From: Andrei Lomov <lomov@math.nsc.ru> To: hardware@lists.altlinux.org Subject: [Hardware] smartctl Date: Wed, 16 Jan 2008 17:11:05 +0600 Message-ID: <fmkoo9$gm5$1@ger.gmane.org> (raw) С жестким диском, похоже, нелады ... Пока работает, но диагностика подозрительная. Посоветуйте, насколько это критично, сейчас бежать в магазин, или еще потерпит? # /usr/sbin/smartctl -a /dev/hda smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: ST3250823A Serial Number: 5ND0RV7P Firmware Version: 3.03 Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Wed Jan 16 17:05:07 2008 NOVT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 84) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 058 054 006 Pre-fail Always - 24580178 3 Spin_Up_Time 0x0003 099 098 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1688 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 077 060 030 Pre-fail Always - 51790101 9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 4559 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1716 194 Temperature_Celsius 0x0022 039 048 000 Old_age Always - 39 (Lifetime Min/Max 0/15) 195 Hardware_ECC_Recovered 0x001a 058 053 000 Old_age Always - 24580178 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 83 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 83 occurred at disk power-on lifetime: 3659 hours (152 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 52 4d 36 e0 Error: UNC at LBA = 0x00364d52 = 3558738 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 d8 08 4f 4d 36 e0 00 00:00:49.697 READ DMA EXT 25 d8 01 d6 24 01 e0 00 00:00:49.685 READ DMA EXT 25 d8 08 4f 4d 36 e0 00 00:00:49.685 READ DMA EXT 25 d8 01 c8 d3 60 e0 00 00:00:49.684 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:00:49.677 READ DMA EXT Error 82 occurred at disk power-on lifetime: 3659 hours (152 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 52 4d 36 e0 Error: UNC at LBA = 0x00364d52 = 3558738 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 d8 08 4f 4d 36 e0 00 00:00:49.697 READ DMA EXT 25 d8 01 c8 d3 60 e0 00 00:00:49.685 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:00:49.685 READ DMA EXT 25 d8 01 00 00 00 e0 00 00:00:49.684 READ DMA EXT 25 d8 20 81 1b 09 e0 00 00:00:49.677 READ DMA EXT Error 81 occurred at disk power-on lifetime: 3659 hours (152 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 52 4d 36 e0 Error: UNC at LBA = 0x00364d52 = 3558738 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 d8 08 4f 4d 36 e0 00 00:00:45.943 READ DMA EXT 25 d8 08 ef 99 1c e0 00 00:00:45.941 READ DMA EXT 25 d8 08 e7 99 1c e0 00 00:00:45.940 READ DMA EXT 25 d8 08 47 ea 08 e0 00 00:00:45.933 READ DMA EXT 25 d8 08 3f ea 08 e0 00 00:00:45.922 READ DMA EXT Error 80 occurred at disk power-on lifetime: 3641 hours (151 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 52 4d 36 e0 Error: UNC at LBA = 0x00364d52 = 3558738 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 d8 08 4f 4d 36 e0 00 01:04:18.094 READ DMA EXT 25 d8 40 21 18 0b e0 00 01:04:18.093 READ DMA EXT 25 d8 3d 59 1b 0b e0 00 01:04:18.092 READ DMA EXT 35 d8 08 3f 6f 71 e0 00 01:04:18.092 WRITE DMA EXT 25 d8 20 9a 1b 0b e0 00 01:04:18.092 READ DMA EXT Error 79 occurred at disk power-on lifetime: 3641 hours (151 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 52 4d 36 e0 Error: UNC at LBA = 0x00364d52 = 3558738 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 d8 08 4f 4d 36 e0 00 01:03:46.319 READ DMA EXT 25 d8 18 df 6c 0a e0 00 01:03:46.314 READ DMA EXT 35 d8 08 0f 53 0a e0 00 01:03:46.314 WRITE DMA EXT 35 d8 08 1f 4f 0a e0 00 01:03:46.305 WRITE DMA EXT 35 d8 08 97 70 71 e0 00 01:03:46.305 WRITE DMA EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - # 2 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. -- Всего доброго, А.Л.
next reply other threads:[~2008-01-16 11:11 UTC|newest] Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top 2008-01-16 11:11 Andrei Lomov [this message] 2008-01-16 19:07 ` Andrey Rahmatullin 2008-01-17 15:33 ` Andrei Lomov 2008-01-17 19:20 ` Andrey Rahmatullin 2008-02-06 11:14 ` ABATAPA 2008-04-01 14:08 ` Andrei Lomov
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to='fmkoo9$gm5$1@ger.gmane.org' \ --to=lomov@math.nsc.ru \ --cc=hardware@lists.altlinux.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: link
ALT Linux hardware support This inbox may be cloned and mirrored by anyone: git clone --mirror http://lore.altlinux.org/hardware/0 hardware/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 hardware hardware/ http://lore.altlinux.org/hardware \ hardware@altlinux.ru hardware@lists.altlinux.org hardware@lists.altlinux.ru hardware@lists.altlinux.com hardware@altlinux.org public-inbox-index hardware Example config snippet for mirrors. Newsgroup available over NNTP: nntp://lore.altlinux.org/org.altlinux.lists.hardware AGPL code for this site: git clone https://public-inbox.org/public-inbox.git