From: Lortonix <lortonix@gmail.com>
To: Saratov Linux User Group Maillist <sarlug@lists.lug.ru>
Subject: [Sarlug] Вопрос о USB.
Date: Fri, 11 Sep 2009 21:45:00 +0400
Message-ID: <29521e040909111045j1af54f4bq3ff2cf492640c006@mail.gmail.com> (raw)
Здравствуйте!
Вопрос такой, при подключении внешнего винта через USB он не
определяется правильно. А при подключении флешек все работает.
Дистрибутив - Ubuntu Karmic Koala (development branch).
:~$ dmesg
[31560.606232] scsi9 : SCSI emulation for USB Mass Storage devices
[31560.612054] usb-storage: device found at 10
[31560.612058] usb-storage: waiting for device to settle before scanning
[31565.612236] usb-storage: device scan complete
[31565.612716] scsi 9:0:0:0: Direct-Access ST916031 0AS
PQ: 0 ANSI: 2 CCS
[31565.613248] sd 9:0:0:0: Attached scsi generic sg2 type 0
[31565.646075] sd 9:0:0:0: [sdb] 312581808 512-byte logical blocks:
(160 GB/149 GiB)
[31565.646817] sd 9:0:0:0: [sdb] Write Protect is off
[31565.646822] sd 9:0:0:0: [sdb] Mode Sense: 34 00 00 00
[31565.646825] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[31565.649195] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[31565.649201] sdb:
[31565.684078] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[31565.684086] sd 9:0:0:0: [sdb] Attached SCSI disk
[31565.892027] usb 1-3: reset high speed USB device using ehci_hcd and
address 10
[31566.028053] usb 1-3: device descriptor read/64, error -71
[31566.268031] usb 1-3: device descriptor read/64, error -71
[31566.484032] usb 1-3: reset high speed USB device using ehci_hcd and
address 10
[31566.620029] usb 1-3: device descriptor read/64, error -71
[31566.860028] usb 1-3: device descriptor read/64, error -71
[31567.076032] usb 1-3: reset high speed USB device using ehci_hcd and
address 10
[31567.500020] usb 1-3: device not accepting address 10, error -71
[31567.612032] usb 1-3: reset high speed USB device using ehci_hcd and
address 10
[31573.032036] usb 1-3: device not accepting address 10, error -110
[31573.032087] sd 9:0:0:0: Device offlined - not ready after error recovery
[31573.035638] usb 1-3: USB disconnect, address 10
[31573.152037] usb 1-3: new high speed USB device using ehci_hcd and address 11
[31573.288030] usb 1-3: device descriptor read/64, error -71
[31573.528053] usb 1-3: device descriptor read/64, error -71
[31573.744340] usb 1-3: new high speed USB device using ehci_hcd and address 12
[31573.880032] usb 1-3: device descriptor read/64, error -71
[31574.120030] usb 1-3: device descriptor read/64, error -71
[31574.336055] usb 1-3: new high speed USB device using ehci_hcd and address 13
[31574.760021] usb 1-3: device not accepting address 13, error -71
[31574.872030] usb 1-3: new high speed USB device using ehci_hcd and address 14
[31575.296069] usb 1-3: device not accepting address 14, error -71
[31575.296095] hub 1-0:1.0: unable to enumerate USB device on port 3
[31575.628055] usb 3-1: new full speed USB device using ohci_hcd and address 6
[31575.768027] usb 3-1: device descriptor read/64, error -62
[31576.020037] usb 3-1: device descriptor read/64, error -62
[31576.260035] usb 3-1: new full speed USB device using ohci_hcd and address 7
[31576.400029] usb 3-1: device descriptor read/64, error -62
[31576.644261] usb 3-1: device descriptor read/64, error -62
[31576.884030] usb 3-1: new full speed USB device using ohci_hcd and address 8
[31577.292016] usb 3-1: device not accepting address 8, error -62
[31577.428059] usb 3-1: new full speed USB device using ohci_hcd and address 9
[31577.840782] usb 3-1: device not accepting address 9, error -62
[31577.840848] hub 3-0:1.0: unable to enumerate USB device on port 1
В энторнетах предлагают отрубить модуль ehci_hcd, но
:~$ sudo modprobe -r ehci_hcd
FATAL: Module ehci_hcd not found.
Проблема конкретной в моем дистрибутиве, загружался с лайфсиди и
подключал - работает, на других компах также все нормально.
Загружался на других версиях ядра, но результата это не дало.
Есть идеи?
--
С уважением, Lortonix!
next reply other threads:[~2009-09-11 17:45 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-09-11 17:45 Lortonix [this message]
2009-09-11 18:07 ` Lortonix
2009-09-11 18:16 ` Eugene Horohorin
2009-09-11 18:18 ` Lortonix
2009-09-11 18:17 ` Alexander Burachewkij
2009-09-11 18:19 ` Eugene Horohorin
2009-09-11 18:25 ` [Sarlug] ADSL Alexander Burachewkij
2009-09-11 18:21 ` [Sarlug] Вопрос о USB Lortonix
2009-09-12 17:19 ` Яков Попов
2009-09-12 18:00 ` Lortonix
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=29521e040909111045j1af54f4bq3ff2cf492640c006@mail.gmail.com \
--to=lortonix@gmail.com \
--cc=sarlug@lists.lug.ru \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Saratov Linux User Group
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/sarlug/0 sarlug/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 sarlug sarlug/ http://lore.altlinux.org/sarlug \
sarlug@lists.lug.ru sarlug@lug.ru
public-inbox-index sarlug
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.sarlug
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git