From: Juriko <juriko@ukr.net>
To: Community@altlinux.ru
Subject: [Comm] Obyasnite, pleez.
Date: Sat, 19 Oct 2002 22:17:56 +0300
Message-ID: <1481602291.20021019221756@ukr.net> (raw)
Здравствуйте Community,
Вчера первый раз в жизни установил дома Linux Junior 2.
Проблема в том, что ни модема, ни звуковой карты не видно.
Материнка - Canyon I815
Звук интегрированный - AC'97
Модем внутренний PCI - Lucent 56K
Может кто поможет "чайнику"?
вывод комманд lspcidrake:
> [juriko@localhost juriko]$ lspcidrake
> agpgart : Intel Corporation|82815 815 Chipset Host Bridge and Memory Controller Hub
> agpgart : Intel Corporation|82815/82815EM/EP AGP Bridge
> i810_rng : Intel Corporation|82820 815e (Camino 2) Chipset PCI
> i810-tco : Intel Corporation|82820 815e (Camino 2) Chipset ISA Bridge (ICH2)
> unknown : Intel Corporation|82820 815e (Camino 2) Chipset IDE U100
> usb-uhci : Intel Corporation|82820 815e (Camino 2) Chipset USB (Hub A)
> unknown : Intel Corporation|82820 815e (Camino 2) Chipset SMBus
> usb-uhci : Intel Corporation|82820 815e (Camino 2) Chipset USB (Hub B)
> snd-intel8x0 : Intel Corporation|ICH2 810 Chipset AC'97 Audio Controller
> Card:ATI Rage 128: ATI|Rage 128 Pro AGP 4x
> Bad:www.linmodems.org: Lucent Microelectronics|LT WinModem
> unknown : Virtual|Hub []
> unknown : Virtual|Hub []
> [juriko@localhost juriko]$
содержимое файла /proc/bus/pci/devices:
> 0000 80861130 0 e0000008 00000000 00000000 00000000 00000000 00000000 00000000 04000000 00000000 00000000 00000000 00000000 00000000 00000000
> 0008 80861131 0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> 00f0 8086244e 0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> 00f8 80862440 0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Intel ICH Joystick
> 00f9 8086244b 0 00000000 00000000 00000000 00000000 0000f001 00000000 00000000 00000000 00000000 00000000 00000000 00000010 00000000 00000000
> 00fa 80862442 b 00000000 00000000 00000000 00000000 0000b001 00000000 00000000 00000000 00000000 00000000 00000000 00000020 00000000 00000000 usb-uhci
> 00fb 80862443 5 00000000 00000000 00000000 00000000 00000501 00000000 00000000 00000000 00000000 00000000 00000000 00000010 00000000 00000000
> 00fc 80862444 9 00000000 00000000 00000000 00000000 0000b801 00000000 00000000 00000000 00000000 00000000 00000000 00000020 00000000 00000000 usb-uhci
> 00fd 80862445 5 0000bc01 0000c001 00000000 00000000 00000000 00000000 00000000 00000100 00000040 00000000 00000000 00000000 00000000 00000000 Intel ICH
> 0100 10025046 b e4000008 00009001 e9000000 00000000 00000000 00000000 00000000 04000000 00000100 00004000 00000000 00000000 00000000 00020000
> 0248 11c1044c 5 ea000000 0000a001 0000a401 00000000 00000000 00000000 00000000 00000100 00000008 00000100 00000000 00000000 00000000 00000000
и lspci -vv:
> lspci -vv
> 00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory Controller Hub (rev 04)
> Subsystem: Intel Corp.: Unknown device 0000
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSELъst >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at e0000000 (32-bit, prefetchable) [sizedM]
> Capabilities: <available only to root>
>
> 00:01.0 PCI bridge: Intel Corp.: Unknown device 1131 (rev 04) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSELъst >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32
> Bus: primary=00, secondary\x01, subordinate\x01, sec-latency2
> I/O behind bridge: 00009000-00009fff
> Memory behind bridge: e8000000-e9ffffff
> Prefetchable memory behind bridge: e4000000-e7ffffff
> BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
>
> 00:1e.0 PCI bridge: Intel Corp. 82820 820 (Camino 2) Chipset PCI (rev 05) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSELъst >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary\x02, subordinate\x02, sec-latency2
> I/O behind bridge: 0000a000-0000afff
> Memory behind bridge: ea000000-ea0fffff
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
>
> 00:1f.0 ISA bridge: Intel Corp. 82820 820 (Camino 2) Chipset ISA Bridge (ICH2) (rev 05)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:1f.1 IDE interface: Intel Corp. 82820 820 (Camino 2) Chipset IDE U100 (rev 05) (prog-if 80 [Master])
> Subsystem: Intel Corp.: Unknown device 2442
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Region 4: I/O ports at f000 [size\x16]
>
> 00:1f.2 USB Controller: Intel Corp. 82820 820 (Camino 2) Chipset USB (Hub A) (rev 05) (prog-if 00 [UHCI])
> Subsystem: Intel Corp. 82820 820 (Camino 2) Chipset USB (Hub A)
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin D routed to IRQ 11
> Region 4: I/O ports at b000 [size2]
>
> 00:1f.3 SMBus: Intel Corp. 82820 820 (Camino 2) Chipset SMBus (rev 05)
> Subsystem: Intel Corp.: Unknown device 2442
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin B routed to IRQ 5
> Region 4: I/O ports at 0500 [size\x16]
>
> 00:1f.4 USB Controller: Intel Corp. 82820 820 (Camino 2) Chipset USB (Hub B) (rev 05) (prog-if 00 [UHCI])
> Subsystem: Intel Corp.: Unknown device 2442
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin C routed to IRQ 9
> Region 4: I/O ports at b800 [size2]
>
> 00:1f.5 Multimedia audio controller: Intel Corp. 82820 820 (Camino 2) Chipset AC'97 Audio Controller (rev 05)
> Subsystem: Unknown device 414c:4710
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 5
> Region 0: I/O ports at bc00 [size%6]
> Region 1: I/O ports at c000 [sized]
>
> 01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 PF (prog-if 00 [VGA])
> Subsystem: ATI Technologies Inc: Unknown device 0004
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (2000ns min), cache line size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at e4000000 (32-bit, prefetchable) [sizedM]
> Region 1: I/O ports at 9000 [size%6]
> Region 2: Memory at e9000000 (32-bit, non-prefetchable) [size\x16K]
> Expansion ROM at <unassigned> [disabled] [size\x128K]
> Capabilities: <available only to root>
>
> 02:09.0 Communication controller: Lucent Microelectronics LT WinModem (rev 02)
> Subsystem: Lucent Microelectronics LT WinModem
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (63000ns min, 3500ns max)
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at ea000000 (32-bit, non-prefetchable) [size%6]
> Region 1: I/O ports at a000 [size=8]
> Region 2: I/O ports at a400 [size%6]
> Capabilities: <available only to root>
Спасибо.
--
С уважением,
Юрий Сергеевич
mailto:juriko@ukr.net
next reply other threads:[~2002-10-19 19:17 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-10-19 19:17 Juriko [this message]
2002-10-19 19:26 ` Sergey Degtyaryov
2002-10-19 20:16 ` Ilia Menchikh
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1481602291.20021019221756@ukr.net \
--to=juriko@ukr.net \
--cc=Community@altlinux.ru \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
ALT Linux Community general discussions
This inbox may be cloned and mirrored by anyone:
git clone --mirror http://lore.altlinux.org/community/0 community/git/0.git
# If you have public-inbox 1.1+ installed, you may
# initialize and index your mirror using the following commands:
public-inbox-init -V2 community community/ http://lore.altlinux.org/community \
mandrake-russian@linuxteam.iplabs.ru community@lists.altlinux.org community@lists.altlinux.ru community@lists.altlinux.com
public-inbox-index community
Example config snippet for mirrors.
Newsgroup available over NNTP:
nntp://lore.altlinux.org/org.altlinux.lists.community
AGPL code for this site: git clone https://public-inbox.org/public-inbox.git