Re: [mdk-re] XFree86 for mach64

["Ruslan" <rusl@comset.net>]

 Hi!
> > Ищу самый свежий mach64 сервер, чтобы заработала наконец моя видяха.
> > Вручную настроить параметры "не по зубам", но, говорят, что в новых
версиях
> > учтены баги старых.
> >
> А в чём проблема? Я использую mach64 на двух разных картах Rage II+ и Rage
Pro
> на XFree начиная с 3.3.3 и вплоть до последнего 4.0.3 b и не испытываю
никаких
> трудностей. Совсем никаких.

А у меня черный экран. Как только startx'ишся, так сразу все падает.
На http://www.xfree86.org/3.3.6/ati6.html написано, что так и надо....
У меня  вот какая видяха : ATI-264GT2PLUS - TEKRAM M250 -ATI  Rage
II-3D-mach64

Можно попросить прислать/дать ссылочку на 4.0.3 b для mach64 , а также Ваш
XF86Config?
Спасибо!

Из моего autologin.log:
Operating System: Linux 2.2.17-16mdksmp i686 [ELF]
Configured drivers:
  Mach64: accelerated server for ATI Mach64 graphics adaptors (Patchlevel 1)
(using VT number 7)
XF86Config: /etc/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: disabled
(**) XKB: keycodes: "xfree86"
(**) XKB: types: "default"
(**) XKB: compat: "default"
(**) XKB: symbols: "us(pc105)"
(**) XKB: geometry: "pc"
(**) XKB: rules: "xfree86"
(**) XKB: model: "pc105"
(**) XKB: layout: ""
(**) Mouse: type: IMPS/2, device: /dev/psaux, buttons: 5
(**) Mouse: zaxismapping: (-)4 (+)5
(**) Mach64: Graphics device ID: "ATI Mach64 3D RAGE II"
(**) Mach64: Monitor ID: "Generic|SVGA Высокой Частоты, 1024x768 при 70 Hz"
(--) Mach64: Mode "640x480" needs vert refresh rate of 100.02 Hz. Deleted.
(--) Mach64: Mode "800x600" needs hsync freq of 64.02 kHz. Deleted.
(--) Mach64: Mode "1024x768" needs hsync freq of 62.50 kHz. Deleted.
(--) Mach64: Mode "1152x864" needs hsync freq of 62.42 kHz. Deleted.
(--) Mach64: Mode "1280x1024" needs hsync freq of 64.25 kHz. Deleted.
(--) Mach64: Mode "1024x768" needs hsync freq of 70.24 kHz. Deleted.
(--) Mach64: Mode "1152x864" needs hsync freq of 70.88 kHz. Deleted.
(--) Mach64: Mode "1280x1024" needs hsync freq of 74.59 kHz. Deleted.
(--) Mach64: Mode "1600x1200" needs hsync freq of 75.00 kHz. Deleted.
(--) Mach64: Mode "1152x864" needs hsync freq of 76.01 kHz. Deleted.
(--) Mach64: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted.
(--) Mach64: Mode "1024x768" needs hsync freq of 80.21 kHz. Deleted.
(--) Mach64: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted.
(--) Mach64: Mode "1600x1200" needs hsync freq of 87.50 kHz. Deleted.
(--) Mach64: Mode "1152x864" needs hsync freq of 89.62 kHz. Deleted.
(--) Mach64: Mode "1280x1024" needs hsync freq of 91.15 kHz. Deleted.
(--) Mach64: Mode "1600x1200" needs hsync freq of 93.75 kHz. Deleted.
(--) Mach64: Mode "1600x1200" needs hsync freq of 105.77 kHz. Deleted.
(--) Mach64: Mode "1280x1024" needs hsync freq of 107.16 kHz. Deleted.
(--) Mach64: Mode "1800X1440" needs hsync freq of 96.15 kHz. Deleted.
(--) Mach64: Mode "1800X1440" needs hsync freq of 104.52 kHz. Deleted.
(**) FontPath set to "unix/:-1"
(--) Mach64: PCI: Mach64 GT rev 154, Aperture @ 0xe4000000, Registers @
0xe6000000, Block I/O @ 0xe400
(**) Mach64: Option "power_saver"
(--) Mach64: Card type: PCI
(--) Mach64: Memory type: EDO (2)
(--) Mach64: Clock type: Internal
(--) Mach64: Maximum allowed dot-clock: 200.000 MHz
(**) Mach64: Mode "800x600": mode clock =  60.750
(--) Mach64: Illegal mode according to Mach64 BIOS
(--) Mach64: Removing mode "800x600" from list of valid modes.
(**) Mach64: Mode "640x480": mode clock =  36.000
(--) Mach64: Virtual resolution: 640x480
(--) Mach64: Video RAM: 2048k
(--) Mach64: Using hardware cursor
(--) Mach64: Using 16 MB aperture @ 0xe4000000
(--) Mach64: Using 4 KB register aperture @ 0xe6000000
(--) Mach64: Ramdac is Internal
(--) Mach64: Ramdac speed: 200 MHz
Mach64: Cannot read colourmap from VGA.  Will restore with default
(--) Mach64: Pixmap cache: 0 256x256 slots, 0 128x128 slots, 0 64x64 slots
(--) Mach64: Font cache: 0 fonts
x128 slots, 0 64x64 slots
(--) Mach64: Font cache: 0 fonts

--
Sayonara,
Ruslan
St. Petersburg, Russia
ruslan@mail.ru
ICQ: 12331863