From: Yuriy Gomenyuk <All-yvg@ukr.net>
To: "\"Бессонов Ян\"" <community@altlinux.ru>
Subject: [Comm] Re: [Comm] Re: [Comm] S3 Pro Savage K133 и иксы
Date: Thu, 9 Jan 2003 16:16:05 +0300
Message-ID: <159367738.20030109161605@ukr.net> (raw)
In-Reply-To: <007001c2b7c7$234514e0$056409c0@LocalHost>
Здравствуйте, Бессонов.
Вы писали 9 января 2003 г., 13:09:03:
>> Сейчас я во Львове, устанавливаю для людей (общественная организация)
>> Junior 2.0.
>>
>> Прошу помощи:
>>
>> Всё было хорошо, но под конец инсталятор выдал какую то ошибку (что то
>> с графикой, точно не помню...)
>>
>> При запуске всё идёт нормально до загрузки иксов - монитор несколько
>> раз мигает, и иксы так и не появляются (остаётся приглашение на ввод
>> юзера и пароля, после которого можно работать в терминальном
>> режиме...)
>>
>> Видео карта встроенная на материнке -
>> S3 Graphics Pro Savage
>> микросхема: (8Mb)
>>
>>
>> К сожалению не помню в каком файле смотреть сообщения об ошибках.
>> Пожалуйста подскажите....
???
БЯ> Запусти startx почитай ошибки, у тебя похоже драйвера нет, либо с
БЯ> настройками XConfiga надо поиграть ---- запусти ещё lspci
вот что выдаёт lspci:
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 81)
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06)
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16)
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16)
00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
00:07.5 Multimedia audio controller: VIA Technologies, Inc. AC97 Audio Controller (rev 50)
00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
01:00.0 VGA compatible controller: S3 Inc. ProSavage KM133
Вот что выдаёт startx:
(Файл xdm-errors.log)
***
XFree86 Version 3.3.6a / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: April 19, 2001
If the server is older than 6-12 months, or if your card is newer
than the above date, look for a newer version before reporting
problems. (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.4.18-alt0.1.pre4-smp i686 [ELF]
Configured drivers:
SVGA: server for SVGA graphics adaptors (Patchlevel 1):
s3_savage, NV1, STG2000, RIVA 128, RIVA TNT, RIVA TNT2,
RIVA ULTRA TNT2, RIVA VANTA, RIVA ULTRA VANTA, RIVA INTEGRATED,
GeForce 256, GeForce DDR, Quadro, GeForce2 GTS, GeForce2 GTS (rev1),
GeForce2 Ultra, Quadro 2 Pro, GeForce2 MX, GeForce2 MX DDR,
Quadro 2 MXR, ET4000, ET4000W32, ET4000W32i, ET4000W32i_rev_b,
ET4000W32i_rev_c, ET4000W32p, ET4000W32p_rev_a, ET4000W32p_rev_b,
ET4000W32p_rev_c, ET4000W32p_rev_d, ET6000, ET6100, et3000, pvga1,
wd90c00, wd90c10, wd90c30, wd90c24, wd90c31, wd90c33, gvga, r128, ati,
sis86c201, sis86c202, sis86c205, sis86c215, sis86c225, sis5597,
sis5598, sis6326, sis530, sis620, sis300, sis630, sis540, tvga8200lx,
tvga8800cs, tvga8900b, tvga8900c, tvga8900cl, tvga8900d, tvga9000,
tvga9000i, tvga9100b, tvga9200cxr, tgui9400cxi, tgui9420, tgui9420dgi,
tgui9430dgi, tgui9440agi, cyber9320, tgui9660, tgui9680, tgui9682,
tgui9685, cyber9382, cyber9385, cyber9388, cyber9397, cyber9520,
cyber9525, 3dimage975, 3dimage985, cyber9397dvd, blade3d, cyberblade,
clgd5420, clgd5422, clgd5424, clgd5426, clgd5428, clgd5429, clgd5430,
clgd5434, clgd5436, clgd5446, clgd5480, clgd5462, clgd5464, clgd5465,
clgd6205, clgd6215, clgd6225, clgd6235, clgd7541, clgd7542, clgd7543,
clgd7548, clgd7555, clgd7556, ncr77c22, ncr77c22e, cpq_avga, mga2064w,
mga1064sg, mga2164w, mga2164w AGP, mgag200, mgag100, mgag400, oti067,
oti077, oti087, oti037c, al2101, ali2228, ali2301, ali2302, ali2308,
ali2401, cl6410, cl6412, cl6420, cl6440, video7, ark1000vl, ark1000pv,
ark2000pv, ark2000mt, mx, realtek, s3_virge, AP6422, AT24, AT3D,
s3_svga, NM2070, NM2090, NM2093, NM2097, NM2160, NM2200, ct65520,
ct65525, ct65530, ct65535, ct65540, ct65545, ct65546, ct65548,
ct65550, ct65554, ct65555, ct68554, ct69000, ct64200, ct64300,
mediagx, V1000, V2100, V2200, p9100, spc8110, i740, i740_pci,
Voodoo Banshee, Voodoo3, i810, i810-dc100, i810e, i815, smi, generic
(using VT number 7)
XF86Config: /etc/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: keycodes: "xfree86"
(**) XKB: types: "default"
(**) XKB: compat: "default"
(**) XKB: symbols: "us(pc105)"
(**) XKB: geometry: "pc"
(**) XKB: rules: "xfree86"
(**) XKB: model: "pc105"
(**) XKB: layout: "ru"
(**) XKB: variant: "winkeys"
(**) XKB: options: "grp:ctrl_toggle"
(**) Mouse: type: PS/2, device: /dev/psaux, buttons: 3
(**) Mouse: 3 button emulation (timeout: 50ms)
(**) SVGA: Graphics device ID: "S3 Savage4"
(**) SVGA: Monitor ID: "monitor1"
(--) SVGA: Mode "1600x1200" needs hsync freq of 87.50 kHz. Deleted.
(--) SVGA: Mode "1152x864" needs hsync freq of 89.62 kHz. Deleted.
(--) SVGA: Mode "1280x1024" needs hsync freq of 91.15 kHz. Deleted.
(--) SVGA: Mode "1600x1200" needs hsync freq of 93.75 kHz. Deleted.
(--) SVGA: Mode "1600x1200" needs hsync freq of 105.77 kHz. Deleted.
(--) SVGA: Mode "1600x1200" needs hsync freq of 106.25 kHz. Deleted.
(--) SVGA: Mode "1280x1024" needs hsync freq of 107.16 kHz. Deleted.
(--) SVGA: Mode "1800X1440" needs hsync freq of 96.15 kHz. Deleted.
(--) SVGA: Mode "1800X1440" needs hsync freq of 104.52 kHz. Deleted.
(--) SVGA: Mode "1920x1440" needs hsync freq of 90.00 kHz. Deleted.
(--) SVGA: Mode "1920x1440" needs hsync freq of 112.50 kHz. Deleted.
(**) FontPath set to "unix/:-1"
(--) SVGA: PCI: S3 Unknown chipset (0x8a26) rev 0, Memory @ 0xdd000000, 0xd0000000
(--) SVGA: Unknown S3 chipset: chip_id = 0x8a26 rev. 0
(--) SVGA: chipset: generic
(--) SVGA: videoram: 64k
(--) SVGA: clocks: 25.18
(**) SVGA: 32bpp not supported for this chipset
*** A configured device found, but display modes could not be resolved.***
Fatal server error:
no screens found
When reporting a problem related to a server crash, please send
the full server output, not just the last messages
xdm error (pid 1737): IO Error in XOpenDisplay
xdm error (pid 1566): Display :0 cannot be opened
xdm error (pid 1566): Display :0 is being disabled
***
БЯ> но не всегда --- с ATIRadeon не поможет
БЯ> Ян
>>
>>
>>
>> В X86Config-4 графика прописана так:
>>
>> *
>> # Graphics device section
>> # **********************************************************************
>>
>> Section "Device"
>> Identifier "Generic VGA"
>> Driver "vga"
>> EndSection
>>
>> Section "Device"
>> Identifier "S3 Savage4"
>> VendorName "Unknown"
>> BoardName "Unknown"
>> Driver "savage"
>> # VideoRam 8192
>> # Clock lines
>>
>>
>> # Uncomment following option if you see a big white block
>> # instead of the cursor!
>> # Option "sw_cursor"
>>
>> Option "DPMS" "on"
>> EndSection
>>
>>
>>
>> # *********************************************
>>
>>
>> P.S. Чайником как был так и остался (тем более что все письма
>> конференции и т.д. остались в родном городе), при запросе уточняющей
>> информации указывать каким образом её "получить"...
--
С уважением,
Yuriy mailto:All-yvg@ukr.net
next prev parent reply other threads:[~2003-01-09 13:16 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-01-09 8:52 Yuriy Gomenyuk
2003-01-09 10:09 ` [Comm] " Бессонов Ян
2003-01-09 13:16 ` Yuriy Gomenyuk [this message]
2003-01-09 14:28 ` [Comm] " Artem Pastukhov
2003-01-09 13:37 ` [Comm] Re[2]: " Yuriy Gomenyuk
2003-01-09 14:46 ` Artem Pastukhov
2003-01-09 17:55 ` [Comm] Re[2]: " Yuriy Gomenyuk
2003-01-09 15:01 ` [Comm] " Бессонов Ян
2003-01-09 14:45 ` [Comm] " Бессонов Ян
2003-01-09 15:06 ` Artem Pastukhov
2003-01-09 15:13 ` [Comm] " Бессонов Ян
2003-01-09 14:28 ` Бессонов Ян
2003-01-09 13:44 ` [Comm] " Yuriy Gomenyuk
2003-01-09 14:30 ` Andriy Dobrovol's'kii
2003-01-09 13:45 ` [Comm] " Yuriy Gomenyuk
2003-01-09 15:00 ` [Comm] " Andriy Dobrovol's'kii
2003-01-09 14:41 ` Someone Unknown
2003-01-09 18:00 ` [Comm] Re[2]: " Yuriy Gomenyuk
2003-01-10 2:01 ` [Comm] " Michael Shigorin
2003-01-10 2:58 ` [Comm] Re: [Comm] Re: [Comm] " Eugene
2003-01-10 2:00 ` [Comm] " Michael Shigorin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=159367738.20030109161605@ukr.net \
--to=all-yvg@ukr.net \
--cc=community@altlinux.ru \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
ALT Linux Community general discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
public-inbox-index community
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.community
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git