00,0xe003,11 > > При загрузке вводим параметры для ядра: > boot: linux ide2=0xd400,0xd802,11 ide3=0xdc00,0xe002,11 > > Все. RAID-массив доступен. Разбиваем на разделы. > Хотя я, на самом деле разбивку и создание файловых систем (e2fs и swap) > произвожу System Commander-ом еще до загрузки Linux. > Он видит RAID без проблем. Еще бы умел reiserfs делать, вообще бы > ему цены не было. :-) > > -- > Best regards! > Igor Solovyov > Zlatoust, Russia В общем мы попробовали на ядре 2.4.3 со всякими параметрами что-то не вышел каменный цветок. Поддержку RAID в ядре включали. Не могли бы вы прислать лог загрузки ядра с работающим RAID, просто совершенно не понятно, что же у нас не так. Что у вас выдает hdparm -t для RAID? -- Юрий А. Зотов ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [mdk-re] HPT370 2001-04-13 0:10 ` Yura Zotov @ 2001-04-13 15:46 ` Igor Solovyov 2001-04-13 21:30 ` Yura Zotov 0 siblings, 1 reply; 27+ messages in thread From: Igor Solovyov @ 2001-04-13 15:46 UTC (permalink / raw) To: mandrake-russian Hi! On Fri, 13 Apr 2001 00:09:36 +0400 Yura Zotov <yz-news@mail.ru> wrote: > В общем мы попробовали на ядре 2.4.3 со всякими параметрами что-то не > вышел каменный цветок. Поддержку RAID в ядре включали. Не могли бы вы Это не та поддержка. Это поддержка программно-реализуемого RAID. Нужна лишь поддержка контроллера HPT366, да-да 366, в ядре значится именно этот чипсет. Но он полностью совместим с 370. > прислать лог загрузки ядра с работающим RAID, просто совершенно не > понятно, что же у нас не так. Что у вас выдает hdparm -t для RAID? А там обычные логи, просто вместо ide0 и ide1, значатся ide2 и ide3 соответственно. А сам массив видится как один большой HDD. hdparm -t выдает около 30 MB/sec для 2-х HDD UDMA-66. -- Best regards! Igor Solovyov Zlatoust, Russia ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [mdk-re] HPT370 2001-04-13 15:46 ` Igor Solovyov @ 2001-04-13 21:30 ` Yura Zotov 2001-04-13 22:53 ` Igor Solovyov 0 siblings, 1 reply; 27+ messages in thread From: Yura Zotov @ 2001-04-13 21:30 UTC (permalink / raw) To: mandrake-russian On Fri, Apr 13, 2001 at 05:45:37PM +0600, Igor Solovyov wrote: > Hi! > On Fri, 13 Apr 2001 00:09:36 +0400 > Yura Zotov <yz-news@mail.ru> wrote: > > > В общем мы попробовали на ядре 2.4.3 со всякими параметрами что-то не > > вышел каменный цветок. Поддержку RAID в ядре включали. Не могли бы вы > > Это не та поддержка. Это поддержка программно-реализуемого RAID. > Нужна лишь поддержка контроллера HPT366, да-да 366, в ядре > значится именно этот чипсет. Но он полностью совместим с 370. > > > прислать лог загрузки ядра с работающим RAID, просто совершенно не > > понятно, что же у нас не так. Что у вас выдает hdparm -t для RAID? > > А там обычные логи, просто вместо ide0 и ide1, значатся ide2 и ide3 > соответственно. А сам массив видится как один большой HDD. > hdparm -t выдает около 30 MB/sec для 2-х HDD UDMA-66. > > -- > Best regards! > Igor Solovyov > Zlatoust, Russia Добрый день. Из переписки все-таки осталось несколько непонятых вопросов. 1. Каким устройством являлся RAID (/dev/hde ?) ? 2. Были ли читабельны разделы на этом RAID из других OS (WinXX напр.)? У нас не видны диска в ext разделе, а те primary, что были видны не монтировались (bad superblock ...). 3. Все-таки, какие параметры передавались ядру ( b+2 или b+3), так как в Вашем письме в разных местах написано по-разному? У нас в случае b+2 все было как обычно, а при b+3 ядро висло на проверке разделов на /dev/hde. Пожалуйста, ответьте по-подробнее. (лог загрузки ядра не помешал бы :-) ) -- Юрий А. Зотов ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [mdk-re] HPT370 2001-04-13 21:30 ` Yura Zotov @ 2001-04-13 22:53 ` Igor Solovyov 2001-04-13 23:03 ` Igor Solovyov 0 siblings, 1 reply; 27+ messages in thread From: Igor Solovyov @ 2001-04-13 22:53 UTC (permalink / raw) To: mandrake-russian Hi! On Fri, 13 Apr 2001 21:30:21 +0400 Yura Zotov <yz-news@mail.ru> wrote: > Из переписки все-таки осталось несколько непонятых вопросов. > > 1. Каким устройством являлся RAID (/dev/hde ?) ? Да. /dev/hde > 2. Были ли читабельны разделы на этом RAID из других OS (WinXX напр.)? У > нас не видны диска в ext разделе, а те primary, что были видны не > монтировались (bad superblock ...). Они видны даже из ДОС. Все Windows 9x/Me разделы видят, но для полноценной поддержки (UDMA) все же требуют установки соответствующих дрйверов. Windows NT/2000 при установке RAID не распознают, но там есть возможность (нажав F6) установить драйверы с дискеты. После этого, все нормально. > 3. Все-таки, какие параметры передавались ядру ( b+2 или b+3), так как в > Вашем письме в разных местах написано по-разному? У нас в случае b+2 > все было как обычно, а при b+3 ядро висло на проверке разделов на > /dev/hde. Передавались и +2 и +3, разницы почему-то не было. Но я счел нужным передавать все же +3, поскольку именно в этом случае указывается весь диапазон адресов. Но, повторюсь, и +2 тоже работало. > Пожалуйста, ответьте по-подробнее. (лог загрузки ядра не помешал бы :-) ) К сожалению не могу этого сделать, т.к. в настоящий момент у меня один HDD, а посему RAID реализовать не могу. Просто у меня была возможность (когда контора приобрела новые компьютеры) временно взять для экспериментов два HDD. На них я и тренировался. Ядро было 2.2.16, а так же пробовалось и на 2.2.18 (оба сборки ipl из 7.0 RE). На новом ядре 2.4.2 не пробовал, может с ним какие проблемы? Хотя вроде бы не должно. В нем поддержка этого контроллера так же присутствует. -- Best regards! Igor Solovyov Zlatoust, Russia ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: [mdk-re] HPT370 2001-04-13 22:53 ` Igor Solovyov @ 2001-04-13 23:03 ` Igor Solovyov 0 siblings, 0 replies; 27+ messages in thread From: Igor Solovyov @ 2001-04-13 23:03 UTC (permalink / raw) To: mandrake-russian Hi! В догонку. А проблемы, подобные описанным Вами у меня тоже были, но с ядром 2.2.14 (т.е. с родным ядром 7.0 RE). Там был не совсем удачный в этом смысле ide-patch. -- Best regards! Igor Solovyov Zlatoust, Russia ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re[2]: [mdk-re] HPT370 2001-04-12 19:59 ` Igor Solovyov 2001-04-12 20:51 ` Yura Zotov @ 2001-04-14 11:27 ` Sergey Krivulja 2001-04-14 11:40 ` Igor Solovyov 1 sibling, 1 reply; 27+ messages in thread From: Sergey Krivulja @ 2001-04-14 11:27 UTC (permalink / raw) To: Igor Solovyov Hello Igor, >> >> А разве на HPT370 RAID поддерживается? Кем? Как? На каком ядре и с какими А зачем-же тогда его поставили на мать? От нечего делать :-\ Вот он и отвечает за RAID-0, т.е. простое зеркалирование. -- Best regards, Sergey mailto:skrivulja@erec.ru ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: Re[2]: [mdk-re] HPT370 2001-04-14 11:27 ` Re[2]: " Sergey Krivulja @ 2001-04-14 11:40 ` Igor Solovyov 2001-04-16 14:05 ` Re[4]: " Sergey Krivulja 0 siblings, 1 reply; 27+ messages in thread From: Igor Solovyov @ 2001-04-14 11:40 UTC (permalink / raw) To: mandrake-russian Hi! On Sat, 14 Apr 2001 11:27:21 +0400 Sergey Krivulja <skrivulja@erec.ru> wrote: > Hello Igor, > > >> > >> А разве на HPT370 RAID поддерживается? Кем? Как? На каком ядре и с какими > А зачем-же тогда его поставили на мать? От нечего делать :-\ > Вот он и отвечает за RAID-0, т.е. простое зеркалирование. RAID-0 это не зеркалирование, а просто объединение нескольких дисков в один. А вот RAID-1 - зеркалирование. Кстати, на этих мамах есть возможность сделать RAID-0+1. -- Best regards! Igor Solovyov Zlatoust, Russia ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re[4]: [mdk-re] HPT370 2001-04-14 11:40 ` Igor Solovyov @ 2001-04-16 14:05 ` Sergey Krivulja 2001-04-16 15:19 ` Re[5]: " Sergey Krivulja 0 siblings, 1 reply; 27+ messages in thread From: Sergey Krivulja @ 2001-04-16 14:05 UTC (permalink / raw) To: Igor Solovyov Hello Igor, >> >> >> >> А разве на HPT370 RAID поддерживается? Кем? Как? На каком ядре и с какими >> А зачем-же тогда его поставили на мать? От нечего делать :-\ >> Вот он и отвечает за RAID-0, т.е. простое зеркалирование. IS> RAID-0 это не зеркалирование, а просто объединение нескольких IS> дисков в один. А вот RAID-1 - зеркалирование. IS> Кстати, на этих мамах есть возможность сделать RAID-0+1. Так это стандартная фича для IDE контроллеров. -- Best regards, Sergey mailto:skrivulja@erec.ru ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re[5]: [mdk-re] HPT370 2001-04-16 14:05 ` Re[4]: " Sergey Krivulja @ 2001-04-16 15:19 ` Sergey Krivulja 2001-04-16 18:35 ` Igor Solovyov 0 siblings, 1 reply; 27+ messages in thread From: Sergey Krivulja @ 2001-04-16 15:19 UTC (permalink / raw) To: Sergey Krivulja Hello Sergey, Monday, April 16, 2001, 2:04:59 PM, you wrote: SK> Hello Igor, >>> >> >>> >> А разве на HPT370 RAID поддерживается? Кем? Как? На каком ядре и с какими >>> А зачем-же тогда его поставили на мать? От нечего делать :-\ >>> Вот он и отвечает за RAID-0, т.е. простое зеркалирование. IS>> RAID-0 это не зеркалирование, а просто объединение нескольких IS>> дисков в один. А вот RAID-1 - зеркалирование. IS>> Кстати, на этих мамах есть возможность сделать RAID-0+1. SK> Так это стандартная фича для IDE контроллеров. Извиняюсь за неточность. Я имею ввиду, что доп. контроллеры именно в таком исполнении ставят RAID-0+1. -- Best regards, Sergey mailto:skrivulja@erec.ru ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: Re[5]: [mdk-re] HPT370 2001-04-16 15:19 ` Re[5]: " Sergey Krivulja @ 2001-04-16 18:35 ` Igor Solovyov 2001-04-17 8:43 ` Re[7]: " Sergey Krivulja 2001-04-17 9:44 ` Vladimir Karpinsky 0 siblings, 2 replies; 27+ messages in thread From: Igor Solovyov @ 2001-04-16 18:35 UTC (permalink / raw) To: mandrake-russian Hi! On Mon, 16 Apr 2001 15:19:00 +0400 Sergey Krivulja <skrivulja@erec.ru> wrote: > IS>> RAID-0 это не зеркалирование, а просто объединение нескольких > IS>> дисков в один. А вот RAID-1 - зеркалирование. > IS>> Кстати, на этих мамах есть возможность сделать RAID-0+1. > SK> Так это стандартная фича для IDE контроллеров. > Извиняюсь за неточность. Я имею ввиду, что доп. контроллеры > именно в таком исполнении ставят RAID-0+1. Э.... Не очень понял о чем речь. Там есть возможность выбрать одно из трех: RAID-0, RAID-1 или RAID-0+1. (Для HPT-370 во всяком случае). -- Best regards! Igor Solovyov Zlatoust, Russia ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re[7]: [mdk-re] HPT370 2001-04-16 18:35 ` Igor Solovyov @ 2001-04-17 8:43 ` Sergey Krivulja 2001-04-17 19:57 ` Igor Solovyov 2001-04-17 9:44 ` Vladimir Karpinsky 1 sibling, 1 reply; 27+ messages in thread From: Sergey Krivulja @ 2001-04-17 8:43 UTC (permalink / raw) To: Igor Solovyov Hello Igor, IS> Э.... Не очень понял о чем речь. Там есть возможность выбрать одно IS> из трех: RAID-0, RAID-1 или RAID-0+1. (Для HPT-370 во всяком случае). Именно так. Для других все остается в силе. С другой стороны не следует ожидать большего от микросхемки за $4. -- Best regards, Sergey mailto:skrivulja@erec.ru ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: Re[7]: [mdk-re] HPT370 2001-04-17 8:43 ` Re[7]: " Sergey Krivulja @ 2001-04-17 19:57 ` Igor Solovyov 0 siblings, 0 replies; 27+ messages in thread From: Igor Solovyov @ 2001-04-17 19:57 UTC (permalink / raw) To: mandrake-russian Hi! On Tue, 17 Apr 2001 08:43:57 +0400 Sergey Krivulja <skrivulja@erec.ru> wrote: > Hello Igor, > > IS> Э.... Не очень понял о чем речь. Там есть возможность выбрать одно > IS> из трех: RAID-0, RAID-1 или RAID-0+1. (Для HPT-370 во всяком случае). > Именно так. Для других все остается в силе. С другой стороны не > следует ожидать большего от микросхемки за $4. Да и для "домашенего" использования большего и не надо. :-)))) -- Best regards! Igor Solovyov Zlatoust, Russia ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re[7]: [mdk-re] HPT370 2001-04-16 18:35 ` Igor Solovyov 2001-04-17 8:43 ` Re[7]: " Sergey Krivulja @ 2001-04-17 9:44 ` Vladimir Karpinsky 2001-04-17 17:51 ` Lenya L.Khachaturov 1 sibling, 1 reply; 27+ messages in thread From: Vladimir Karpinsky @ 2001-04-17 9:44 UTC (permalink / raw) To: Igor Solovyov Hello Igor, Monday, April 16, 2001, 6:35:52 PM, you wrote: IS> Hi! IS> On Mon, 16 Apr 2001 15:19:00 +0400 IS> Sergey Krivulja <skrivulja@erec.ru> wrote: >> IS>> RAID-0 это не зеркалирование, а просто объединение нескольких >> IS>> дисков в один. А вот RAID-1 - зеркалирование. >> IS>> Кстати, на этих мамах есть возможность сделать RAID-0+1. >> SK> Так это стандартная фича для IDE контроллеров. >> Извиняюсь за неточность. Я имею ввиду, что доп. контроллеры >> именно в таком исполнении ставят RAID-0+1. IS> Э.... Не очень понял о чем речь. Там есть возможность выбрать одно IS> из трех: RAID-0, RAID-1 или RAID-0+1. (Для HPT-370 во всяком случае). Прости за невежество, а что такое 0+1. Порознь понятно: объединение и зеркалирование, а вот что получается вместе? -- Best regards, Vladimir mailto:vkarpinsky@beep.ru From cornet@zmail.ru Tue Apr 17 09:45:35 2001 Return-Path: <cornet@zmail.ru> Delivered-To: mandrake-russian@localhost.ru.net Received: from frontend1.aha.ru (fish.zenon.net [213.189.198.214]) by linux.ru.net (Postfix) with ESMTP id 6433EDC8 for <mandrake-russian@altlinux.ru>; Tue, 17 Apr 2001 09:45:35 +0400 (MSD) Received: from [195.2.83.130] (HELO backend2.aha.ru) by frontend1.aha.ru (CommuniGate Pro SMTP 3.4.4) with ESMTP id 92047368 for mandrake-russian@altlinux.ru; Tue, 17 Apr 2001 09:46:57 +0400 Received: from [195.210.132.242] (account cornet@zmail.ru HELO zmail.ru) by backend2.aha.ru (CommuniGate Pro SMTP 3.4.4) with ESMTP id 40698719 for mandrake-russian@altlinux.ru; Tue, 17 Apr 2001 09:46:46 +0400 Message-ID: <3ADBD901.BEEDB64E@zmail.ru> From: cornet <cornet@zmail.ru> X-Mailer: Mozilla 4.7 [en] (X11; I; Linux 2.2.14-15mdk i686) X-Accept-Language: ru, en MIME-Version: 1.0 To: mandrake-russian@altlinux.ru Subject: Re: [mdk-re] Re: [mdk-re] =?koi8-r?Q?=EE=CF=D7=D9=CA?= KDE References: <3ADA9DF9.E19D289B@zmail.ru> <20010416233307.558473b1.sass@uustoll.ee> Content-Type: text/plain; charset=koi8-r Content-Transfer-Encoding: 8bit Sender: mandrake-russian-admin@altlinux.ru Errors-To: mandrake-russian-admin@altlinux.ru X-BeenThere: mandrake-russian@altlinux.ru X-Mailman-Version: 2.0 Precedence: bulk Reply-To: mandrake-russian@altlinux.ru List-Help: <mailto:mandrake-russian-request@altlinux.ru?subject=help> List-Post: <mailto:mandrake-russian@altlinux.ru> List-Subscribe: <http://altlinux.ru/mailman/listinfo/mandrake-russian>, <mailto:mandrake-russian-request@altlinux.ru?subject=subscribe> List-Id: Mandrake/RE discussion list <mandrake-russian.altlinux.ru> List-Unsubscribe: <http://altlinux.ru/mailman/listinfo/mandrake-russian>, <mailto:mandrake-russian-request@altlinux.ru?subject=unsubscribe> List-Archive: <http://altlinux.ru/pipermail/mandrake-russian/> Date: Tue Apr 17 09:46:00 2001 X-Original-Date: Tue, 17 Apr 2001 09:47:45 +0400 Aleksandr Blohin wrote: > > On Mon, 16 Apr 2001 11:23:37 +0400 > cornet <cornet@zmail.ru> wrote: > > C> Hello, всем :-)) > C> > C> Че то новый KDE из Спринга ни как не хочет у меня принимать вид > прежнего > C> из RE7.0 а я так к нему привык уже :-(( > C> > C> А именно, у меня основная_пенель сидит наверху, а панель_задач слева > C> вверху и выезжает. То есть картинка на экране с выехавшими задачами > C> аттачет. Когда смотрел Сизифа, то изрядно порывшись по настроечкам > нашел > C> в свойствах панели_задач параметр слева-вверху, но гайка за него > C> отвечающая была не активная :-( > C> Думал, что в релизе в обновленном KDE эту гайку наконец то > активизируют, > C> ан нет :-(( ее теперь вообще нету! Облом. > C> > C> Или я просто не нашел? > C> > C> А в KDE нынешнего вида я жить отказываюсь, неудобно :-( просто хоть на > C> другой виндоуманагер пересаживайся!! А так все было классно под Мерлина > C> заточено, так ведь нет - переделали! > C> :-(((((( > > Эх! > Знали бы Вы! > Сколько горьких слёз я пролил из-за отсутствия слева-вверху с выездом :-) Представляю сколько, сам горюю :-(( это была ИМХО одна из самых рульных интерфейсных фишек KDE! Ну нафига им потребовалось все это переделывать!! Была отличная оригинальная концепция, а теперь, все это стало очень походить на Гном (я ничего не хочу сказать плохого про Гном), а прелесть как раз была в _разных_концепциях_, а теперь имеем два виндоуменеджера разных по дизайну и либам и очень похожих функционально!! Спрашивается - и нафига нам два раза одно и то же? Обидно :-((( -- ******** FIRE & STEEL ******** ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: Re[7]: [mdk-re] HPT370 2001-04-17 9:44 ` Vladimir Karpinsky @ 2001-04-17 17:51 ` Lenya L.Khachaturov 2001-04-17 19:21 ` Re[9]: " Vladimir Karpinsky 0 siblings, 1 reply; 27+ messages in thread From: Lenya L.Khachaturov @ 2001-04-17 17:51 UTC (permalink / raw) To: mandrake-russian On Tue, 17 Apr 2001 09:43:54 +0400 Vladimir Karpinsky <vkarpinsky@beep.ru> wrote: > Hello Igor, > > Monday, April 16, 2001, 6:35:52 PM, you wrote: > > IS> Hi! > IS> On Mon, 16 Apr 2001 15:19:00 +0400 > IS> Sergey Krivulja <skrivulja@erec.ru> wrote: > > >> IS>> RAID-0 это не зеркалирование, а просто объединение нескольких > >> IS>> дисков в один. А вот RAID-1 - зеркалирование. > >> IS>> Кстати, на этих мамах есть возможность сделать RAID-0+1. > >> SK> Так это стандартная фича для IDE контроллеров. > >> Извиняюсь за неточность. Я имею ввиду, что доп. контроллеры > >> именно в таком исполнении ставят RAID-0+1. > > IS> Э.... Не очень понял о чем речь. Там есть возможность выбрать одно > IS> из трех: RAID-0, RAID-1 или RAID-0+1. (Для HPT-370 во всяком случае). > > Прости за невежество, а что такое 0+1. Порознь понятно: объединение и > зеркалирование, а вот что получается вместе? Объединение + зеркалирование, для этого нужны 4 винта ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re[9]: [mdk-re] HPT370 2001-04-17 17:51 ` Lenya L.Khachaturov @ 2001-04-17 19:21 ` Vladimir Karpinsky 2001-04-17 20:34 ` Igor Solovyov 0 siblings, 1 reply; 27+ messages in thread From: Vladimir Karpinsky @ 2001-04-17 19:21 UTC (permalink / raw) To: Lenya L.Khachaturov Hello Lenya, Tuesday, April 17, 2001, 5:00:51 PM, you wrote: >> Прости за невежество, а что такое 0+1. Порознь понятно: объединение и >> зеркалирование, а вот что получается вместе? LLK> Объединение + зеркалирование, для этого нужны 4 винта Т.е. одна пара зеркалирует другую? А вообще, какие требования при зеркалировании на тип (UDMAхх) и размеры? -- Best regards, Vladimir mailto:vkarpinsky@beep.ru From is13@inbox.ru Tue Apr 17 19:26:02 2001 Return-Path: <is13@inbox.ru> Delivered-To: mandrake-russian@localhost.ru.net Received: from mx5.port.ru (mx5.port.ru [194.67.23.40]) by linux.ru.net (Postfix) with ESMTP id C50F0BDD for <mandrake-russian@altlinux.ru>; Tue, 17 Apr 2001 19:26:02 +0400 (MSD) Received: from hearst.int ([10.0.0.103] helo=hearst.port.ru) by mx5.port.ru with esmtp (Exim 3.14 #3) id 14pXNz-000C7e-00 for mandrake-russian@altlinux.ru; Tue, 17 Apr 2001 19:27:23 +0400 Received: from [213.242.63.20] (helo=private.zlt.ru) by hearst.port.ru with smtp (Exim 3.14 #3) id 14pXNx-0006rQ-00 for mandrake-russian@altlinux.ru; Tue, 17 Apr 2001 19:27:22 +0400 From: Igor Solovyov <is13@inbox.ru> To: mandrake-russian@altlinux.ru Subject: Re: [mdk-re] VMWare Message-Id: <20010417212718.31b8c219.is13@inbox.ru> In-Reply-To: <Pine.LNX.4.33L.0104171713140.1936-100000@zephyrous.ru> References: <20010417003526.0001f2e0.is13@inbox.ru> <Pine.LNX.4.33L.0104171713140.1936-100000@zephyrous.ru> X-Mailer: Sylpheed version 0.4.62 (GTK+ 1.2.9; i586-mandrake-linux) Organization: Private person Mime-Version: 1.0 Content-Type: text/plain; charset=KOI8-R Content-Transfer-Encoding: 8bit Sender: mandrake-russian-admin@altlinux.ru Errors-To: mandrake-russian-admin@altlinux.ru X-BeenThere: mandrake-russian@altlinux.ru X-Mailman-Version: 2.0 Precedence: bulk Reply-To: mandrake-russian@altlinux.ru List-Help: <mailto:mandrake-russian-request@altlinux.ru?subject=help> List-Post: <mailto:mandrake-russian@altlinux.ru> List-Subscribe: <http://altlinux.ru/mailman/listinfo/mandrake-russian>, <mailto:mandrake-russian-request@altlinux.ru?subject=subscribe> List-Id: Mandrake/RE discussion list <mandrake-russian.altlinux.ru> List-Unsubscribe: <http://altlinux.ru/mailman/listinfo/mandrake-russian>, <mailto:mandrake-russian-request@altlinux.ru?subject=unsubscribe> List-Archive: <http://altlinux.ru/pipermail/mandrake-russian/> Date: Tue Apr 17 19:27:00 2001 X-Original-Date: Tue, 17 Apr 2001 21:27:18 +0600 Hi! On Tue, 17 Apr 2001 17:18:00 +0400 (MSD) Ivan Zakharyaschev <imz@linux.ru.net> wrote: > Hello! > > On Tue, 17 Apr 2001, Igor Solovyov wrote: > > > Исправил на kgcc. Все то же самое. Модуль компилится, но: > > ....... > > /root/tmp/vmware-config0/vmnet.o: unresolved symbol skb_datarefp > > There is probably a light difference of kernel........ > > А Вы случайно не обновлялись apt, не глядя на то, что сиавится? Ядра она > сама не доустанавливает (по apt-get upgrade), а вот > kernel-{headers,source,doc} обновляет. Отсюда может и возникнуть > несоответствие. Нет, не обновлялся. -- Best regards! Igor Solovyov Zlatoust, Russia ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: Re[9]: [mdk-re] HPT370 2001-04-17 19:21 ` Re[9]: " Vladimir Karpinsky @ 2001-04-17 20:34 ` Igor Solovyov 2001-04-18 10:15 ` Re[11]: " Vladimir Karpinsky 0 siblings, 1 reply; 27+ messages in thread From: Igor Solovyov @ 2001-04-17 20:34 UTC (permalink / raw) To: mandrake-russian Hi! On Tue, 17 Apr 2001 19:21:01 +0400 Vladimir Karpinsky <vkarpinsky@beep.ru> wrote: > Hello Lenya, > > Tuesday, April 17, 2001, 5:00:51 PM, you wrote: > > >> Прости за невежество, а что такое 0+1. Порознь понятно: объединение и > >> зеркалирование, а вот что получается вместе? > > LLK> Объединение + зеркалирование, для этого нужны 4 винта > > Т.е. одна пара зеркалирует другую? А вообще, какие требования при > зеркалировании на тип (UDMAхх) и размеры? Да в общем-то никаких особенных. Чем номер УДМА больше, тем Вам же лучше. :-))))) А что касается размеров... :-))), то в общем-то современные HDD имеют примерно одинаковый размер (145х105х25 мм) :-))))))) А если говорить про емкость - то то же, чем больше тем лучше. Но только имейте в виду следуещее. Если использовать контроллер HPT-370, то никакой диагностики Вы не получите. Т.е. если, например, одна половина зеркала выйдет из строя, то Вам об этом никто не сообщит. Именно это и является самым главным недостатком HPT-370. В ответственных случаях лучше взять RAID-контроллер посерьезней. -- Best regards! Igor Solovyov Zlatoust, Russia ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re[11]: [mdk-re] HPT370 2001-04-17 20:34 ` Igor Solovyov @ 2001-04-18 10:15 ` Vladimir Karpinsky 2001-04-18 13:01 ` Robert Kochtchenkov 0 siblings, 1 reply; 27+ messages in thread From: Vladimir Karpinsky @ 2001-04-18 10:15 UTC (permalink / raw) To: Igor Solovyov Hello Igor, Tuesday, April 17, 2001, 8:34:34 PM, you wrote: >> Т.е. одна пара зеркалирует другую? А вообще, какие требования при >> зеркалировании на тип (UDMAхх) и размеры? IS> Да в общем-то никаких особенных. Чем номер УДМА больше, тем Вам же IS> лучше. :-))))) А что касается размеров... :-))), то в общем-то IS> современные HDD имеют примерно одинаковый размер (145х105х25 мм) IS> :-))))))) А если говорить про емкость - то то же, чем больше тем IS> лучше. Я не правильно сформулировал вопрос. А имел ввиду я следующее: должны ли быть зеркалированные (ух слово-то какое) винчестеры одинаковые, точнее насколько одинаковые? А про то, сто лучше быть здоровым и богатым, а не наоборот я уже знаю :). IS> Но только имейте в виду следуещее. Если использовать IS> контроллер HPT-370, то никакой диагностики Вы не получите. Т.е. IS> если, например, одна половина зеркала выйдет из строя, то Вам об IS> этом никто не сообщит. Именно это и является самым главным IS> недостатком HPT-370. В ответственных случаях лучше взять IS> RAID-контроллер посерьезней. Спасибо за предупреждение. -- Best regards, Vladimir mailto:vkarpinsky@beep.ru From vkarpinsky@beep.ru Wed Apr 18 10:18:56 2001 Return-Path: <vkarpinsky@beep.ru> Delivered-To: mandrake-russian@localhost.ru.net Received: from beep.ru (www.beep.ru [212.188.13.192]) by linux.ru.net (Postfix) with SMTP id A0DBEE7B for <mandrake-russian@altlinux.ru>; Wed, 18 Apr 2001 10:18:56 +0400 (MSD) Received: from 195.201.30.245 by beep.ru with SMTP id AA08765 for mandrake-russian@altlinux.ru; Wed, 18 Apr 2001 10:20:09 +0400 (MSD) From: Vladimir Karpinsky <vkarpinsky@beep.ru> X-Mailer: The Bat! (v1.51) Business Organization: Seismology Lab X-Priority: 3 (Normal) Message-ID: <272342591.20010418100743@beep.ru> To: "Anton I . Danilov" <mandrake-russian@altlinux.ru> Subject: Re[4]: [mdk-re] Full Duplex 100 Mhz for Realtek8139 In-Reply-To: <20010417092427.0853ea18.savara@yandex.ru> References: <Pine.LNX.4.33L.0104141653370.2825-100000@energy.forge><3ADA9777.C5446E9E@zmail.ru> <3510083553.20010416110253@erec.ru> <006201c0c6fd$cdc48d90$0500000a@sasha> <20010417092427.0853ea18.savara@yandex.ru> MIME-Version: 1.0 Content-Type: text/plain; charset=koi8-r Content-Transfer-Encoding: 8bit Content-Length: 482 Sender: mandrake-russian-admin@altlinux.ru Errors-To: mandrake-russian-admin@altlinux.ru X-BeenThere: mandrake-russian@altlinux.ru X-Mailman-Version: 2.0 Precedence: bulk Reply-To: mandrake-russian@altlinux.ru X-Reply-To: Vladimir Karpinsky <vkarpinsky@beep.ru> List-Help: <mailto:mandrake-russian-request@altlinux.ru?subject=help> List-Post: <mailto:mandrake-russian@altlinux.ru> List-Subscribe: <http://altlinux.ru/mailman/listinfo/mandrake-russian>, <mailto:mandrake-russian-request@altlinux.ru?subject=subscribe> List-Id: Mandrake/RE discussion list <mandrake-russian.altlinux.ru> List-Unsubscribe: <http://altlinux.ru/mailman/listinfo/mandrake-russian>, <mailto:mandrake-russian-request@altlinux.ru?subject=unsubscribe> List-Archive: <http://altlinux.ru/pipermail/mandrake-russian/> Date: Wed Apr 18 10:19:12 2001 X-Original-Date: Wed, 18 Apr 2001 10:07:43 +0400 Hello Anton, Tuesday, April 17, 2001, 9:24:27 AM, you wrote: >> Linux). Потом их переставил - под Win она сразу распозналась как >> "графическая карта, но не VGA". После этого я ее снес в магазин и >> обменял. AID> Я сегодня их буду менять на 3com SOHO. Сообщите пожалуйста о результатах ее установки под Спринг. А то я про нее слышал, что это чуть ли не вин-сетевая карта. -- Best regards, Vladimir mailto:vkarpinsky@beep.ru ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: Re[11]: [mdk-re] HPT370 2001-04-18 10:15 ` Re[11]: " Vladimir Karpinsky @ 2001-04-18 13:01 ` Robert Kochtchenkov 2001-04-18 17:37 ` Igor Solovyov 0 siblings, 1 reply; 27+ messages in thread From: Robert Kochtchenkov @ 2001-04-18 13:01 UTC (permalink / raw) To: mandrake-russian > Я не правильно сформулировал вопрос. А имел ввиду я следующее: должны > ли быть зеркалированные (ух слово-то какое) винчестеры одинаковые, > точнее насколько одинаковые? Если винты разные, то возникает ряд проблем, правда не смертельных. Как-то - если разные размеры, то зеркалированный массив получается размером с меньший диск (избыточная часть пространства большего диска просто пропадает, если конечно, райд железный - справедливо для контроллера Promise FT66) а если разные скорости работы, то массив работает со скоростью самого медленного диска. С уважением, Роберт. ^ permalink raw reply [flat|nested] 27+ messages in thread
* Re: Re[11]: [mdk-re] HPT370 2001-04-18 13:01 ` Robert Kochtchenkov @ 2001-04-18 17:37 ` Igor Solovyov 0 siblings, 0 replies; 27+ messages in thread From: Igor Solovyov @ 2001-04-18 17:37 UTC (permalink / raw) To: mandrake-russian Hi! On Wed, 18 Apr 2001 12:00:13 +0300 "Robert Kochtchenkov" <robert@baltnet.ru> wrote: > > > > Я не правильно сформулировал вопрос. А имел ввиду я следующее: должны > > ли быть зеркалированные (ух слово-то какое) винчестеры одинаковые, > > точнее насколько одинаковые? > > Если винты разные, то возникает ряд проблем, правда не смертельных. Как-то - > если разные размеры, то зеркалированный массив получается размером с меньший > диск (избыточная часть пространства большего диска просто пропадает, если > конечно, райд железный - справедливо для контроллера Promise FT66) а если > разные скорости работы, то массив работает со скоростью самого медленного > диска. Аналогично и для HPT-370 -- Best regards! Igor Solovyov Zlatoust, Russia ^ permalink raw reply [flat|nested] 27+ messages in thread
end of thread, other threads:[~2001-04-18 17:37 UTC | newest] Thread overview: 27+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2001-04-12 10:10 [mdk-re] HPT370 Maxim Savrilov 2001-04-12 10:21 ` Anton Farygin 2001-04-12 10:22 ` Yura Zotov 2001-04-12 18:30 ` Igor Solovyov 2001-04-12 18:38 ` Yura Zotov 2001-04-12 19:59 ` Igor Solovyov 2001-04-12 20:51 ` Yura Zotov 2001-04-12 22:21 ` Igor Solovyov 2001-04-13 0:10 ` Yura Zotov 2001-04-13 15:46 ` Igor Solovyov 2001-04-13 21:30 ` Yura Zotov 2001-04-13 22:53 ` Igor Solovyov 2001-04-13 23:03 ` Igor Solovyov 2001-04-14 11:27 ` Re[2]: " Sergey Krivulja 2001-04-14 11:40 ` Igor Solovyov 2001-04-16 14:05 ` Re[4]: " Sergey Krivulja 2001-04-16 15:19 ` Re[5]: " Sergey Krivulja 2001-04-16 18:35 ` Igor Solovyov 2001-04-17 8:43 ` Re[7]: " Sergey Krivulja 2001-04-17 19:57 ` Igor Solovyov 2001-04-17 9:44 ` Vladimir Karpinsky 2001-04-17 17:51 ` Lenya L.Khachaturov 2001-04-17 19:21 ` Re[9]: " Vladimir Karpinsky 2001-04-17 20:34 ` Igor Solovyov 2001-04-18 10:15 ` Re[11]: " Vladimir Karpinsky 2001-04-18 13:01 ` Robert Kochtchenkov 2001-04-18 17:37 ` Igor Solovyov
ALT Linux Community general discussions This inbox may be cloned and mirrored by anyone: git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 community community/ http://lore.altlinux.org/community \ mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com public-inbox-index community Example config snippet for mirrors. Newsgroup available over NNTP: nntp://lore.altlinux.org/org.altlinux.lists.community AGPL code for this site: git clone https://public-inbox.org/public-inbox.git