From: Michael Shigorin <mike@osdn.org.ua> To: ALT Linux Community <community@lists.altlinux.org> Subject: Re: [Comm] nForce2 & ALC30 Date: Thu, 29 Jun 2006 12:13:26 +0300 Message-ID: <20060629091326.GE520@osdn.org.ua> (raw) In-Reply-To: <200606291154.56060.ashen@nsrz.ru> On Thu, Jun 29, 2006 at 11:54:56AM +0400, Шенцев Алексей Владимирович wrote: > > У меня, кстати, именно оно на именно nf2 и работает. > > Включая сеть и (на предыдущей мамке) абортное видео. > У тебя ALC30 ? Если да, то поделись настройками etcnet ... :) Оно тут ни при чём. А подобные грабли -- интерфейс как бы есть, но не работает, ловил именно с кривым ACPI BIOS. Отключение ACPI хотя бы для PCI или мухлёж с (L)APIC во всех таких случаях помогал. Но вот (их так много скорее потому, что на этой машине в т.ч. тестировались ранние версии etcnet): home:~> cat /etc/net/ifaces/eth1/options DISABLED=no BOOTPROTO=static ONBOOT=yes USE_PCMCIA=no USE_HOTPLUG=no USE_IFPLUGD=no LINKDETECT=no CONFIG_IPV4=yes > И ещё, nf2 у тебя работает под управлением hotplug или нет? home:~> grep -v ^# /etc/sysconfig/hotplug | grep -v ^$ HOTPLUG=yes HOTPLUGRC="usb.rc pnp.rc pci.rc sound.rc" USBPLUG=yes PCIPLUG=yes IEEE1394PLUG=yes NETPLUG=yes SCSIPLUG=yes SOUNDPLUG=yes home:~> lspci 0000:00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different version?) (rev c1) 0000:00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 0 (rev c1) 0000:00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1) 0000:00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1) 0000:00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1) 0000:00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1) 0000:00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4) 0000:00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2) 0000:00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) 0000:00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) 0000:00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) 0000:00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1) 0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP) (rev a1) 0000:00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev a3) 0000:00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2) 0000:00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1) 0000:01:04.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07) 0000:01:04.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 07) 0000:01:08.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46) 0000:01:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 0000:02:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1) Используются модули forcedeth и 8139too. Kernel command line: root=/dev/hda2 panic=600 vga=0x303 (поскольку жалоб на кривой ACPI в dmesg на Shuttle AK40 нет) Фрагмент в р-не загрузки сетевых модулей выглядит так: 8139too Fast Ethernet driver 0.9.27 ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> GSI 17 (level, high) -> IRQ 17 eth0: RealTek RTL8139 at 0xe0c78000, 00:02:44:6b:77:0e, IRQ 17 eth0: Identified 8139 chip type 'RTL-8100B/8139D' eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.35. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 22 (level, high) -> IRQ 22 PCI: Setting latency timer of device 0000:00:04.0 to 64 NET: Registered protocol family 17 eth1: forcedeth.c: subsystem: 01297:0531 bound to 0000:00:04.0 eth1: no link during initialization. -- ---- WBR, Michael Shigorin <mike@altlinux.ru> ------ Linux.Kiev http://www.linux.kiev.ua/
next prev parent reply other threads:[~2006-06-29 9:13 UTC|newest] Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top 2006-06-28 9:05 Шенцев Алексей Владимирович 2006-06-28 9:14 ` Туркин Михаил Александрович 2006-06-28 12:30 ` Aleksander N. Gorohovski 2006-06-28 9:46 ` Шенцев Алексей Владимирович 2006-06-28 9:57 ` Andrey 2006-06-28 10:00 ` Шенцев Алексей Владимирович 2006-06-28 10:09 ` Andrey 2006-06-28 20:33 ` Michael Shigorin 2006-06-29 7:08 ` Шенцев Алексей Владимирович 2006-06-29 7:28 ` Michael Shigorin 2006-06-29 7:44 ` Шенцев Алексей Владимирович 2006-06-29 7:30 ` Туркин Михаил Александрович 2006-06-29 7:40 ` Шенцев Алексей Владимирович 2006-06-29 7:47 ` Michael Shigorin 2006-06-29 7:54 ` Шенцев Алексей Владимирович 2006-06-29 9:13 ` Michael Shigorin [this message] 2006-06-29 9:19 ` Шенцев Алексей Владимирович 2006-06-29 12:22 ` Шенцев Алексей Владимирович 2006-06-29 13:35 ` Alexander Volkov 2006-06-29 13:38 ` Шенцев Алексей Владимирович 2006-06-29 19:00 ` Aleksander N.Gorohovski 2006-06-29 18:11 ` Michael Shigorin 2006-07-04 5:15 ` Genix 2006-07-19 11:56 ` Michael Shigorin
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20060629091326.GE520@osdn.org.ua \ --to=mike@osdn.org.ua \ --cc=community@lists.altlinux.org \ --cc=shigorin@gmail.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: link
ALT Linux Community general discussions This inbox may be cloned and mirrored by anyone: git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git # If you have public-inbox 1.1+ installed, you may # initialize and index your mirror using the following commands: public-inbox-init -V2 community community/ http://lore.altlinux.org/community \ mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com public-inbox-index community Example config snippet for mirrors. Newsgroup available over NNTP: nntp://lore.altlinux.org/org.altlinux.lists.community AGPL code for this site: git clone https://public-inbox.org/public-inbox.git