From: Genix <genix@list.ru> To: devel-kernel@altlinux.ru Subject: [d-kernel] модуль qla2x00 Date: Wed, 20 Oct 2004 12:30:31 +0400 Message-ID: <20041020123031.1e1c2c82.genix@list.ru> (raw) Приветствую! Столкнулся со странной ситауцией, не знаю как быть и кто виноват -- прошу вашей помощи: Имеется две одинаковые серверные конфигурации, оснащенные QLA2312 Fibre Channel Adapter. Обе подключены к внешнему дисковому массиву. На одну из машин, ради эксперимента был поставлен SuSE 9.1, на другой Compact 2.3 обновленный до сизифа 20040723. В идиале, хотелось бы установить Master 2.4 на обе машины. Дисковый массив предоставляет два логичиских диска. Вот в нем-то все и дело. На SuSE видны оба раздела: QLogic Fibre Channel HBA Driver (f9097000) qla2300 0000:04:02.0: Found an ISP2312, irq 52, iobase 0xf9009000 qla2300 0000:04:02.0: Configuring PCI space... qla2300 0000:04:02.0: Configure NVRAM parameters... qla2300 0000:04:02.0: Verifying loaded RISC code... qla2300 0000:04:02.0: Waiting for LIP to complete... qla2300 0000:04:02.0: LOOP UP detected (2 Gbps). qla2300 0000:04:02.0: Topology - (N_Port-to-N_Port), Host Loop address 0x1 qla2300 0000:04:02.0: Failed SNS login: loop_id=80 mb[0]=4005 mb[1]=5 mb[2]=0 mb[6]=91 mb[7]=131 scsi1 : qla2xxx qla2300 0000:04:02.0: QLogic Fibre Channel HBA Driver: 8.00.00b11-fo QLogic QLA2340 - ISP2312: PCI-X (100 MHz) @ 0000:04:02.0 hdma-, host#=1, fw=3.02.24 IPX Vendor: SB-3160F Model: S Rev: Type: Direct-Access ANSI SCSI revision: 02 qla2300 0000:04:02.0: scsi(1:0:0:0): Enabled tagged queuing, queue depth 32. SCSI device sdc: 430112768 512-byte hdwr sectors (220218 MB) SCSI device sdc: drive cache: write back sdc: sdc1 Attached scsi disk sdc at scsi1, channel 0, id 0, lun 0 Vendor: SB-3160F Model: S Rev: Type: Direct-Access ANSI SCSI revision: 02 qla2300 0000:04:02.0: scsi(1:0:0:1): Enabled tagged queuing, queue depth 32. SCSI device sdd: 143360000 512-byte hdwr sectors (73400 MB) SCSI device sdd: drive cache: write back А на сизифе определяется только первый из них: qla2x00_set_info starts at address = f8e0e060 qla2x00: Found VID=1077 DID=2312 SSVID=1077 SSDID=100 scsi(1): Found a QLA2312 @ bus 4, device 0x2, irq 52, iobase 0x2000 scsi(1): Allocated 4096 SRB(s). scsi(1): Configure NVRAM parameters... scsi(1): 64 Bit PCI Addressing Enabled. scsi(1): Verifying loaded RISC code... scsi(1): Verifying chip... scsi(1): Waiting for LIP to complete... scsi(1): LOOP UP detected. scsi(1) qla2x00_isr MBA_PORT_UPDATE ignored scsi(1): Topology - (N_Port-to-N_Port), Host Loop address 0x1 scsi1 : QLogic QLA2312 PCI to Fibre Channel Host Adapter: bus 4 device 2 irq 52 Firmware version: 3.01.18, Driver version 6.05.00b9 blk: queue f73cca18, I/O limit 4294967295Mb (mask 0xffffffffffffffff) scsi(1): Waiting for LIP to complete... scsi(1): Topology - (N_Port-to-N_Port), Host Loop address 0x1 Vendor: SB-3160F Model: S Rev: Type: Direct-Access ANSI SCSI revision: 02 blk: queue f73cc818, I/O limit 4294967295Mb (mask 0xffffffffffffffff) scsi(1:0:0:0): Enabled tagged queuing, queue depth 32. Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0 SCSI device sdb: 430112768 512-byte hdwr sectors (220218 MB) sdb: sdb1 Еще удивило, что в SuSE загружается два драйвера для этого устройства, а в сизифе один: SuSE: lsmod | grep ql qla2300 123008 0 qla2xxx 200384 1 qla2300 scsi_mod 114372 5 st,sr_mod,qla2xxx,gdth,sd_mod ALT: lsmod | grep ql qla2300 234656 0 (unused) scsi_mod 100584 3 [qla2300 gdth sd_mod] Вопрос: 1) в чем может быть причина такого поведения и как можно ситуацию исправить? 2) как посмотреть версию модуля, чтобы сравнить ее на разных машинах? 3) На сайте qlogic есть более новая версия qla2x00, будет ли она собрана в сизиф? Поможет ли в моем случае обновление? 4) может кто знает, за что отвечает модуля qla2xxx в SuSE? -- У каждого в башке свои тараканы...
next reply other threads:[~2004-10-20 8:30 UTC|newest] Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top 2004-10-20 8:30 Genix [this message] 2004-10-21 10:24 ` Genix 2004-11-01 15:54 ` Yury Konovalov
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20041020123031.1e1c2c82.genix@list.ru \ --to=genix@list.ru \ --cc=devel-kernel@altlinux.ru \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: link
ALT Linux kernel packages development This inbox may be cloned and mirrored by anyone: git clone --mirror http://lore.altlinux.org/devel-kernel/0 devel-kernel/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 devel-kernel devel-kernel/ http://lore.altlinux.org/devel-kernel \ devel-kernel@altlinux.org devel-kernel@altlinux.ru devel-kernel@altlinux.com public-inbox-index devel-kernel Example config snippet for mirrors. Newsgroup available over NNTP: nntp://lore.altlinux.org/org.altlinux.lists.devel-kernel AGPL code for this site: git clone https://public-inbox.org/public-inbox.git