Linux version 2.6.18-std-smp-alt8 (builder@hint1.office.altlinux.org) (gcc version 4.1.1 20070105 (ALT Linux, build 4.1.1-alt11)) #1 SMP Mon Sep 24 01:41:06 MSD 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
 BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
 BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 262128
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 225280 pages, LIFO batch:31
  HighMem zone: 32752 pages, LIFO batch:7
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia                                ) @ 0x000f7460
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff7b80
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Detected 1754.053 MHz processor.
Built 1 zonelists.  Total pages: 262128
Kernel command line: auto BOOT_IMAGE=ALT_Linux ro root=301 splash=silent
bootsplash: silent mode.
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1035368k/1048512k available (1585k kernel code, 12544k reserved, 640k data, 192k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3510.71 BogoMIPS (lpj=7021439)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
checking if image is initramfs... it is
Freeing initrd memory: 380k freed
ACPI: Core revision 20060707
ACPI: Looking for DSDT in initramfs... /DSDT.aml does not exist.
CPU0: AMD Sempron(tm)   2500+ stepping 01
Total of 1 processors activated (3510.71 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb500, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: nForce2 C1 Halt Disconnect fixup
Boot video device is 0000:02:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:00: ioport range 0x4200-0x427f has been reserved
pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
pnp: 00:01: ioport range 0x5000-0x503f has been reserved
PCI: Bridge: 0000:00:08.0
  IO window: d000-dfff
  MEM window: d6000000-d7ffffff
  PREFETCH window: d2000000-d2ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: disabled.
  MEM window: d3000000-d5ffffff
  PREFETCH window: c0000000-cfffffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1205834138.664:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
0000:00:02.0 OHCI: BIOS handoff failed (BIOS bug ?) 00000784
vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 6144k, total 131072k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:d600
vesafb: pmi: set display start = c00cd636, set palette = c00cd6a0
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da 
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 65745 bytes,<6>...found (1024x768, 14646 bytes, v3).
Console: switching to colour frame buffer device 125x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
NET: Registered protocol family 1
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 192k freed
Executing init=/init
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: ST320410A, ATA DISK drive
hdb: ST3160023A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(100)
hda: cache flushes not supported
 hda: hda1 hda2 hda3 < hda5 >
hdb: max request size: 512KiB
hdb: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100)
hdb: cache flushes supported
 hdb: hdb1 hdb2 < hdb5 hdb6 >
hdd: TEAC DW-552G, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input0
Real Time Clock Driver v1.12ac
Linux video capture interface: v2.00
usbcore: registered new driver usbfs
usbcore: registered new driver hub
gameport: EMU10K1 is pci0000:01:0a.1/gameport0, io 0xd800, speed 840kHz
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 177
eth0: RealTek RTL8139 at 0xf8848000, 00:80:48:36:ed:3c, IRQ 177
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, high) -> IRQ 185
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 185, io mem 0xd8000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
Linux agpgart interface v0.101 (c) Dave Jones
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 21 (level, high) -> IRQ 193
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: irq 193, io mem 0xd8001000
FDC 0 is a post-1991 82077
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 20 (level, high) -> IRQ 201
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: irq 201, io mem 0xd8002000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 32M @ 0xd0000000
ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 177
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5040
hdd: ATAPI 52X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 209
bttv0: Bt878 (rev 17) at 0000:01:08.0, irq: 209, latency: 32, mmio: 0xd2000000
bttv0: using: Lifeview FlyVideo II (Bt848) LR26 / MAXI TV Video PCI2 LR26 [card=8,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00f4ff00 [init]
bttv0: FlyVideo Radio=yes RemoteControl=yes Tuner=5 gpio=0xf4ff00
bttv0: FlyVideo  LR90=no  tda9821/tda9820=no  capture_only=no 
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
tuner 2-0061: Setting mode_mask to 0x0e
tuner 2-0061: chip found @ 0xc2 (bt878 #0 [sw])
tuner 2-0061: Calling set_type_addr for type=5, addr=0xff, mode=0x0e
tuner 2-0061: set addr for type -1
tuner 2-0061: tuner 0x61: called during i2c_client register by adapter's attach_inform
tuner 2-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
tuner 2-0061: bt878 #0 [sw] tuner I2C addr 0xc2 with type 5 used for 0x0e
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
tuner 2-0061: Cmd VIDIOC_S_STD accepted for analog TV
tuner 2-0061: switching to v4l2
tuner 2-0061: tv freq set to 400.00
tuner 2-0061: tv: param 0, range 1
tuner 2-0061: Freq= 400.00 MHz, V_IF=38.93 MHz, Offset=0.00 MHz, div=7023
tuner 2-0061: tv 0x1b 0x6f 0x8e 0x90
ohci_hcd 0000:00:02.0: wakeup
ohci_hcd 0000:00:02.1: wakeup
Adding 2097136k swap on /dev/hda2.  Priority:-1 extents:1 across:2097136k
EXT3 FS on hda1, internal journal
usb 1-1: new low speed USB device using ohci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
usb 1-2: new full speed USB device using ohci_hcd and address 4
usb 1-2: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: PS/2+USB Mouse as /class/input/input1
input: USB HID v1.10 Mouse [PS/2+USB Mouse] on usb-0000:00:02.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
/usr/src/RPM/BUILD/kernel-source-gspca-1.00.12/gspca_core.c: USB SPCA5XX camera found.(SPCA561A)
/usr/src/RPM/BUILD/kernel-source-gspca-1.00.12/gspca_core.c: [spca5xx_probe:3983] Camera type S561 
/usr/src/RPM/BUILD/kernel-source-gspca-1.00.12/gspca_core.c: [spca5xx_getcapability:1189] maxw 352 maxh 288 minw 160 minh 120
usbcore: registered new driver gspca
/usr/src/RPM/BUILD/kernel-source-gspca-1.00.12/gspca_core.c: gspca driver 01.00.12 registered
ts: Compaq touchscreen protocol output
ohci_hcd 0000:00:02.1: wakeup
usb 2-1: new low speed USB device using ohci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
input: Chicony Skype Calculator Keyboard as /class/input/input2
input: USB HID v1.11 Keyboard [Chicony Skype Calculator Keyboard] on usb-0000:00:02.1-1
input: Chicony Skype Calculator Keyboard as /class/input/input3
input,hiddev96: USB HID v1.11 Device [Chicony Skype Calculator Keyboard] on usb-0000:00:02.1-1
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!