From: Alexander Bokovoy <ab@altlinux.org>
To: ALT Linux Sisyphus discussions <sisyphus@lists.altlinux.org>
Subject: Re: [sisyphus] Desktop Personal & Lite (20071018)
Date: Sat, 20 Oct 2007 14:01:10 +0400
Message-ID: <4719D1E6.8000805@altlinux.org> (raw)
In-Reply-To: <4719A945.2020001@altlinux.org>
[-- Attachment #1: Type: text/plain, Size: 1797 bytes --]
Alexander Bokovoy пишет:
> Michael Shigorin пишет:
>> On Sat, Oct 20, 2007 at 10:51:50AM +0400, Alexander Bokovoy wrote:
>>>>> Я не знаю, на каком устройстве хватало 128М, но тут очевидно не
>>>>> хватает.
>>>> Саш, я на 64M проверял -- устанавливается.
>>> Миша, не важно, где ты проверял
>> Это может быть важно для диагностики.
>>
>> 20071018 тащу.
> Положил altinst (он меньше на 4Мб),full.cz и vmlinuz от ALD4.0, никакой
> разницы -- также не хватает места при распаковке в ramdisk.
>
Продолжение. Вместе с rider@ добрались до разбивки диска:
1. Грузим ядро с automatic=method:disk lowmem xdriver=intel
2. Выбираем необходимые пути для загрузки с диске (sdc, sdc1, /)
3. Получаем инсталятор.
Теперь при разбивке диска проблема: инсталятор хочет перечитать таблицы,
в том числе и на диске, с которого он работает. Это не проходит (раздел
смонтирован), поэтому дальше пройти нельзя.
Итого, требуется исправить работу инсталятора, чтобы он учитывал в
режиме method:disk, что с диском, _с_которого_ идет установка, все равно
ничего сделать нельзя и поэтому не пытался его как-то трогать. Или
вообще не показывать в редакторе разделов, если можно определить, что
этот диск -- USB Flash.
И еще одно: Видимо, для NAND Flash лучше не ext2, а JFFS2, может быть
имеет смысл добавить ее поддержку в инсталятор, обвесив кучей
напоминаний, что это только для встроенных NAND-flash (USB flash имеет
свою встроенную систему распределения секторов, предназначенную для
борьбы с изнашиванием).
Прикладываю lspci -vv, lspci -n и dmesg с Intel ClassmatePC.
--
/ Alexander Bokovoy
Samba Team http://www.samba.org/
ALT Linux Team http://www.altlinux.org/
Midgard Project Ry http://www.midgard-project.org/
[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 15554 bytes --]
Linux version 2.6.18-std-smp-alt8 (builder@hint1.office.altlinux.org) (gcc version 4.1.1 20070105 (ALT Linux, build 4.1.1-alt11)) #1 SMP Mon Sep 24 01:41:06 MSD 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000f7c0000 (usable)
BIOS-e820: 000000000f7c0000 - 000000000f7ce000 (ACPI data)
BIOS-e820: 000000000f7ce000 - 000000000f800000 (ACPI NVS)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fed13000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
247MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 63424
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 59328 pages, LIFO batch:15
DMI 2.3 present.
ACPI: RSDP (v002 ACPIAM ) @ 0x000f8ef0
ACPI: XSDT (v001 A M I OEMXSDT 0x03000702 MSFT 0x00000097) @ 0x0f7c0100
ACPI: FADT (v003 A M I OEMFACP 0x03000702 MSFT 0x00000097) @ 0x0f7c0290
ACPI: MADT (v001 A M I OEMAPIC 0x03000702 MSFT 0x00000097) @ 0x0f7c0390
ACPI: MCFG (v001 A M I OEMMCFG 0x03000702 MSFT 0x00000097) @ 0x0f7c03f0
ACPI: OEMB (v001 A M I AMI_OEM 0x03000702 MSFT 0x00000097) @ 0x0f7ce040
ACPI: MCFG (v001 A M I OEMMCFG 0x03000702 MSFT 0x00000097) @ 0x0f7c38c0
ACPI: TCPA (v001 A M I TBLOEMID 0x00000001 MSFT 0x00000097) @ 0x0f7c3900
ACPI: DSDT (v001 eduwi eduwi001 0x00000001 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 10000000 (gap: 0f800000:d0800000)
Detected 897.861 MHz processor.
Built 1 zonelists. Total pages: 63424
Kernel command line: initrd=alt0/full.cz changedisk lang=ru_RU automatic=method:disk splash=silent splashcount=17 showopts lowmem xdriver=intel BOOT_IMAGE=alt0/vmlinuz
bootsplash: silent mode.
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 243660k/253696k available (1585k kernel code, 9528k reserved, 640k data, 192k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1797.33 BogoMIPS (lpj=3594666)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
checking if image is initramfs... it is
Freeing initrd memory: 4108k freed
ACPI: Core revision 20060707
ACPI: Looking for DSDT in initramfs... /DSDT.aml does not exist.
CPU0: Intel(R) Celeron(R) M processor 900MHz stepping 08
Total of 1 processors activated (1797.33 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
ACPI: 2 duplicate MCFG table ignored.
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: Embedded Controller [EC0] (gpe 24) interrupt mode.
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1e.0
IO window: e000-efff
MEM window: feb00000-febfffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1192887312.892:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.0.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
NET: Registered protocol family 1
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 192k freed
Time: tsc clocksource has been installed.
Executing init=/init
input: AT Translated Set 2 keyboard as /class/input/input0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 169, io mem 0xfea3bc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usb 1-2: new high speed USB device using ehci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
usb 1-4: new high speed USB device using ehci_hcd and address 4
usb 1-4: configuration #1 chosen from 1 choice
usb 1-6: new high speed USB device using ehci_hcd and address 5
usb 1-6: configuration #1 chosen from 1 choice
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 169, io base 0x0000d880
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 177, io base 0x0000d800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 185, io base 0x0000d480
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 193, io base 0x0000d400
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 185
ICH6: chipset revision 4
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio
Probing IDE interface ide0...
libata version 2.00 loaded.
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 P2 -- -- ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xC880 ctl 0xC802 bmdma 0xC080 irq 177
ata2: SATA max UDMA/133 cmd 0xC480 ctl 0xC402 bmdma 0xC088 irq 177
scsi0 : ata_piix
ATA: abnormal status 0x7F on port 0xC887
scsi1 : ata_piix
ATA: abnormal status 0x7F on port 0xC487
usbcore: registered new driver libusual
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
scsi4 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
Vendor: M-Sys Model: uDiskOnChip Rev: 5.u7
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 3997183 512-byte hdwr sectors (2047 MB)
sda: Write Protect is off
sda: Mode Sense: 2b 00 00 00
sda: assuming drive cache: write through
Vendor: Generic Model: STORAGE DEVICE Rev: 9404
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 3997183 512-byte hdwr sectors (2047 MB)
sda: Write Protect is off
sda: Mode Sense: 2b 00 00 00
sda: assuming drive cache: write through
sda: sda1 sda2
sd 4:0:0:0: Attached scsi disk sda
sd 2:0:0:0: Attached scsi removable disk sdb
usb-storage: device scan complete
usb-storage: device scan complete
Vendor: JetFlash Model: TS2GJFV30 Rev: 8.07
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdc: 4005886 512-byte hdwr sectors (2051 MB)
sdc: Write Protect is off
sdc: Mode Sense: 03 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 4005886 512-byte hdwr sectors (2051 MB)
sdc: Write Protect is off
sdc: Mode Sense: 03 00 00 00
sdc: assuming drive cache: write through
sdc: sdc1
sd 3:0:0:0: Attached scsi removable disk sdc
usb-storage: device scan complete
loop: loaded (max 8 devices)
squashfs: version 3.2 (2007/01/02) Phillip Lougher
Registering unionfs 1.4
unionfs: debugging is not enabled
sd 4:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: Attached scsi generic sg1 type 0
sd 3:0:0:0: Attached scsi generic sg2 type 0
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
8139cp 0000:01:02.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:01:02.0: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 18 (level, low) -> IRQ 185
eth0: RealTek RTL8139 at 0xd00c2c00, 00:03:0d:5d:32:a0, IRQ 185
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 177
input: PC Speaker as /class/input/input1
Real Time Clock Driver v1.12ac
tpm_inf_pnp 00:0a: Found TPM with ID IFX0102
tpm_inf_pnp 00:0a: TPM found: config base 0x4e, io base 0x4700, chip version 0x000b, vendor id 0x15d1 (Infineon), product id 0x000b (SLB 9635 TT 1.2)
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x39a0b2, caps: 0xa04753/0x200000
input: SynPS/2 Synaptics TouchPad as /class/input/input2
ts: Compaq touchscreen protocol output
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
SCSI device sda: 3997183 512-byte hdwr sectors (2047 MB)
sda: Write Protect is off
sda: Mode Sense: 2b 00 00 00
sda: assuming drive cache: write through
sda: sda1 sda2
usb 1-8: new high speed USB device using ehci_hcd and address 6
usb 1-8: configuration #1 chosen from 1 choice
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
Vendor: JetFlash Model: TS1GJF120 Rev: 8.07
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdd: 2047998 512-byte hdwr sectors (1049 MB)
sdd: Write Protect is off
sdd: Mode Sense: 03 00 00 00
sdd: assuming drive cache: write through
SCSI device sdd: 2047998 512-byte hdwr sectors (1049 MB)
sdd: Write Protect is off
sdd: Mode Sense: 03 00 00 00
sdd: assuming drive cache: write through
sdd: sdd1
sd 5:0:0:0: Attached scsi removable disk sdd
sd 5:0:0:0: Attached scsi generic sg3 type 0
usb-storage: device scan complete
[-- Attachment #3: lspci-n.txt --]
[-- Type: text/plain, Size: 462 bytes --]
00:00.0 0600: 8086:2590 (rev 04)
00:02.0 0300: 8086:2592 (rev 04)
00:1d.0 0c03: 8086:2658 (rev 04)
00:1d.1 0c03: 8086:2659 (rev 04)
00:1d.2 0c03: 8086:265a (rev 04)
00:1d.3 0c03: 8086:265b (rev 04)
00:1d.7 0c03: 8086:265c (rev 04)
00:1e.0 0604: 8086:2448 (rev d4)
00:1e.2 0401: 8086:266e (rev 04)
00:1f.0 0601: 8086:2641 (rev 04)
00:1f.1 0101: 8086:266f (rev 04)
00:1f.2 0101: 8086:2653 (rev 04)
00:1f.3 0c05: 8086:266a (rev 04)
01:02.0 0200: 10ec:8139 (rev 10)
[-- Attachment #4: lspci-vv.txt --]
[-- Type: text/plain, Size: 8163 bytes --]
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 04)
Subsystem: Uniwill Computer Corp Unknown device 9810
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04) (prog-if 00 [VGA])
Subsystem: Uniwill Computer Corp Unknown device 9810
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fea80000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at dc00 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at fea40000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04) (prog-if 00 [UHCI])
Subsystem: Uniwill Computer Corp Unknown device 906a
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 169
Region 4: I/O ports at d880 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04) (prog-if 00 [UHCI])
Subsystem: Uniwill Computer Corp Unknown device 906a
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 177
Region 4: I/O ports at d800 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04) (prog-if 00 [UHCI])
Subsystem: Uniwill Computer Corp Unknown device 906a
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 185
Region 4: I/O ports at d480 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04) (prog-if 00 [UHCI])
Subsystem: Uniwill Computer Corp Unknown device 906a
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 193
Region 4: I/O ports at d400 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04) (prog-if 20 [EHCI])
Subsystem: Uniwill Computer Corp Unknown device 906a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 169
Region 0: Memory at fea3bc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Uniwill Computer Corp Unknown device 906a
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 04)
Subsystem: Uniwill Computer Corp Unknown device 906a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 3
Region 0: I/O ports at d000 [size=256]
Region 1: I/O ports at cc00 [size=64]
Region 2: Memory at fea3b800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at fea3b400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 04)
Subsystem: Uniwill Computer Corp Unknown device 906a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 04) (prog-if 8a [Master SecP PriP])
Subsystem: Uniwill Computer Corp Unknown device 906a
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 185
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at ffa0 [size=16]
00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 04) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Uniwill Computer Corp Unknown device 906a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 177
Region 0: I/O ports at c880 [size=8]
Region 1: I/O ports at c800 [size=4]
Region 2: I/O ports at c480 [size=8]
Region 3: I/O ports at c400 [size=4]
Region 4: I/O ports at c080 [size=16]
Region 5: Memory at fea3b000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04)
Subsystem: Uniwill Computer Corp Unknown device 906a
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 177
Region 4: I/O ports at 0400 [size=32]
01:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Uniwill Computer Corp Unknown device 906a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 185
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at febffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
next prev parent reply other threads:[~2007-10-20 10:01 UTC|newest]
Thread overview: 47+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-10-19 8:39 Anton V. Boyarshinov
2007-10-20 5:56 ` Alexander Bokovoy
2007-10-20 6:15 ` Владимир Черный
2007-10-20 6:23 ` Alexander Bokovoy
2007-10-20 6:37 ` Alexander Bokovoy
2007-10-20 6:46 ` Michael Shigorin
2007-10-20 6:51 ` Alexander Bokovoy
2007-10-20 6:56 ` Michael Shigorin
2007-10-20 7:07 ` Alexander Bokovoy
2007-10-20 8:37 ` Anton Farygin
2007-10-20 9:08 ` Alexander Bokovoy
2007-10-20 11:58 ` Michael Shigorin
2007-10-20 10:01 ` Alexander Bokovoy [this message]
2007-10-20 10:24 ` Dmitry V. Levin
2007-10-20 10:36 ` Alexander Bokovoy
2007-10-20 8:36 ` Anton Farygin
2007-10-20 8:36 ` Anton Farygin
2007-10-20 10:17 ` Alexander Bokovoy
2007-10-20 10:19 ` Dmitry V. Levin
2007-10-20 10:28 ` Alexander Bokovoy
2007-10-20 6:50 ` Alexander Bokovoy
2007-10-20 8:38 ` Anton Farygin
2007-10-20 9:58 ` Sergey Bolshakov
2007-10-20 10:34 ` Alexander Bokovoy
2007-10-20 11:04 ` Anton Farygin
2007-10-20 9:42 ` Sergey Vlasov
2007-10-20 10:46 ` Alexander Bokovoy
2007-10-20 11:05 ` Anton Farygin
2007-10-20 11:35 ` Vladimir A. Svyatoshenko
2007-10-20 12:40 ` Alexander Bokovoy
2007-10-20 16:16 ` Anton Farygin
2007-10-20 16:59 ` Alexander Bokovoy
2007-10-20 18:15 ` Anton Farygin
2007-10-20 19:58 ` Sergey Vlasov
2007-10-20 22:16 ` Alexander Bokovoy
2007-10-21 8:50 ` Sergey Vlasov
2007-10-21 9:28 ` Alexander Bokovoy
2007-10-21 13:03 ` Sergey Vlasov
2007-10-21 13:11 ` Alexander Bokovoy
2007-10-21 12:03 ` Michael Shigorin
2007-10-21 12:09 ` Alexander Bokovoy
2007-10-21 12:42 ` Valery V. Inozemtsev
2007-10-21 12:45 ` Michael Shigorin
2007-10-21 13:00 ` Valery V. Inozemtsev
2007-10-21 16:41 ` Andrey Rahmatullin
2007-10-21 17:14 ` Valery V. Inozemtsev
2007-10-20 19:34 ` Michael Shigorin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4719D1E6.8000805@altlinux.org \
--to=ab@altlinux.org \
--cc=sisyphus@lists.altlinux.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
ALT Linux Sisyphus discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/sisyphus/0 sisyphus/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 sisyphus sisyphus/ http://lore.altlinux.org/sisyphus \
sisyphus@altlinux.ru sisyphus@altlinux.org sisyphus@lists.altlinux.org sisyphus@lists.altlinux.ru sisyphus@lists.altlinux.com sisyphus@linuxteam.iplabs.ru sisyphus@list.linux-os.ru
public-inbox-index sisyphus
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.sisyphus
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git