* [mdk-re] Modem @ 2001-03-26 11:52 Alting 2001-03-26 14:44 ` Sergey Vlasov 0 siblings, 1 reply; 6+ messages in thread From: Alting @ 2001-03-26 11:52 UTC (permalink / raw) To: MANDRAKE-RUSSIAN Здравствуйте! Присоединяюсь к поздравления по поводу выхода нового дистрибутива! И небольшой вопрос: Есть модем внутренний Sportser 33600. На MDK 7.0RE работал как часы, а вот на оригинальном 7.2 при попытке сделать ifup ppp0 пишет в логах: modprobe: modprobe: can't locate module char-major-108 connect script filed. Сразу оговорюсь, что по kudzu модем не определился никак. Я ставил его и PnP и строго на Com2 (или Com1). Ничего не помогает. PnP-ISA конфигурить не умею... Как справиться с проблемой? -- With best regards mailto:alting@mail.ru ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [mdk-re] Modem 2001-03-26 11:52 [mdk-re] Modem Alting @ 2001-03-26 14:44 ` Sergey Vlasov 2001-03-27 9:53 ` Re[2]: " Alting 0 siblings, 1 reply; 6+ messages in thread From: Sergey Vlasov @ 2001-03-26 14:44 UTC (permalink / raw) To: mandrake-russian On Mon, 26 Mar 2001 11:54:55 +0400 Alting <alting@mail.ru> wrote: > Здравствуйте! > > Присоединяюсь к поздравления по поводу выхода нового дистрибутива! > > И небольшой вопрос: > Есть модем внутренний Sportser 33600. > На MDK 7.0RE работал как часы, а вот на оригинальном 7.2 при попытке > сделать ifup ppp0 пишет в логах: > modprobe: modprobe: can't locate module char-major-108 > connect script filed. > > Сразу оговорюсь, что по kudzu модем не определился никак. Я ставил > его и PnP и строго на Com2 (или Com1). Ничего не помогает. > PnP-ISA конфигурить не умею... > Как справиться с проблемой? А при установке на Com2 (или Com1) на материнке соответствующий порт через BIOS отключен? Если порты нужны, насколько я помню, можно выставить COM3, IRQ5 или 9, но в этом случае нужно в /etc/rc.d/rc.serial написать соответствующий вызов setserial, и опять же прописать в BIOS для соответствующего IRQ, что он на Legacy ISA. С PnP-ISA лучше не связываться. После этого проверить через minicom, отвечает модем или нет. Если отвечает - надо смотреть настройки в /etc/sysconfig/network-scripts. ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re[2]: [mdk-re] Modem 2001-03-26 14:44 ` Sergey Vlasov @ 2001-03-27 9:53 ` Alting 2001-03-27 11:23 ` Sviatoslav Sviridov 2001-03-27 20:17 ` Re[2]: " Sergey Vlasov 0 siblings, 2 replies; 6+ messages in thread From: Alting @ 2001-03-27 9:53 UTC (permalink / raw) To: Sergey Vlasov Здравствуйте! Monday, March 26, 2001, 1:59:40 PM, you wrote: SV> On Mon, 26 Mar 2001 11:54:55 +0400 SV> Alting <alting@mail.ru> wrote: >> Здравствуйте! >> >> Присоединяюсь к поздравления по поводу выхода нового дистрибутива! >> >> И небольшой вопрос: >> Есть модем внутренний Sportser 33600. >> На MDK 7.0RE работал как часы, а вот на оригинальном 7.2 при попытке >> сделать ifup ppp0 пишет в логах: >> modprobe: modprobe: can't locate module char-major-108 >> connect script filed. >> >> Сразу оговорюсь, что по kudzu модем не определился никак. Я ставил >> его и PnP и строго на Com2 (или Com1). Ничего не помогает. >> PnP-ISA конфигурить не умею... >> Как справиться с проблемой? SV> А при установке на Com2 (или Com1) на материнке соответствующий порт через BIOS отключен? Если порты нужны, насколько я помню, можно выставить COM3, IRQ5 или 9, но в этом случае нужно в SV> /etc/rc.d/rc.serial написать соответствующий вызов setserial, и опять же прописать в BIOS для соответствующего IRQ, что он на Legacy ISA. С PnP-ISA лучше не связываться. SV> После этого проверить через minicom, отвечает модем или нет. Если отвечает - надо смотреть настройки в /etc/sysconfig/network-scripts. SV> _______________________________________________ SV> Mandrake-russian mailing list SV> Mandrake-russian@linuxteam.iplabs.ru SV> http://altlinux.ru/mailman/listinfo/mandrake-russian Еще раз всем здравствуйте ;) Спасибо всем, кто помог мне по теме Switch Managament. Проблема действительно оказалась тривиальной и все заработало на ура. Теперь к модему: он так и не заработал, хотя я обнаружил, что kudzu по умолчанию в 7.2, в отличие от 7.0RE НЕ ОПРАШИВАЕТ serial порты. Как только эту опцию отключил, kudzu бодро отрапортовал, что, мол, есть такая буква, то бишь, модем, в данном наборе девайсов. Правда работать модем все равно отказался, но возникла следующая чертовски неприятная проблема: компьютер не грузится до конца. По моему, эту тему уже обсуждали, напомните, плиз.... Симптомы такие: после старта определенного кол-ва сервисов (причем не знаю какого именно - не догадался посчитать), после очередного ОК все встает колом. НИЧЕГО РОВНЫМ СЧЕТОМ НЕ ПРОИСХОДИТ. Как будто машина висит. Причем, если отказаться от загрузки демона, на котором машина стопорится - она застопорится на следующем... Если отказаться от запуска демонов вообще (в интерактивном режиме), машина нормально доходит до логина. Можно залогироваться и позапускать все руками - будет работать. Если умудриться запустить не все демоны и добраться до логина - залогироваться можно а дальше тишина и мертвые с косами... никакого приглашения командной строки - вообще ни чего (runlevel 3). Еще симптом - похоже syslogd не стартует - на 12 консоли ничего; попробовал выводить все логи сразу на первую - раньще при старте демонов уже начинали сыпаться логи. Сейчас - полная тишина... Стартуешь syslog руками - все едет как ни в чем не бывало... В чем может быть проблема? Как починить можно? P.S. Вспомнил еще одну подробность - заработала PnPISA. Пишет ОК, вот только, если у меня модем стоит например на 3Е8 - то эта самая пнписа конфигурит модем на любой другой порт, кроме этого. Может, ее вообще убить? Вот только как? Может из-за нее такие глюки наступили? Извините за длинное и подробное изложение. -- With best regards mailto:alting@mail.ru ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Re[2]: [mdk-re] Modem 2001-03-27 9:53 ` Re[2]: " Alting @ 2001-03-27 11:23 ` Sviatoslav Sviridov 2001-03-28 11:21 ` Re[4]: " Alting 2001-03-27 20:17 ` Re[2]: " Sergey Vlasov 1 sibling, 1 reply; 6+ messages in thread From: Sviatoslav Sviridov @ 2001-03-27 11:23 UTC (permalink / raw) To: mandrake-russian On Tue, 27 Mar 2001 09:57:39 +0400 Alting <alting@mail.ru> wrote: > Симптомы такие: после старта определенного кол-ва сервисов (причем не > знаю какого именно - не догадался посчитать), после очередного ОК все > встает колом. НИЧЕГО РОВНЫМ СЧЕТОМ НЕ ПРОИСХОДИТ. Как будто машина > висит. Причем, если отказаться от загрузки демона, на котором машина > стопорится - она застопорится на следующем... > Если отказаться от запуска демонов вообще (в интерактивном режиме), > машина нормально доходит до логина. Можно залогироваться и позапускать > все руками - будет работать. Если умудриться запустить не все демоны и > добраться до логина - залогироваться можно а дальше тишина и мертвые с > косами... никакого приглашения командной строки - вообще ни чего > (runlevel 3). > Еще симптом - похоже syslogd не стартует - на 12 консоли ничего; > попробовал выводить все логи сразу на первую - раньще при старте > демонов уже начинали сыпаться логи. Сейчас - полная тишина... > Стартуешь syslog руками - все едет как ни в чем не бывало... > > В чем может быть проблема? Как починить можно? Похоже, что именно в syslog'e и есть проблема. У меня тоже такое было как-то после обновления из сизифа. syslog просто не запускался при старте машины. Починить просто: # chkconfig --level 2345 syslog on -- Sviatoslav Sviridov [mailto:svd@lintec.minsk.by] [ICQ#10845380] [Lintec Project] [MLUG] ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re[4]: [mdk-re] Modem 2001-03-27 11:23 ` Sviatoslav Sviridov @ 2001-03-28 11:21 ` Alting 0 siblings, 0 replies; 6+ messages in thread From: Alting @ 2001-03-28 11:21 UTC (permalink / raw) To: Sviatoslav Sviridov Здравствуйте! Tuesday, March 27, 2001, 11:27:46 AM, you wrote: SS> On Tue, 27 Mar 2001 09:57:39 +0400 SS> Alting <alting@mail.ru> wrote: >> Симптомы такие: после старта определенного кол-ва сервисов (причем не >> знаю какого именно - не догадался посчитать), после очередного ОК все >> встает колом. НИЧЕГО РОВНЫМ СЧЕТОМ НЕ ПРОИСХОДИТ. Как будто машина >> висит. Причем, если отказаться от загрузки демона, на котором машина >> стопорится - она застопорится на следующем... >> Если отказаться от запуска демонов вообще (в интерактивном режиме), >> машина нормально доходит до логина. Можно залогироваться и позапускать >> все руками - будет работать. Если умудриться запустить не все демоны и >> добраться до логина - залогироваться можно а дальше тишина и мертвые с >> косами... никакого приглашения командной строки - вообще ни чего >> (runlevel 3). >> Еще симптом - похоже syslogd не стартует - на 12 консоли ничего; >> попробовал выводить все логи сразу на первую - раньще при старте >> демонов уже начинали сыпаться логи. Сейчас - полная тишина... >> Стартуешь syslog руками - все едет как ни в чем не бывало... >> >> В чем может быть проблема? Как починить можно? SS> Похоже, что именно в syslog'e и есть проблема. У меня SS> тоже такое было как-то после обновления из сизифа. SS> syslog просто не запускался при старте машины. SS> Починить просто: SS> # chkconfig --level 2345 syslog on Получилось!!!! Огромное спасибо Вам, Святослав! Обязательно возьму на заметку. -- With best regards mailto:alting@mail.ru ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Re[2]: [mdk-re] Modem 2001-03-27 9:53 ` Re[2]: " Alting 2001-03-27 11:23 ` Sviatoslav Sviridov @ 2001-03-27 20:17 ` Sergey Vlasov 1 sibling, 0 replies; 6+ messages in thread From: Sergey Vlasov @ 2001-03-27 20:17 UTC (permalink / raw) To: mandrake-russian On Tue, 27 Mar 2001 09:57:39 +0400 Alting <alting@mail.ru> wrote: > P.S. Вспомнил еще одну подробность - заработала PnPISA. Пишет ОК, вот > только, если у меня модем стоит например на 3Е8 - то эта самая пнписа > конфигурит модем на любой другой порт, кроме этого. Может, ее вообще > убить? Вот только как? Может из-за нее такие глюки наступили? Если модем позволяет - лучше убрать. Мне вот, например, попалась один раз такая карточка, которая распознавалась isapnp (да и BIOS тоже) через раз. Нужно убрать /etc/isapnp.conf, тогда isapnp запускаться не будет. А модем настроить перемычками как надо. Если прерывание нестандартное - прописать в /etc/rc.d/rc.serial (или где там ее новый rc.sysinit ищет) вызов setserial с нужными параметрами (хотя это и в случае isapnp нужно). ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2001-03-28 11:21 UTC | newest] Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2001-03-26 11:52 [mdk-re] Modem Alting 2001-03-26 14:44 ` Sergey Vlasov 2001-03-27 9:53 ` Re[2]: " Alting 2001-03-27 11:23 ` Sviatoslav Sviridov 2001-03-28 11:21 ` Re[4]: " Alting 2001-03-27 20:17 ` Re[2]: " Sergey Vlasov
ALT Linux Community general discussions This inbox may be cloned and mirrored by anyone: git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 community community/ http://lore.altlinux.org/community \ mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com public-inbox-index community Example config snippet for mirrors. Newsgroup available over NNTP: nntp://lore.altlinux.org/org.altlinux.lists.community AGPL code for this site: git clone https://public-inbox.org/public-inbox.git