From: Kostarev Alexey <kaf@nevod.ru> To: ALT Linux Community general discussions <community@lists.altlinux.org>, ALT Linux sysadmin discuss <sysadmins@lists.altlinux.org> Subject: Re: [Comm] Пропадание интерфейса eth0 Date: Fri, 30 Nov 2007 10:07:00 +0500 Message-ID: <474F9A74.6020009@nevod.ru> (raw) In-Reply-To: <9bd187690711290703h7ba5a576j56314b63759b2e6b@mail.gmail.com> [-- Attachment #1: Type: text/plain, Size: 2633 bytes --] Andriy Dobrovol`s`kii wrote: >А если ещё порыться в логах? Может таки есть какая информация? >On Nov 29, 2007 4:39 PM, Kostarev Alexey <kaf@nevod.ru> wrote: > > >>Добрый день! >> >>На сервере были сконфигурированы два eth (eth0, eth1) интерфейса в один >>bond0 интерфейс. >> >>Сегодня перегрузили сервер и выяснилось, что eth0 не поднимается и из >>за него не встает bond0 >>(хотя вроде бы на то и bond, чтобы выручать в подобных ситуациях). >> >>Пришлось оставить в bond0 только eth1 >> >>Попытки поднять eth0 оканчиваются безуспешно >>/var/log/dmesg показывает, что система находит оба ethernet-устройства >> >>При подъеме >>ifup eth0 выводится сообщение - No such deviace >>ip link show dev eth0 >> >> >Так а ip link set ... >чем заканчивается? Может просто карточку нужно менять? > Тем же самым - не находит устройства. Карту поменять не удастся - HP Proliant - две встроенные 1GB карты. Вопрос в следующем - при работе в режиме bond обе карты, как и сам интерфейс bond имеют один и тот же физический адрес смотрим /etc/iftab: eth0 mac 00:1c:c4:a8:53:b0 eth1 mac 00:1c:c4:a8:53:b0 bond0 mac 00:1c:c4:a8:53:b0 То есть схема была eth0 --+ |---- bond0 -- eth1 ---+ При загрузке же (/var/log/dmesg) система определяет у карт два разных физических адреса (что естественно) : > Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, > 2006) > ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 185 > ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 169 > eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit > 133MHz found at mem f8000000, IRQ 185, node addr 001cc4a853b0 > ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 19 (level, low) -> IRQ 114 > PCI: Setting latency timer of device 0000:00:1d.7 to 64 > ehci_hcd 0000:00:1d.7: EHCI Host Controller > ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 6 > ehci_hcd 0000:00:1d.7: debug port 1 > PCI: cache line size of 32 is not supported by device 0000:00:1d.7 > ehci_hcd 0000:00:1d.7: irq 169, io mem 0xf7df0000 > eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit > 133MHz found at mem fa000000, IRQ 114, node addr 001cc4a853a0 001cc4a853b0 и 001cc4a853a0 соответсвенно Может быть проблема в /etc/iftab и там должны быть прописаны разные физические адреса? У кого-то есть под рукой сервер с такой конфигурацией (две eth-карты связанные в bond) Это у меня второй сервер с такой конфигурацией - до 1-го сейчас не доберусь... >>-- >>С Уважением >>Директор ООО НЕВОД >>Костарев А.Ф. >> >> >> -- С Уважением Директор ООО НЕВОД Костарев А.Ф. [-- Attachment #2: kaf.vcf --] [-- Type: text/x-vcard, Size: 202 bytes --] begin:vcard fn:Alexey Kostarev n:Kostarev;Alexey org:Nevod Ltd. adr:;;;Perm;;;Russia email;internet:kaf@nevod.ru tel;work:(3422) 196-960 url:http://www.nevod.ru/nevod/staff/kaf/ version:2.1 end:vcard
next prev parent reply other threads:[~2007-11-30 5:07 UTC|newest] Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top 2007-11-29 14:39 Kostarev Alexey 2007-11-29 15:03 ` Andriy Dobrovol`s`kii 2007-11-30 5:07 ` Kostarev Alexey [this message] 2007-11-30 10:02 ` Sergey Vlasov 2007-11-30 10:56 ` Kostarev Alexey 2007-11-30 11:46 ` Sergey Vlasov
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=474F9A74.6020009@nevod.ru \ --to=kaf@nevod.ru \ --cc=community@lists.altlinux.org \ --cc=sysadmins@lists.altlinux.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: link
ALT Linux Community general discussions This inbox may be cloned and mirrored by anyone: git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 community community/ http://lore.altlinux.org/community \ mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com public-inbox-index community Example config snippet for mirrors. Newsgroup available over NNTP: nntp://lore.altlinux.org/org.altlinux.lists.community AGPL code for this site: git clone https://public-inbox.org/public-inbox.git